No it does not. Still no devices listed.
Thanks,
Mihaita
On Wed, Oct 16, 2019 at 1:36 PM Ahmad Fatoum <a.fatoum@xxxxxxxxxxxxxx> wrote:
>
> On 10/16/19 1:28 PM, Mihaita Ivascu wrote:
> > On Wed, Oct 16, 2019 at 11:53 AM Ahmad Fatoum <a.fatoum@xxxxxxxxxxxxxx>
> > wrote:
> >>
> >>
> >> On 10/16/19 11:48 AM, Mihaita Ivascu wrote:
> >>> On Wed, Oct 16, 2019 at 11:26 AM Ahmad Fatoum <a.fatoum@xxxxxxxxxxxxxx>
> > wrote:
> >>>>
> >>>> On 10/16/19 11:21 AM, Mihaita Ivascu wrote:
> >>>>> Hello,
> >>>>>
> >>>>> Thanks for your answer. Yes i am able to connect via PUTTY to the
> > target.
> >>>>> Then I should use some adb commands in order to push the new
> >>>>> barebox/firmware ? do you know where I could find some examples?
> >>>>
> >>>> fastboot device -l works normally on Linux. You need to check what you
> > need
> >>>> to do on Windows to do the same. You should only need the Fastboot
> > utility
> >>>> for this.
> >>>>
> >>> [mi] Yes I have both fastboot and adb installed on both Windows and
> >>> Linux machines. In both cases it does not list any device.
> >>> The board is detected as fastboot android is windows device
> >>> manager. But the fastboot and adb does not list it. same for Linux.
> >>> Please see attachment
> >>
> >> Let's focus on Linux. You don't see a device there?
> >> What does barebox say? Does it say 'multi_bind: creating Fastboot
> > function'?
> >> What does you Linux host's dmesg say?
> >>
> >
> > barebox@Phytec phyCORE-i.MX6 Ultra Lite SOM:/ usbgadget -aA
> > udc0: registering UDC driver [g_multi]
> > multi_bind: creating Fastboot function
> > multi_bind: creating ACM function
> > g_multi usbgadget: Multifunction Composite Gadget
> > g_multi usbgadget: userspace failed to provide iSerialNumber
> > g_multi usbgadget: g_multi ready
> > barebox@Phytec phyCORE-i.MX6 Ultra Lite SOM:/ g_multi usbgadget: high-speed
> > config #1: Multifunction Composite Gadget
> >
> > dmesg:
> >
> > [ 25.602275] usb 1-1.3: USB disconnect, device number 3
> > [ 28.359930] usb 1-1.3: new high-speed USB device number 5 using ehci-pci
> > [ 28.452971] usb 1-1.3: New USB device found, idVendor=1d6b,
> > idProduct=0104
> > [ 28.452976] usb 1-1.3: New USB device strings: Mfr=0, Product=2,
> > SerialNumber=0
> > [ 28.452980] usb 1-1.3: Product: Phytec phyCORE-i.MX6 Ultra Lite SOM
> > [ 28.457925] cdc_acm 1-1.3:1.1: ttyACM0: USB ACM device
> >
> >
> > So I see the device on Linux. But fastboot does not list any device on
> > Linux.
>
> sudo doesn't change this?
>
> >
> >> >
> >>>>>
> >>>>> Also I have a question: purpose of this activity is for me to be
> >>>>> able to flash some imx6ul boards that have no firmware: no barebox.
> >>>>> So I know hardware config for the port is otg mode but as I have no
> >>>>> barebox running them before I am wondering if I will be able to
> >>>>> connect via PUTTY if I do not set the ACM gadget from barebox?
> >>>>
> >>>> Check the Embest MarS board's environment in barebox master. It sets up
> >>>> a fastboot gadget automatically on boot from imx-usb-loader.
> >>>> You can adjust it to your liking.
> >>>
> >>> [mi] I was not able to find any docs about this board. I will keep
> >>> searching/asking in the nxp community. If you have already ahve any
> >>> files related to it would be helpful. Thanks
> >>
> >> It's in the barebox next branch (not master, sorry), see here:
> >>
> > https://github.com/saschahauer/barebox/blob/next/arch/arm/boards/embest-marsboard/defaultenv-mars/init/fastboot
> >>
> >> You can copy and adjust the environment setup for your board.
