timf wrote:
> Hartmut Hackmann wrote:
>
>> Hi, Tim
>>
>> timf schrieb:
>>
>>> hermann pitton wrote:
>>>
>>>> Am Freitag, den 11.04.2008, 00:08 +0200 schrieb Hartmut Hackmann:
>>>>
>>>>
>>>>> HI, Tim
>>>>>
>>>>> timf schrieb:
>>>>>
>>>>>
>>>>>> Hi Hartmut,
>>>>>> OK, found some more spare time, but very, very frustrated!
>>>>>>
>>>>>> 1) Tried ubuntu 7.04, 7.10, 8.04
>>>>>> Tried with just modules that exist in kernel (no v4l-dvb)
>>>>>> Tried v4l-dvb from June 2007 and tried current v4l-dvb
>>>>>> Tried with/without Hartmut patch - changeset 7376 49ba58715fe0
>>>>>> Tried with .gpio_config = TDA10046_GP11_I, or .gpio_config
>>>>>> = TDA10046_GP01_I,
>>>>>> Tried using configs in saa7134-dvb.c matching tiger, tiger_s,
>>>>>> pinnacle 310i, twinhan 3056
>>>>>>
>>>>>> # Australia / Perth (Roleystone transmitter)
>>>>>> # T freq bw fec_hi fec_lo mod transmission-mode guard-interval
>>>>>> hierarchy
>>>>>> # SBS
>>>>>> T 704500000 7MHz 2/3 NONE QAM64 8k 1/8 NONE
>>>>>> # ABC
>>>>>> T 725500000 7MHz 3/4 NONE QAM64 8k 1/16 NONE
>>>>>> # Seven
>>>>>> T 746500000 7MHz 2/3 NONE QAM64 8k 1/16 NONE
>>>>>> # Nine
>>>>>> T 767500000 7MHz 3/4 NONE QAM64 8k 1/16 NONE
>>>>>> # Ten
>>>>>> T 788500000 7MHz 3/4 NONE QAM64 8k 1/16 NONE
>>>>>>
>>>>>> 2) I have these saa7134 cards:
>>>>>> - pinnacle 310i
>>>>>> - kworld 210
>>>>>>
>>>>>> This cx88 card:
>>>>>> - dvico DVB-T Pro hybrid (analog tv not work)
>>>>>>
>>>>>> - problem only occurs with kworld 210 in linux (works fine in
>>>>>> WinXP)
>>>>>>
>>>>>> 3) In WinXP, all channels, both analog tv and dvb-t found
>>>>>>
>>>>>> 4) In linux, if start dvb-t first, never scans SBS - dmesg1
>>>>>>
>>>>>> 5) In linux, if start analog tv first, stop, then start dvb-t,
>>>>>> scan finds SBS - dmesg2
>>>>>>
>>>>>>
>>>>>>
>>>>> a) The pinnacle 310i finds everything?
>>>>> It has the same chipset, but an almost perfectly handled tuner
>>>>> chip...
>>>>> This means that your initial config file is ok...
>>>>> b) Does this mean that in case 4, all other channels are found?
>>>>> c) Case 5: This finds everything?
>>>>> d) What happens if you use the scan data of the pinnacle card?
>>>>> Does it tune SBS? Does it just take more time to stabilize?
>>>>> This can be understood.
>>>>> e) Just to be sure: did you clarify the open point with
>>>>> .antenna_switch
>>>>> (i think so)
>>>>> f) the kernel logs are as expected.
>>>>> <snip>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>> 6) Herman mentioned something called a "mode-switch" in the
>>>>>> archives, but not any description.
>>>>>>
>>>>>>
>>>>> I guess he meant the switching between analog, radio and dvb-t.
>>>>> This is the
>>>>> GPIO handling and card depending.
>>>>>
>>>>>
>>>> Tim must have it from when I mentioned the special case of card=87 and
>>>> 94.
>>>>
>>>>
>>>>
>>>>>> I tried to find some data sheets for tda8275 tda8290 but only
>>>>>> found the publicity pdf file from Phillips,
>>>>>> so at least I can see they go together, so I presume this
>>>>>> "mode-switch" is coded into those modules.
>>>>>> But those modules work for all other cards, so now I'm lost again.
>>>>>>
>>>>>> What else should I try?
>>>>>>
>>>>>>
>>>>>>
>>>>> If my assumptions above are wrong, there is one other chance:
>>>>> Recently i saw another card that does the (unusual) mode switching
>>>>> like card 87. So to be sure, you might try to force this card type (be
>>>>> aware of the antenna inputs, if in doubt, try both.
