Hi
timf schrieb:
> Hartmut Hackmann wrote:
>> Hi,
>>
>> timf schrieb:
>>> Hartmut Hackmann wrote:
>>>> Hi, Tim
>>>> <snip>
>>>>>>
>>>>>> I think i know now how your card needs to be configured.
>>>>>> Something that seems not to be really clear for you is the
>>>>>> configuration
>>>>>> of the so-called AGC (automatic gain control) of the tuner. This
>>>>>> needs to be switched according to the function the tuner is used for:
>>>>>> analog TV -> FM Radio -> DVB-T.
>>>>>> This is done with the 4052 analog mux and requires 2 control bits
>>>>>> -> the GPIOs.
>>>>>> GPIO 21 is used to switch between analog TV and FM radio.
>>>>>> Typically GPIO21=0 -> analog TV, GPIO21=1 -> FM Radio.
>>>>>> In your case, GPIO22 is used to switch between DVB-T and analog
>>>>>> while most cards
>>>>>> use GPIO1 of the tda10046 for this.
>>>>>>
>>>>>> You should need to make chages only in saa7134-dvb, dvb_init()
>>>>>> - remove the old
>>>>>> case SAA7134_BOARD_KWORLD_DVBT_210: (plus code)
>>>>>> -and add it to
>>>>>> case SAA7134_BOARD_FLYDVBT_HYBRID_CARDBUS:
>>>>>>
>>>>>> That should do it (though we should add a .antenna switch to the
>>>>>> configuration).
>>>>>>
>>>>>> Best regards
>>>>>> Hartmut
>>>>>>
>>>>> Hi Hartmut,
>>>>>
>>>>>
>>
>> <snip>
>>
>>> Hi Hartmut,
>>>
>>>
>>> 1) With .gpio_config = TDA10046_GP11_I,
>>>
>>> root@ubuntu:/home/timf# tzap -r "TEN HD"
>>> using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
>>> tuning to 788500000 Hz
>>> video pid 0x0202, audio pid 0x0000
>>> status 00 | signal 9d9d | snr 3333 | ber 0001fffe | unc 0000004d |
>>> status 1f | signal 9d9d | snr fdfd | ber 000001b8 | unc ffffffff |
>>> FE_HAS_LOCK
>>> status 1f | signal 9c9c | snr fdfd | ber 000001de | unc 00000000 |
>>> FE_HAS_LOCK
>>> status 1f | signal 9c9c | snr fefe | ber 0000017c | unc 00000000 |
>>> FE_HAS_LOCK
>>> status 1f | signal 9c9c | snr fefe | ber 00000182 | unc 00000000 |
>>> FE_HAS_LOCK
>>> status 1f | signal 9c9c | snr fefe | ber 000001a4 | unc 00000000 |
>>> FE_HAS_LOCK
>>> status 1f | signal 9b9b | snr fefe | ber 00000202 | unc 00000000 |
>>> FE_HAS_LOCK
>>> status 1f | signal 9b9b | snr fefe | ber 0000021c | unc 00000000 |
>>> FE_HAS_LOCK
>>> status 1f | signal 9b9b | snr fefe | ber 00000226 | unc 00000000 |
>>> FE_HAS_LOCK
>>> status 1f | signal 9c9c | snr fefe | ber 00000234 | unc 00000000 |
>>> FE_HAS_LOCK
>>> status 1f | signal 9b9b | snr fefe | ber 00000290 | unc 00000000 |
>>> FE_HAS_LOCK
>>> status 1f | signal 9b9b | snr fefe | ber 00000240 | unc 00000000 |
>>> FE_HAS_LOCK
>>> status 1f | signal 9c9c | snr fefe | ber 000001fa | unc 00000000 |
>>> FE_HAS_LOCK
>>>
>>> Analog-tv also scans fine.
>>>
>>
>> Things should look like this.