> >>
> >>>>
> >>>> Cheers
> >>>> Ahmad
> >>>>
> >>>>>
> >>>>> Thanks,
> >>>>> Mihaita
> >>>>>
> >>>>> On Wed, Oct 16, 2019 at 10:51 AM Ahmad Fatoum <a.fatoum@xxxxxxxxxxxxxx>
> > wrote:
> >>>>>>
> >>>>>> On 10/16/19 10:40 AM, Mihaita Ivascu wrote:
> >>>>>>> Hello again,
> >>>>>>>
> >>>>>>> I have the target in otg peripheral mode, ADB and fastboot
> > drivers
> >>>>>>> installed but fastboot does not list any device. The board is
> > detected
> >>>>>>> in device manager
> >>>>>>
> >>>>>> Try enabling the ACM gadget in barebox and connect with PuTTY and
> > see if
> >>>>>> at least that works. It worked for me on Windows with another i.MX
> > board
> >>>>>> a month ago.
> >>>>>>
> >>>>>> As for fastboot, I don't know how to configure it on Windows, but
> > surely
> >>>>>> Android Modding boards will have you covered there.
> >>>>>>
> >>>>>>> Please see attachment. Any ideas how should I proceed? Thanks for
> >>>>>>> the support.
> >>>>>>
> >>>>>> You can enable the ACM gadget in barebox and see if that works, I
> > tested
> >>>>>> it on Windows with an i.MX board a month ago
> >>>>>>
> >>>>>> Cheers
> >>>>>> Ahmad
> >>>>>>
> >>>>>>>
> >>>>>>> Thanks,
> >>>>>>> Mihaita
> >>>>>>>
> >>>>>>> On Wed, Oct 16, 2019 at 9:32 AM Mihaita Ivascu
> >>>>>>> <mihaita_ivascu@xxxxxxxxxxx> wrote:
> >>>>>>>>
> >>>>>>>> Thanks. I have installed ADB and fastboot drivers for Win from
> >>>>>>>>
> > https://www.getdroidtips.com/how-to-install-adb-and-fastboot-on-windows/
> >>>>>>>> I have installed according to the attachment.
> >>>>>>>> But is not recognized in Windows. I did reboot the system after
> >>>>>>>> installation but did not add any new env variable.
> >>>>>>>>
> >>>>>>>> H:\>fastboot devices -l
> >>>>>>>> 'fastboot' is not recognized as an internal or external command,
> >>>>>>>> operable program or batch file.
> >>>>>>>>
> >>>>>>>> Thanks,
> >>>>>>>> Mihaita
> >>>>>>>>
> >>>>>>>>
> >>>>>>>> On Tue, Oct 15, 2019 at 4:44 PM Ahmad Fatoum <
> > a.fatoum@xxxxxxxxxxxxxx> wrote:
> >>>>>>>>>
> >>>>>>>>> On 10/15/19 4:41 PM, Mihaita Ivascu wrote:
> >>>>>>>>>> barebox@Phytec phyCORE-i.MX6 Ultra Lite SOM:/ fastboot devices -l
> >>>>>>>>> That's what you run on your host system, not on the target.
> >>>>>>>>> --
> >>>>>>>>> Pengutronix e.K. |
> > |
> >>>>>>>>> Industrial Linux Solutions |
> > http://www.pengutronix.de/ |
> >>>>>>>>> Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone:
> > +49-5121-206917-0 |
> >>>>>>>>> Amtsgericht Hildesheim, HRA 2686 | Fax:
> > +49-5121-206917-5555 |
> >>>>>>
> >>>>>>
> >>>>>> --
> >>>>>> Pengutronix e.K. |
> > |
> >>>>>> Industrial Linux Solutions |
> > http://www.pengutronix.de/ |
> >>>>>> Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone:
> > +49-5121-206917-0 |
> >>>>>> Amtsgericht Hildesheim, HRA 2686 | Fax:
> > +49-5121-206917-5555 |
> >>>>>
> >>>>
> >>>>
> >>>> --
> >>>> Pengutronix e.K. |
> > |
> >>>> Industrial Linux Solutions | http://www.pengutronix.de/
> > |
> >>>> Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0
> > |
> >>>> Amtsgericht Hildesheim, HRA 2686 | Fax:
> > +49-5121-206917-5555 |
> >>
> >> --
> >> Pengutronix e.K. | |
> >> Industrial Linux Solutions | http://www.pengutronix.de/ |
> >> Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
> >> Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
> >
>
> --
> Pengutronix e.K. | |
> Industrial Linux Solutions | http://www.pengutronix.de/ |
> Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
> Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
_______________________________________________
barebox mailing list
barebox@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/barebox