>>>>>
>>>>> Best regards
>>>>> Hartmut
>>>>>
>>>>>
>>>>>
>>>> For the Medion8800 Quad and CTX948 also showing this issue, needs to
>>>> tune analog first to have good recepton on DVB-T, they are a little
>>>> weaker on analog than other cards, but after that on DVB-T, they are as
>>>> good than known good others.
>>>>
>>>> Cheers,
>>>> Hermann
>>>>
>>>>
>>>>
>>>>
>>> Hi Hartmut and Hermann,
>>>
>>> a) The pinnacle 310i finds everything?
>>> It has the same chipset, but an almost perfectly handled tuner
>>> chip...
>>> This means that your initial config file is ok...
>>>
>>> Answer - Yes, the non-working remote (and constant unknown key
>>> messages) is all that is
>>> wrong with the pinnacle 310i.
>>> I tested it for your new tda8290 tda8275 patches - didn't I send you
>>> the results?
>>> It works fine!
>>>
>>> b) Does this mean that in case 4, all other channels are found?
>>>
>>> Answer - In linux, if start dvb-t first, never scans SBS
>>> - yes all other channels are viewable/scannable.
>>>
>>> c) Case 5: This finds everything?
>>>
>>> Answer - In linux, if start analog tv first, stop, then start dvb-t,
>>> scan finds SBS
>>> - yes all channels are viewable/scannable.
>>>
>>> d) What happens if you use the scan data of the pinnacle card?
>>> Does it tune SBS? Does it just take more time to stabilize?
>>> This can be understood.
>>>
>>> Answer - the same answer applies as for b) and c)
>>>
>>> e) Just to be sure: did you clarify the open point with .antenna_switch
>>> (i think so)
>>>
>>> Answer - yes that was me being over-enthusiastic - made no difference
>>> as you pointed out.
>>>
>>>
>>> OK, this modification has achieved, I think success. I can now
>>> view/scan all channels
>>> in analog tv or dvb-t in either order.
>>> That is, I now don't have to start analog tv first, before dvb-t will
>>> start.
>>>
>>> In saa7134- cards.c - no change.
>>>
>>> In saa7134-dvb.c:
>>>
>>> Remove this:
>>> ------------------------------------
>>> static struct tda1004x_config kworld_dvb_t_210_config = {
>>> .demod_address = 0x08,
>>> .invert = 1,
>>> .invert_oclk = 0,
>>> .xtal_freq = TDA10046_XTAL_16M,
>>> .agc_config = TDA10046_AGC_TDA827X,
>>> .gpio_config = TDA10046_GP11_I,
>>> .if_freq = TDA10046_FREQ_045,
>>> .i2c_gate = 0x4b,
>>> .tuner_address = 0x61,
>>> .antenna_switch= 1,
>>> .request_firmware = philips_tda1004x_request_firmware
>>> };
>>> ------------------------------
>>>
>>> Add this:
>>>
>>> ------------------------------
>>> static int kw210_tuner_init(struct dvb_frontend *fe)
>>> {
>>> struct saa7134_dev *dev = fe->dvb->priv;
>>> philips_tda827x_tuner_init(fe);
>>> /* route TDA8275a AGC input to the channel decoder */
>>> saa7134_set_gpio(dev, 22, 1);
>>> return 0;
>>> }
>>>
>>> static int kw210_tuner_sleep(struct dvb_frontend *fe)
>>> {
>>> struct saa7134_dev *dev = fe->dvb->priv;
>>> /* route TDA8275a AGC input to the analog IF chip*/
>>> saa7134_set_gpio(dev, 22, 0);
>>> philips_tda827x_tuner_sleep(fe);
>>> return 0;
>>> }
>>>
>>> static struct tda827x_config kw210_cfg = {
>>> .tuner_callback = saa7134_tuner_callback,
>>> .init = kw210_tuner_init,
>>> .sleep = kw210_tuner_sleep,
>>> .config = 0
>>> };
>>>
>>> static struct tda1004x_config kworld_dvb_t_210_config = {
>>> .demod_address = 0x08,
>>> .invert = 1,
>>> .invert_oclk = 0,
>>> .xtal_freq = TDA10046_XTAL_16M,
>>> .agc_config = TDA10046_AGC_TDA827X,
>>> .gpio_config = TDA10046_GP11_I,
>>> .if_freq = TDA10046_FREQ_045,
>>> .tuner_address = 0x61,
>>> .request_firmware = philips_tda1004x_request_firmware
>>> };
>>> ----------------------------
>>>
>>> Change this:
>>>
>>> case SAA7134_BOARD_KWORLD_DVBT_210:
>>> dev->dvb.frontend = dvb_attach(tda10046_attach,
>>> &kworld_dvb_t_210_config, &dev->i2c_adap);
>>> if (dev->dvb.frontend) {
>>> if (dvb_attach(tda827x_attach,dev->dvb.frontend,
>>> kworld_dvb_t_210_config.tuner_address, &dev->i2c_adap,
>>> &kw210_cfg) == NULL) {
>>> wprintk("no tda827x tuner found at addr: %02x\n",
>>> kworld_dvb_t_210_config.tuner_address);
>>> }
>>> }
>>> break;
>>> ---------------------------------------------
>>>
>>> However, I need you to explain something for me.