>>
>>> 2) With
>>> // .gpio_config = TDA10046_GP11_I,
>>> .gpio_config = TDA10046_GP00_I,
>>>
>>> timf@ubuntu:~$ sudo -s -H
>>> [sudo] password for timf:
>>> root@ubuntu:/home/timf# tzap -r "TEN HD"
>>> using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
>>> tuning to 788500000 Hz
>>> video pid 0x0202, audio pid 0x0000
>>> status 00 | signal 0000 | snr 9494 | ber 0001fffe | unc 00000000 |
>>> status 1f | signal 0000 | snr ecec | ber 00019622 | unc ffffffff |
>>> FE_HAS_LOCK
>>> status 1f | signal 0000 | snr f8f8 | ber 00014eac | unc ffffffff |
>>> FE_HAS_LOCK
>>> status 00 | signal 0000 | snr 5e5e | ber 0001fffe | unc 00000000 |
>>> status 1f | signal 0000 | snr fcfc | ber 00002bcc | unc ffffffff |
>>> FE_HAS_LOCK
>>> status 1f | signal 0000 | snr fdfd | ber 000018a2 | unc 00000000 |
>>> FE_HAS_LOCK
>>> status 1f | signal 0000 | snr fdfd | ber 00000e74 | unc 00000000 |
>>> FE_HAS_LOCK
>>> status 1f | signal 0000 | snr fdfd | ber 00000912 | unc 00000000 |
>>> FE_HAS_LOCK
>>> status 1f | signal 0000 | snr fefe | ber 000006b6 | unc 00000000 |
>>> FE_HAS_LOCK
>>> status 1f | signal 0000 | snr fefe | ber 0000068e | unc 00000000 |
>>> FE_HAS_LOCK
>>> status 1f | signal 0000 | snr fdfd | ber 000005c2 | unc 00000000 |
>>> FE_HAS_LOCK
>>> status 1f | signal 0000 | snr fefe | ber 00000584 | unc 00000000 |
>>> FE_HAS_LOCK
>>>
>>> However, analog-tv fails to scan anything -> "no signal"
>>>
>> This is wrong. Although the channel decoder locks, the signal at its
>> input is very low.
>>
>> But this means: The analog -> dvb switch is the GPIO of the channel
>> decoder
>> *not* GPIO22
>>
>> so we can fix: we need .gpio_config = TDA10046_GP11_I
>>
>>> 3) antenna_switch
>>>
>>> static int philips_tda827x_tuner_init(struct dvb_frontend *fe)
>>> {
>>> struct saa7134_dev *dev = fe->dvb->priv;
>>> struct tda1004x_state *state = fe->demodulator_priv;
>>>
>>> switch (state->config->antenna_switch) {
>>> case 0: break;
>>> case 1: dprintk("setting GPIO21 to 0 (TV antenna?)\n");
>>> saa7134_set_gpio(dev, 21, 0);
>>> break;
>>> case 2: dprintk("setting GPIO21 to 1 (Radio antenna?)\n");
>>> saa7134_set_gpio(dev, 21, 1);
>>> break;
>>> }
>>> return 0;
>>> }
>>>
>>> static int philips_tda827x_tuner_sleep(struct dvb_frontend *fe)
>>> {
>>> struct saa7134_dev *dev = fe->dvb->priv;
>>> struct tda1004x_state *state = fe->demodulator_priv;
>>>
>>> switch (state->config->antenna_switch) {
>>> case 0: break;
>>> case 1: dprintk("setting GPIO21 to 1 (Radio antenna?)\n");
>>> saa7134_set_gpio(dev, 21, 1);
>>> break;
>>> case 2: dprintk("setting GPIO21 to 0 (TV antenna?)\n");
>>> saa7134_set_gpio(dev, 21, 0);
>>> break;
>>> }
>>> return 0;
>>> }
>>>
>>> If I put .antenna_switch = 1 or 2, in my struct, dvb-t fails to scan.
>>> I can't put antenna_switch in my struct, can I, as I am using gpio22?
>>> So I took it out, and in saa7134-cards.c, changed .radio to this:
>>>
>> I don't believe that this is right.
>> It is just a static signal and can't be anything else.
