Manu Abraham wrote: > Per Dal?n wrote: > >> Manu Abraham wrote: >> >> >>> get latest dvb-kernel CVS, compile with 2.6.13, >>> do a modprobe dst verbose=5 >>> >>> or get 2.6.14-rc1 or newer >>> compile and install it, >>> do a modprobe dst verbose=5 >>> >>> and please do send in the logs >>> >>> Manu >>> >>> >>> >> >> >> Ok, thanks for looking into my problems, Manu. >> >> I did some test with 2.6.14-rc1 (no patches and no dvb from cvs). >> I got the same (bad) results (as far as I understand) as with my earlier >> tests. I have described below how I tested and the dmesg from my tests. >> Have I forgotten anything? Do You miss any important log or trace from >> me? >> >> # modprobe bttv i2c_hw=1 card=0x71 >> # modprobe dst verbose=5 >> # modprobe dvb-bt8xx >> >> dmesg: >> ------------------------------------ >> ... >> Linux video capture interface: v1.00 >> bttv: driver version 0.9.16 loaded >> bttv: using 8 buffers with 2080k (520 pages) each for capture >> bttv: Bt8xx card found (0). >> ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [LNKC] -> GSI 11 (level, >> low) -> IRQ 11 >> bttv0: Bt878 (rev 17) at 0000:00:06.0, irq: 11, latency: 32, mmio: >> 0xef000000 >> bttv0: detected: Twinhan VisionPlus DVB [card=113], PCI subsystem ID is >> 1822:0001 >> bttv0: using: Twinhan DST + clones [card=113,insmod option] >> bttv0: gpio: en=00000000, out=00000000 in=00fb00fd [init] >> bttv0: using tuner=4 >> bttv0: add subdevice "dvb0" >> bt878: AUDIO driver version 0.0.0 loaded >> bt878: Bt878 AUDIO function found (0). >> ACPI: PCI Interrupt 0000:00:06.1[A] -> Link [LNKC] -> GSI 11 (level, >> low) -> IRQ 11 >> bt878(0): Bt878 (rev 17) at 00:06.1, irq: 11, latency: 32, memory: >> 0xee800000 >> DVB: registering new adapter (bttv0). >> rdc_8820_reset: Resetting DST >> dst_gpio_outb: mask=[0004], enbb=[0004], outhigh=[0000] >> dst_gpio_outb: mask=[0004], enbb=[0004], outhigh=[0004] >> dst_comm_init: Initializing DST. >> dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] >> rdc_reset_state: Resetting state machine >> dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0000] >> dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0002] >> writing [ 00 06 00 00 00 00 00 fa ] >> dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] >> read_dst: reply is 0xff >> dst_wait_dst_ready: dst wait ready after 1 >> read_dst: reply is 0x0 >> 0x44 0x43 0x54 0x2d 0x43 0x49 0x6c >> dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] >> dst_get_device_id: Recognise [DCT-CI] >> >> >> > >> dst_type_print: DST type: cable >> DST type flags : 0x1 newtuner 0x2 ts204 0x8 firmware version = 1 0x10 >> firmware version = 2 >> dst_comm_init: Initializing DST. >> dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] >> rdc_reset_state: Resetting state machine >> dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0000] >> dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0002] >> writing [ 00 0a 00 00 00 00 00 f6 ] >> dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] >> read_dst: reply is 0xff >> dst_wait_dst_ready: dst wait ready after 0 >> read_dst: reply is 0x0 >> 0x0 0x0 0x0 0x0 0x0 0x0 0x0 >> dst_get_mac: MAC Address=[00:00:00:00:00:00] >> dst_ca_attach: registering DST-CA device >> DVB: registering frontend 0 (DST DVB-C)... >> ------------------------------------ >> >> I use the channel DisMix besauce it is not a scrambled channel. >> >> # ./dvb-apps/util/szap/czap -c mychannels.conf -n 7 -r >> using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' >> reading