>>>
>>> There is no difference if I use this:
>>>
>>> saa7134_set_gpio(dev, 22, 1);
>>>
>>> or this:
>>>
>>> saa7134_set_gpio(dev, 21, 1);
>>>
>>> I await your guidance, meanwhile I shall apply my
>>> modification to enable the remote and ensure it
>>> doesn't have any effect.
>>>
>>> Many thanks to you both,
>>>
>>> Regards,
>>> Tim
>>>
>>>
>> Again progress, excellent!
>> I think we will need one further interation. If i go through your
>> changes and comments, i come to the opinion that we will get the same
>> with less changes. But if i understand this right, its astonishing
>> that your
>> card worked a bit. But let me go through your last patch again tomorrow -
>> i am too tired now.
>>
>> Best regards
>> Hartmut
>>
>>
> Hi Hartmut,
>
> I was wrong:
>
> ->There is no difference if I use this:
>
> -> saa7134_set_gpio(dev, 22, 1);
>
> ->or this:
>
> -> saa7134_set_gpio(dev, 21, 1);
>
> This is wrong.
> It only works at all when it is this: saa7134_set_gpio(dev, 22, 1);
>
> With this: saa7134_set_gpio(dev, 21, 1); it does not scan anything at all.
>
> I proved this out by modifying the source, rebuild v4l-dvb,
> and then instead of rebooting, I power-cycled each time.
>
>
> There are 2 problems here:
> 1) With no modification, I must switch to analog tv before I can switch
> to dvb-t.
> If I am using Kaffeine, and then wish to use Me-tv, I must view
> analog tv
> in between.
>
> 2) With no modification, dvb-t will not scan SBS unless analog tv viewed
> first.
>
>
> With this modification, both problems vanish.
>
> I have not yet tested radio.
>
> Regards,
> Tim
>
> _______________________________________________
> linux-dvb mailing list
> linux-dvb@xxxxxxxxxxx
> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
>
>
Hi Hartmut,
OK, tried to test radio with gradio, can't get any frequency to lock.
Now, switching to radio then causes analog tv to have a very weak signal
- only 1 channel will scan with very noisy picture.
Then need to power-cycle to revert to good system.
From syslog:
Apr 13 14:15:47 ubuntu kernel: [ 3863.073092] tda829x 0-004b: tda8290
not locked, no signal?
Apr 13 14:15:47 ubuntu kernel: [ 3863.193072] tda829x 0-004b: tda8290
not locked, no signal?
Apr 13 14:15:47 ubuntu kernel: [ 3863.297056] tda829x 0-004b: adjust
gain, step 1. Agc: 0, ADC stat: 0, lock: 0
Apr 13 14:15:47 ubuntu kernel: [ 3863.441033] tda829x 0-004b: adjust
gain, step 2. Agc: 204, lock: 0
Apr 13 14:15:47 ubuntu kernel: [ 3863.585010] tda829x 0-004b: adjust
gain, step 3. Agc: 123
Apr 13 14:15:47 ubuntu kernel: [ 3863.721163] tuner' 0-004b: Cmd
VIDIOC_G_TUNER accepted for radio
Apr 13 14:15:48 ubuntu kernel: [ 3863.737067] tuner' 0-004b: Cmd
VIDIOC_G_TUNER accepted for radio
Apr 13 14:15:48 ubuntu kernel: [ 3863.752986] tuner' 0-004b: Cmd
VIDIOC_S_TUNER accepted for radio
Apr 13 14:15:48 ubuntu kernel: [ 3863.752990] tda829x 0-004b: setting
tda829x to system B
Apr 13 14:15:48 ubuntu kernel: [ 3863.856965] tda827x: setting tda827x
to system B
Apr 13 14:15:48 ubuntu kernel: [ 3863.912956] tda827x: AGC2 gain is: 10
Apr 13 14:15:48 ubuntu kernel: [ 3864.240905] tda829x 0-004b: tda8290
not locked, no signal?
Apr 13 14:15:48 ubuntu kernel: [ 3864.360885] tda829x 0-004b: tda8290
not locked, no signal?
