If you can give me a link or mail me your driver I could give it a try too. -Mika Marko Ristola wrote: > > Maybe I should try with Manu's jusst.de version, if it works for me now > Better exclude the driver differences away. > I don't have a CAM module and I haven't tested with two equal cards. > > Our problems seem to be similar though. > > Marko > > Mika Båtsman kirjoitti: >> Marko Ristola wrote: >>> Mika Båtsman kirjoitti: >>>> Hi, >>>> I also tried your patch because I've had freezes since I got these >>>> cards. Unfortunately it didn't help me. Got a whooping 5min uptime >>>> before it all went wrong again. I have 2x Cinergy C + 2.6.24-19 + >>>> vdr 1.6. >>>> >>> Do you have a heat problem? Have you checked your motherboard sensors? >>> Have you checked that your memory is okay? Air flows easilly? >> >> Memory was the first thing I suspected but memtest went through 10+ >> times without a fail. Heat shouldn't be a problem either. There's a >> big efficient, noisy fan in the back of the case. >> >> The machine works fine when dvb is watched with dvbyell >> http://www.dvbyell.org/ which has cards set to fixed frequency ie. >> card1 -> 152Mhz and card2 -> 290Mhz. At least for me the problem >> occurs only with apps like mythtv and vdr which change the frequency >> of the tuner. >> >> -Mika >> >>>> I did: >>>> hg clone http://jusst.de/hg/mantis >>>> replaced mantis_dma.c with the one you attached, renamed >>>> MANTIS_GPIF_RDWRN -> MANTIS_GPIF_HIFRDWRN >>>> make && make install && reboot >>>> >>>> Am I missing something? It seemed to compile and install fine. >>>> >>>> You said that the mantis_dma.c in jusst.de mantis head is not the >>>> latest version. Where can it be found then? >>> I have my own driver version which I have given for Finnish people >>> for easy installation with remote control support for Twinhan 2033. >>> (Personally I'm not pleased with the card: now after some years of >>> development the card works well enough for me finally). >>> >>> So the most important feature of my driver for Finnish people has >>> been the easy compile and install and that the driver ("release") is >>> tested for Twinhan 2033. >>> Secondly I have given for some Finnish people the Twinhan 2033 remote >>> control support included. >>> Maybe somebody from Finland would be interested with the DMA transfer >>> fixes, if they have unsolved quality problems. That's a fact that >>> those tweaks helped me although the root cause is a bit uncertain. >>> Other features of my driver version like suspend/resume aren't very >>> important. >>> >>> Regards, >>> Marko Ristola >>> >>>> >>>> Regards, >>>> Mika Båtsman >>>> >>>> Marko Ristola wrote: >>>>> >>>>> Hi, >>>>> >>>>> Unfortunately I have been busy. >>>>> >>>>> The patch you tried was against jusst.de Mantis Mercurial branch head. >>>>> Your version of mantis_dma.c is not the latest version and thus the >>>>> patch didn't >>>>> apply cleanly. >>>>> >>>>> Here is the version that I use currently. It doesn't compile >>>>> straight against jusst.de/mantis head. >>>>> It might work for you because MANTIS_GPIF_RDWRN is not renamed as >>>>> MANTIS_GPIF_HIFRDWRN. >>>>> >>>>> If it doesn't compile please rename MANTIS_GPIF_RDWRN occurrences >>>>> into MANTIS_GPIF_HIFRDWRN on that file. >>>>> Otherwise the file should work as it is. >>>>> >>>>> Best regards, >>>>> Marko Ristola >>>>> >>>>> Leif Oberste-Berghaus kirjoitti: >>>>>> Hi Marko, >>>>>> >>>>>> I tried to patch the driver but I'm getting an error message: >>>>>> >>>>>> root@mediapc:/usr/local/src/test/mantis-0b04be0c088a# patch -p1 < >>>>>> mantis_dma.c.aligned_dma_trs.patch >>>>>> patching file linux/drivers/media/dvb/mantis/mantis_dma.c >>>>>> patch: **** malformed patch at line 22: int mantis_dma_exit(struct >>>>>> mantis_pci *mantis) >>>>>> >>>>>> Any ideas? >>>>>> >>>>>> Regards >>>>>> Leif >>>>>> >>>>>> >>>>>> Am 14.07.2008 um 22:05 schrieb Marko Ristola: >>>>>> >>>>>>> Hi Leif, >>>>>>> >>>>>>> Here is a patch that implements the mentioned DMA transfer >>>>>>> improvements. >>>>>>> I hope that these contain also the needed fix for you. >>>>>>> You can apply it into jusst.de/mantis Mercurial branch. >>>>>>> It modifies linux/drivers/media/dvb/mantis/mantis_dma.c only. >>>>>>> I have compiled the patch against 2.6.25.9-76.fc9.x86_64. >>>>>>> >>>>>>> cd mantis >>>>>>> patch -p1 < mantis_dma.c.aligned_dma_trs.patch >>>>>>> >>>>>>> Please tell us whether my patch helps you or not: if it helps, >>>>>>> some of my patch might get into jusst.de as >>>>>>> a fix for your problem. >>>>>>> >>>>>>> Best Regards, >>>>>>> Marko >>>>>> >>>>>> >>>>> >>>>> ------------------------------------------------------------------------ >>>>> >>>>> >>>>> _______________________________________________ >>>>> linux-dvb mailing list >>>>> linux-dvb@xxxxxxxxxxx >>>>> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb >>>> >>> >> >> > _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
