On 10/16/19 1:28 PM, Mihaita Ivascu wrote: > On Wed, Oct 16, 2019 at 11:53 AM Ahmad Fatoum <a.fatoum@xxxxxxxxxxxxxx> > wrote: >> >> >> On 10/16/19 11:48 AM, Mihaita Ivascu wrote: >>> On Wed, Oct 16, 2019 at 11:26 AM Ahmad Fatoum <a.fatoum@xxxxxxxxxxxxxx> > wrote: >>>> >>>> On 10/16/19 11:21 AM, Mihaita Ivascu wrote: >>>>> Hello, >>>>> >>>>> Thanks for your answer. Yes i am able to connect via PUTTY to the > target. >>>>> Then I should use some adb commands in order to push the new >>>>> barebox/firmware ? do you know where I could find some examples? >>>> >>>> fastboot device -l works normally on Linux. You need to check what you > need >>>> to do on Windows to do the same. You should only need the Fastboot > utility >>>> for this. >>>> >>> [mi] Yes I have both fastboot and adb installed on both Windows and >>> Linux machines. In both cases it does not list any device. >>> The board is detected as fastboot android is windows device >>> manager. But the fastboot and adb does not list it. same for Linux. >>> Please see attachment >> >> Let's focus on Linux. You don't see a device there? >> What does barebox say? Does it say 'multi_bind: creating Fastboot > function'? >> What does you Linux host's dmesg say? >> > > barebox@Phytec phyCORE-i.MX6 Ultra Lite SOM:/ usbgadget -aA > udc0: registering UDC driver [g_multi] > multi_bind: creating Fastboot function > multi_bind: creating ACM function > g_multi usbgadget: Multifunction Composite Gadget > g_multi usbgadget: userspace failed to provide iSerialNumber > g_multi usbgadget: g_multi ready > barebox@Phytec phyCORE-i.MX6 Ultra Lite SOM:/ g_multi usbgadget: high-speed > config #1: Multifunction Composite Gadget > > dmesg: > > [ 25.602275] usb 1-1.3: USB disconnect, device number 3 > [ 28.359930] usb 1-1.3: new high-speed USB device number 5 using ehci-pci > [ 28.452971] usb 1-1.3: New USB device found, idVendor=1d6b, > idProduct=0104 > [ 28.452976] usb 1-1.3: New USB device strings: Mfr=0, Product=2, > SerialNumber=0 > [ 28.452980] usb 1-1.3: Product: Phytec phyCORE-i.MX6 Ultra Lite SOM > [ 28.457925] cdc_acm 1-1.3:1.1: ttyACM0: USB ACM device > > > So I see the device on Linux. But fastboot does not list any device on > Linux. sudo doesn't change this? > >> > >>>>> >>>>> Also I have a question: purpose of this activity is for me to be >>>>> able to flash some imx6ul boards that have no firmware: no barebox. >>>>> So I know hardware config for the port is otg mode but as I have no >>>>> barebox running them before I am wondering if I will be able to >>>>> connect via PUTTY if I do not set the ACM gadget from barebox? >>>> >>>> Check the Embest MarS board's environment in barebox master. It sets up >>>> a fastboot gadget automatically on boot from imx-usb-loader. >>>> You can adjust it to your liking. >>> >>> [mi] I was not able to find any docs about this board. I will keep >>> searching/asking in the nxp community. If you have already ahve any >>> files related to it would be helpful. Thanks >> >> It's in the barebox next branch (not master, sorry), see here: >> > https://github.com/saschahauer/barebox/blob/next/arch/arm/boards/embest-marsboard/defaultenv-mars/init/fastboot >> >> You can copy and adjust the environment setup for your