Hi I have one of these, saw Stevens post and thought i would give it a go. I built from : http://linuxtv.org/hg/~stoth/v4l-dvb All seemed to go well with no errors. dmesg reads: [ 31.964424] CORE cx23885[0]: subsystem: 18ac:db78, board: DViCO FusionHDTV DVB-T Dual Express [card=11,autodetected] [ 32.104767] cx23885[0]: i2c bus 0 registered [ 32.104781] cx23885[0]: i2c bus 1 registered [ 32.104794] cx23885[0]: i2c bus 2 registered [ 32.164385] input: i2c IR (FusionHDTV) as /devices/virtual/input/input8 [ 32.422764] ir-kbd-i2c: i2c IR (FusionHDTV) detected at i2c-1/1-006b/ir0 [cx23885[0]] [ 32.423135] cx23885[0]: cx23885 based dvb card [ 32.492021] xc2028 1-0061: creating new instance [ 32.492027] xc2028 1-0061: type set to XCeive xc2028/xc3028 tuner [ 32.492036] DVB: registering new adapter (cx23885[0]) [ 32.492040] DVB: registering frontend 0 (Zarlink ZL10353 DVB-T)... [ 32.492386] cx23885[0]: cx23885 based dvb card [ 32.492924] xc2028 2-0061: creating new instance [ 32.492926] xc2028 2-0061: type set to XCeive xc2028/xc3028 tuner [ 32.492928] DVB: registering new adapter (cx23885[0]) [ 32.492930] DVB: registering frontend 1 (Zarlink ZL10353 DVB-T)... [ 32.493228] cx23885_dev_checkrevision() Hardware revision = 0xb0 [ 32.493236] cx23885[0]/0: found at 0000:02:00.0, rev: 2, irq: 16, latency: 0, mmio: 0xfe800000 But scanning, returns : [ 1381.214624] xc2028 1-0061: Error: firmware xc3028-v27.fw not found. [ 1382.220858] xc2028 1-0061: Error: firmware xc3028-v27.fw not found. [ 1382.260825] xc2028 1-0061: Error: firmware xc3028-v27.fw not found. [ 1383.267724] xc2028 1-0061: Error: firmware xc3028-v27.fw not found. [ 1383.276680] xc2028 1-0061: Error: firmware xc3028-v27.fw not found. I checked /lib/firmware/ but xc3028-v27.fw is not in the directory ? Must have messed it up somewhere! Any help appreciated. Thanks David ----- Original Message ----- From: "Steven Toth" <stoth@xxxxxxxxxxx> To: "Luke Yelavich" <themuso@xxxxxxxxxxx> Cc: <linux-dvb@xxxxxxxxxxx> Sent: Wednesday, August 06, 2008 11:44 AM Subject: Re: [PATCH] Add initial support for DViCO FusionHDTV DVB-T Dual Express > >>>> I've tested with the HVR1500Q (xc5000 based) and I'm happy with the >>>> results. Can you both try the DViCO board? >>> It tests fine and I like how simpler things have got. >> >> I pulled the above linked tree, and compiled the modules. It seems at the >> moment for the dual express, that I have to pass the parameter card=11 to >> the driver, for it to correctly find the card and make use of all >> adapters. Without any module parameters, dmsg complains that the card >> couldn't be identified, yet two adapters are shown. I have two of these >> cards. >> >> Hope this helps some. > > .. And they're both the same model? > > If so, insert one at a time and run the 'lspci -vn' command, save the > output for each card. > > Post the output here. > > Assuming you load the driver with card=11, does each card work correctly > after that? > > - Steve > > _______________________________________________ > linux-dvb mailing list > linux-dvb@xxxxxxxxxxx > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb > _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
