On Mon, Aug 13, 2012 at 06:52:13PM +0530, Munegowda, Keshava wrote: > On Fri, Jul 27, 2012 at 5:44 PM, Munegowda, Keshava > <keshava_mgowda@xxxxxx> wrote: > > On Mon, Jul 23, 2012 at 8:04 PM, Munegowda, Keshava > > <keshava_mgowda@xxxxxx> wrote: > >> On Mon, Jul 23, 2012 at 7:38 PM, Felipe Balbi <balbi@xxxxxx> wrote: > >>> Hi, > >>> > >>> On Mon, Jul 23, 2012 at 07:31:10PM +0530, Munegowda, Keshava wrote: > >>>> On Thu, Jul 19, 2012 at 3:48 PM, Munegowda, Keshava > >>>> <keshava_mgowda@xxxxxx> wrote: > >>>> > On Mon, Jul 16, 2012 at 7:01 PM, Keshava Munegowda > >>>> > <keshava_mgowda@xxxxxx> wrote: > >>>> >> The TLL (Transceiver Less Link) is an separate IP block, independent of > >>>> >> the host controller. Basically this TLL operates like USB PHY which allows > >>>> >> the user to connect two USB transceiver interfaces together directly > >>>> >> without the use of differential transceivers in omap3 and later chips. > >>>> >> The TLL configuration is removed from the UHH driver and implemented as > >>>> >> a seperate platform driver. Now, the UHH driver configures the TLL > >>>> >> through API's exported by the TLL platform driver. > >>>> >> > >>>> >> Signed-off-by: Keshava Munegowda <keshava_mgowda@xxxxxx> > >>>> >> > >>>> >> In v4: > >>>> >> - rebased on top of linux kernel version 3.5.rc7 > >>>> >> - reworked as per the comments given by Paul Walmsley <paul@xxxxxxxxx> > >>>> >> > >>>> >> In v3: > >>>> >> - rebased on top V3 of Russ dill's patch > >>>> >> 'ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset issue' > >>>> >> fixes an issue where the ULPI PHYs were not held in reset > >>>> >> while initializing the EHCI controller > >>>> >> http://permalink.gmane.org/gmane.linux.usb.general/65988 > >>>> >> > >>>> >> - rebased on top of patch > >>>> >> OMAP: USB : Fix the EHCI enumeration and core retention issue > >>>> >> http://permalink.gmane.org/gmane.linux.usb.general/66239 > >>>> >> > >>>> >> In V2: > >>>> >> - covered review comments from linux omap and usb community > >>>> >> - rebased on top Russ dill's patch > >>>> >> 'ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset issue' > >>>> >> fixes an issue where the ULPI PHYs were not held in reset > >>>> >> while initializing the EHCI controller > >>>> >> > >>>> >> Keshava Munegowda (5): > >>>> >> ARM: OMAP: Add the USB TLL clocks device name > >>>> >> ARM: OMAP: USB: HOST TLL platform driver > >>>> >> ARM: OMAP: USB: Invoke the TLL driver from USB HS core driver > >>>> >> ARM: OMAP: USB: Remove TLL specific code from USB HS core driver > >>>> >> ARM: OMAP: Remove older device name of the USB TLL clocks > >>>> >> > >>>> >> arch/arm/mach-omap2/clock3xxx_data.c | 8 +- > >>>> >> arch/arm/mach-omap2/clock44xx_data.c | 4 +- > >>>> >> arch/arm/mach-omap2/usb-host.c | 31 ++- > >>>> >> arch/arm/plat-omap/include/plat/usb.h | 7 + > >>>> >> drivers/mfd/Kconfig | 2 +- > >>>> >> drivers/mfd/Makefile | 2 +- > >>>> >> drivers/mfd/omap-usb-host.c | 238 ++--------------- > >>>> >> drivers/mfd/omap-usb-tll.c | 471 +++++++++++++++++++++++++++++++++ > >>>> >> 8 files changed, 523 insertions(+), 240 deletions(-) > >>>> >> create mode 100644 drivers/mfd/omap-usb-tll.c > >>>> >> > >>>> >> -- > >>>> >> 1.7.9.5 > >>>> > > >>>> > > >>>> > Felipe/ Paul > >>>> > please let me know if you have any review comments on this v4 series. > >>>> > > >>>> > regards > >>>> > keshava > >>>> > >>>> Hi Felipe > >>>> please let me know if you have any review comments on this series now. > >>> > >>> looks ok... pretty much just moving code around. > >>> > >>> -- > >>> balbi > >> > >> > >> Thanks Felipe > >> > >> then I request please give your Ack by for this series. > >> > >> regards > >> keshava > > > > Hi Paul > > do you have any review comments on this series? > > Felipe is OK with this series. if there are no review comments on this series > > I request your ack by for the same. > > Once this series gets in to mainline. i will start the Device tree > > conversion for usb2 host. > > > > regards > > keshava > > Hi Felipe > please give you ack by this series , so that I request > samuel to merge to mainline. sure, here you go Acked-by: Felipe Balbi <balbi@xxxxxx> -- balbi
Attachment:
signature.asc
Description: Digital signature