board. >> >>>> >>>> Cheers >>>> Ahmad >>>> >>>>> >>>>> Thanks, >>>>> Mihaita >>>>> >>>>> On Wed, Oct 16, 2019 at 10:51 AM Ahmad Fatoum <a.fatoum@xxxxxxxxxxxxxx> > wrote: >>>>>> >>>>>> On 10/16/19 10:40 AM, Mihaita Ivascu wrote: >>>>>>> Hello again, >>>>>>> >>>>>>> I have the target in otg peripheral mode, ADB and fastboot > drivers >>>>>>> installed but fastboot does not list any device. The board is > detected >>>>>>> in device manager >>>>>> >>>>>> Try enabling the ACM gadget in barebox and connect with PuTTY and > see if >>>>>> at least that works. It worked for me on Windows with another i.MX > board >>>>>> a month ago. >>>>>> >>>>>> As for fastboot, I don't know how to configure it on Windows, but > surely >>>>>> Android Modding boards will have you covered there. >>>>>> >>>>>>> Please see attachment. Any ideas how should I proceed? Thanks for >>>>>>> the support. >>>>>> >>>>>> You can enable the ACM gadget in barebox and see if that works, I > tested >>>>>> it on Windows with an i.MX board a month ago >>>>>> >>>>>> Cheers >>>>>> Ahmad >>>>>> >>>>>>> >>>>>>> Thanks, >>>>>>> Mihaita >>>>>>> >>>>>>> On Wed, Oct 16, 2019 at 9:32 AM Mihaita Ivascu >>>>>>> <mihaita_ivascu@xxxxxxxxxxx> wrote: >>>>>>>> >>>>>>>> Thanks. I have installed ADB and fastboot drivers for Win from >>>>>>>> > https://www.getdroidtips.com/how-to-install-adb-and-fastboot-on-windows/ >>>>>>>> I have installed according to the attachment. >>>>>>>> But is not recognized in Windows. I did reboot the system after >>>>>>>> installation but did not add any new env variable. >>>>>>>> >>>>>>>> H:\>fastboot devices -l >>>>>>>> 'fastboot' is not recognized as an internal or external command, >>>>>>>> operable program or batch file. >>>>>>>> >>>>>>>> Thanks, >>>>>>>> Mihaita >>>>>>>> >>>>>>>> >>>>>>>> On Tue, Oct 15, 2019 at 4:44 PM Ahmad Fatoum < > a.fatoum@xxxxxxxxxxxxxx> wrote: >>>>>>>>> >>>>>>>>> On 10/15/19 4:41 PM, Mihaita Ivascu wrote: >>>>>>>>>> barebox@Phytec phyCORE-i.MX6 Ultra Lite SOM:/ fastboot devices -l >>>>>>>>> That's what you run on your host system, not on the target. >>>>>>>>> -- >>>>>>>>> Pengutronix e.K. | > | >>>>>>>>> Industrial Linux Solutions | > http://www.pengutronix.de/ | >>>>>>>>> Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: > +49-5121-206917-0 | >>>>>>>>> Amtsgericht Hildesheim, HRA 2686 | Fax: > +49-5121-206917-5555 | >>>>>> >>>>>> >>>>>> -- >>>>>> Pengutronix e.K. | > | >>>>>> Industrial Linux Solutions | > http://www.pengutronix.de/ | >>>>>> Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: > +49-5121-206917-0 | >>>>>> Amtsgericht Hildesheim, HRA 2686 | Fax: > +49-5121-206917-5555 | >>>>> >>>> >>>> >>>> -- >>>> Pengutronix e.K. | > | >>>> Industrial Linux Solutions | http://www.pengutronix.de/ > | >>>> Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 > | >>>> Amtsgericht Hildesheim, HRA 2686 | Fax: > +49-5121-206917-5555 | >> >> -- >> Pengutronix e.K. | | >> Industrial Linux Solutions | http://www.pengutronix.de/ | >> Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | >> Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | > -- Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list barebox@xxxxxxxxxxxxxxxxxxx http://lists.infradead.org/mailman/listinfo/barebox