Apr 13 14:15:48 ubuntu kernel: [ 3864.480865] tda829x 0-004b: tda8290
not locked, no signal?
Apr 13 14:15:48 ubuntu kernel: [ 3864.584849] tda829x 0-004b: adjust
gain, step 1. Agc: 0, ADC stat: 0, lock: 0
Apr 13 14:15:48 ubuntu kernel: [ 3864.728828] tda829x 0-004b: adjust
gain, step 2. Agc: 209, lock: 0
Apr 13 14:15:49 ubuntu kernel: [ 3864.872802] tda829x 0-004b: adjust
gain, step 3. Agc: 129
Apr 13 14:17:08 ubuntu kernel: [ 3944.108802] tuner' 0-004b: Cmd
VIDIOC_G_TUNER accepted for radio
Apr 13 14:17:08 ubuntu kernel: [ 3944.132069] tuner' 0-004b: Cmd
VIDIOC_G_TUNER accepted for radio
-> I know the local FM station is 107.3MHz and can tune it in with WinXP
Apr 13 14:17:08 ubuntu kernel: [ 3944.148049] tuner' 0-004b: radio freq
set to 107.30
Apr 13 14:17:08 ubuntu kernel: [ 3944.148054] tda829x 0-004b: setting
tda829x to system B
Apr 13 14:17:08 ubuntu kernel: [ 3944.256024] tda827x: setting tda827x
to system B
Apr 13 14:17:08 ubuntu kernel: [ 3944.324013] tda827x: AGC2 gain is: 10
Apr 13 14:17:08 ubuntu kernel: [ 3944.651961] tda829x 0-004b: tda8290
not locked, no signal?
Apr 13 14:17:09 ubuntu kernel: [ 3944.771941] tda829x 0-004b: tda8290
not locked, no signal?
Apr 13 14:17:09 ubuntu kernel: [ 3944.891922] tda829x 0-004b: tda8290
not locked, no signal?
Apr 13 14:17:09 ubuntu kernel: [ 3944.995906] tda829x 0-004b: adjust
gain, step 1. Agc: 0, ADC stat: 0, lock: 0
Apr 13 14:17:09 ubuntu kernel: [ 3945.143884] tda829x 0-004b: adjust
gain, step 2. Agc: 229, lock: 0
Apr 13 14:17:09 ubuntu kernel: [ 3945.291857] tda829x 0-004b: adjust
gain, step 3. Agc: 149
Apr 13 14:17:09 ubuntu kernel: [ 3945.432058] tuner' 0-004b: Cmd
VIDIOC_G_TUNER accepted for radio
Apr 13 14:17:09 ubuntu kernel: [ 3945.451896] tuner' 0-004b: Cmd
VIDIOC_G_TUNER accepted for radio
Apr 13 14:17:09 ubuntu kernel: [ 3945.467841] tuner' 0-004b: Cmd
VIDIOC_S_TUNER accepted for radio
Apr 13 14:17:09 ubuntu kernel: [ 3945.467845] tda829x 0-004b: setting
tda829x to system B
Apr 13 14:17:09 ubuntu kernel: [ 3945.575812] tda827x: setting tda827x
to system B
Apr 13 14:17:09 ubuntu kernel: [ 3945.643801] tda827x: AGC2 gain is: 10
Apr 13 14:17:10 ubuntu kernel: [ 3945.971749] tda829x 0-004b: tda8290
not locked, no signal?
Apr 13 14:17:10 ubuntu kernel: [ 3946.091729] tda829x 0-004b: tda8290
not locked, no signal?
Apr 13 14:17:10 ubuntu kernel: [ 3946.211710] tda829x 0-004b: tda8290
not locked, no signal?
Apr 13 14:17:10 ubuntu kernel: [ 3946.315694] tda829x 0-004b: adjust
gain, step 1. Agc: 0, ADC stat: 0, lock: 0
Apr 13 14:17:10 ubuntu kernel: [ 3946.463670] tda829x 0-004b: adjust
gain, step 2. Agc: 231, lock: 0
Apr 13 14:17:10 ubuntu kernel: [ 3946.611645] tda829x 0-004b: adjust
gain, step 3. Agc: 150
Apr 13 14:17:20 ubuntu kernel: [ 3956.031282] tuner' 0-004b: Cmd
VIDIOC_G_TUNER accepted for radio
Apr 13 14:17:20 ubuntu kernel: [ 3956.046878] tuner' 0-004b: Cmd
VIDIOC_G_TUNER accepted for radio
So, the radio config isn't correct.
I'll keep digging.
Regards,
Tim
_______________________________________________
linux-dvb mailing list
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