>>
>>> [SAA7134_BOARD_KWORLD_DVBT_210] = {
>>> .name = "KWorld DVB-T 210",
>>> .audio_clock = 0x00187de7,
>>> .tuner_type = TUNER_PHILIPS_TDA8290,
>>> .radio_type = UNSET,
>>> .tuner_addr = ADDR_UNSET,
>>> .radio_addr = ADDR_UNSET,
>>> .mpeg = SAA7134_MPEG_DVB,
>>> .gpiomask = 0 << 21,
>>> .inputs = {{
>>> .name = name_tv,
>>> .vmux = 1,
>>> .amux = TV,
>>> .tv = 1,
>>> },{
>>> .name = name_comp1,
>>> .vmux = 3,
>>> .amux = LINE1,
>>> },{
>>> .name = name_svideo,
>>> .vmux = 8,
>>> .amux = LINE1,
>>> }},
>>> .radio = {
>>> .name = name_radio,
>>> .amux = TV,
>>> .gpio = 0x00000000,
>>
>> This is wrong. It has to be .gpio = 0x0200000, as it was in the original
>> source code.
>>
>>> },
>>> },
>>> I still can't tune to a radio cahnnel.
>>> I'm not sure how to switch to radio, I'm not even sure which gpio
>>> it's on.
>>> I assume it's on gpio21, but I've tried various configs - none work.
>>>
>>> Regards,
>>> Tim
>>>
>> Tim, seriously: For me it looks like you messed up the entire code. I
>> would
>> recommend you roll back completely and start over again.
>>
>>
>> Hartmut
>>
> OK, this is using v4l-dvb as downloaded via mercurial 9 April2008.
> No modifications.
>
> root@ubuntu:/home/timf# tzap -r "TEN HD"
> using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
> tuning to 788500000 Hz
> video pid 0x0202, audio pid 0x0000
> status 00 | signal 9e9e | snr 5d5d | ber 0001fffe | unc 00000000 |
> status 1f | signal 9d9d | snr fdfd | ber 0000010c | unc 00000000 |
> FE_HAS_LOCK
> status 1f | signal 9d9d | snr fefe | ber 00000104 | unc 00000000 |
> FE_HAS_LOCK
> status 1f | signal 9d9d | snr fefe | ber 00000106 | unc 00000000 |
> FE_HAS_LOCK
> status 1f | signal 9d9d | snr fefe | ber 00000116 | unc 00000000 |
> FE_HAS_LOCK
> status 1f | signal 9d9d | snr fefe | ber 0000010e | unc 00000000 |
> FE_HAS_LOCK
> status 1f | signal 9d9d | snr fefe | ber 000000f6 | unc 00000000 |
> FE_HAS_LOCK
> status 1f | signal 9d9d | snr fefe | ber 0000012c | unc 00000000 |
> FE_HAS_LOCK
> status 1f | signal 9d9d | snr fefe | ber 00000108 | unc 00000000 |
> FE_HAS_LOCK
> status 1f | signal 9c9c | snr fefe | ber 0000011e | unc 00000000 |
> FE_HAS_LOCK
> status 1f | signal 9c9c | snr fefe | ber 00000114 | unc 00000000 |
> FE_HAS_LOCK
> status 1f | signal 9d9d | snr fefe | ber 000000f4 | unc 00000000 |
> FE_HAS_LOCK
> status 1f | signal 9c9c | snr fefe | ber 0000010e | unc 00000000 |
> FE_HAS_LOCK
> status 1f | signal 9c9c | snr fefe | ber 0000013a | unc 00000000 |
> FE_HAS_LOCK
> status 1f | signal 9c9c | snr fefe | ber 00000232 | unc 00000000 |
> FE_HAS_LOCK
>
> Analog-tv - "no signal" - no channels scanned
>
> Regards,
> Tim
>
DVB-T works now but not analog? We never had this before.
Just to be sure:
- you are aware that you can't use analog and dvb simultanously?
- you are aware that after stopping a dvb application it takes about a
second before the dvb driver releases the card and the analog tuner can be used?
- did you mix up the antenna inputs?
Hartmut
_______________________________________________
linux-dvb mailing list
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
