On 10/16/19 11:21 AM, Mihaita Ivascu wrote: > Hello, > > Thanks for your answer. Yes i am able to connect via PUTTY to the target. > Then I should use some adb commands in order to push the new > barebox/firmware ? do you know where I could find some examples? fastboot device -l works normally on Linux. You need to check what you need to do on Windows to do the same. You should only need the Fastboot utility for this. > > Also I have a question: purpose of this activity is for me to be > able to flash some imx6ul boards that have no firmware: no barebox. > So I know hardware config for the port is otg mode but as I have no > barebox running them before I am wondering if I will be able to > connect via PUTTY if I do not set the ACM gadget from barebox? Check the Embest MarS board's environment in barebox master. It sets up a fastboot gadget automatically on boot from imx-usb-loader. You can adjust it to your liking. Cheers Ahmad > > Thanks, > Mihaita > > On Wed, Oct 16, 2019 at 10:51 AM Ahmad Fatoum <a.fatoum@xxxxxxxxxxxxxx> wrote: >> >> On 10/16/19 10:40 AM, Mihaita Ivascu wrote: >>> Hello again, >>> >>> I have the target in otg peripheral mode, ADB and fastboot drivers >>> installed but fastboot does not list any device. The board is detected >>> in device manager >> >> Try enabling the ACM gadget in barebox and connect with PuTTY and see if >> at least that works. It worked for me on Windows with another i.MX board >> a month ago. >> >> As for fastboot, I don't know how to configure it on Windows, but surely >> Android Modding boards will have you covered there. >> >>> Please see attachment. Any ideas how should I proceed? Thanks for >>> the support. >> >> You can enable the ACM gadget in barebox and see if that works, I tested >> it on Windows with an i.MX board a month ago >> >> Cheers >> Ahmad >> >>> >>> Thanks, >>> Mihaita >>> >>> On Wed, Oct 16, 2019 at 9:32 AM Mihaita Ivascu >>> <mihaita_ivascu@xxxxxxxxxxx> wrote: >>>> >>>> Thanks. I have installed ADB and fastboot drivers for Win from >>>> https://www.getdroidtips.com/how-to-install-adb-and-fastboot-on-windows/ >>>> I have installed according to the attachment. >>>> But is not recognized in Windows. I did reboot the system after >>>> installation but did not add any new env variable. >>>> >>>> H:\>fastboot devices -l >>>> 'fastboot' is not recognized as an internal or external command, >>>> operable program or batch file. >>>> >>>> Thanks, >>>> Mihaita >>>> >>>> >>>> On Tue, Oct 15, 2019 at 4:44 PM Ahmad Fatoum <a.fatoum@xxxxxxxxxxxxxx> wrote: >>>>> >>>>> On 10/15/19 4:41 PM, Mihaita Ivascu wrote: >>>>>> barebox@Phytec phyCORE-i.MX6 Ultra Lite SOM:/ fastboot devices -l >>>>> That's what you run on your host system, not on the target. >>>>> -- >>>>> Pengutronix e.K. | | >>>>> Industrial Linux Solutions | http://www.pengutronix.de/ | >>>>> Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | >>>>> Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | >> >> >> -- >> Pengutronix e.K. | | >> Industrial Linux Solutions | http://www.pengutronix.de/ | >> Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | >> Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | > -- Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list barebox@xxxxxxxxxxxxxxxxxxx http://lists.infradead.org/mailman/listinfo/barebox