channels from file 'mychannels.conf' >> 7 DisMix:322000000:INVERSION_AUTO:6875000:FEC_NONE:QAM_64:4100:4356:1016 >> 7 DisMix: f 322000000, s 6875000, i 2, fec 0, qam 3, v 0x1004, a 0x1104 >> status 00 | signal 0000 | snr 0000 | ber 00000004 | unc 00000000 | >> status 1f | signal 8000 | snr 1400 | ber 00000004 | unc 00000000 | >> FE_HAS_LOCK >> status 1f | signal 8000 | snr 1400 | ber 00000004 | unc 00000000 | >> FE_HAS_LOCK >> status 1f | signal 8000 | snr 1400 | ber 00000004 | unc 00000000 | >> FE_HAS_LOCK >> >> >> dmesg: >> ------------------------------------ >> ... >> DVB: registering frontend 0 (DST DVB-C)... >> rdc_8820_reset: Resetting DST >> dst_gpio_outb: mask=[0004], enbb=[0004], outhigh=[0000] >> dst_gpio_outb: mask=[0004], enbb=[0004], outhigh=[0004] >> dst_comm_init: Initializing DST. >> dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] >> rdc_reset_state: Resetting state machine >> dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0000] >> dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0002] >> writing [ 00 06 00 00 00 00 00 fa ] >> dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] >> read_dst: reply is 0xff >> dst_wait_dst_ready: dst wait ready after 1 >> read_dst: reply is 0x0 >> 0x44 0x43 0x54 0x2d 0x43 0x49 0x6c >> dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] >> dst_get_device_id: Recognise [DCT-CI] >> >> >> > > Please check whether your card is a VP-2021 or VP-2031 My card is a VP-2031, at least I think so. It has a text at the back of the card that says "VP20310 V4.0". I took 2 pictures of my card: http://gd-willy.kicks-ass.org/per/dvb-tests/back.jpg http://gd-willy.kicks-ass.org/per/dvb-tests/front.jpg > > >> dst_type_print: DST type: cable >> DST type flags : 0x1 newtuner 0x2 ts204 0x8 firmware version = 1 0x10 >> >> > > If it is a 2031, try changing the dst_tlist[] (for DCT-CI ) > .type_flags = DST_TYPE_HAS_NEWTUNE | DST_TYPE_HAS_FW_2 > only and see what happens. > > with the new dst.ko dmesg: ------------------------------------ ... bttv: driver version 0.9.16 loaded bttv: using 8 buffers with 2080k (520 pages) each for capture bttv: Bt8xx card found (0). ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11 PCI: setting IRQ 11 as level-triggered ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11 bttv0: Bt878 (rev 17) at 0000:00:06.0, irq: 11, latency: 32, mmio: 0xef000000 bttv0: detected: Twinhan VisionPlus DVB [card=113], PCI subsystem ID is 1822:0001 bttv0: using: Twinhan DST + clones [card=113,insmod option] bttv0: gpio: en=00000000, out=00000000 in=00f100fd [init] bttv0: using tuner=4 bttv0: add subdevice "dvb0" bt878: AUDIO driver version 0.0.0 loaded bt878: Bt878 AUDIO function found (0). ACPI: PCI Interrupt 0000:00:06.1[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11 bt878(0): Bt878 (rev 17) at 00:06.1, irq: 11, latency: 32, memory: 0xee800000 DVB: registering new adapter (bttv0). rdc_8820_reset: Resetting DST dst_gpio_outb: mask=[0004], enbb=[0004], outhigh=[0000] dst_gpio_outb: mask=[0004], enbb=[0004], outhigh=[0004] dst_comm_init: Initializing DST. dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] rdc_reset_state: Resetting state machine dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0000] dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0002] writing [ 00 06 00 00 00 00 00 fa ] dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] read_dst: reply is 0xff dst_wait_dst_ready: dst wait ready after 1 read_dst: reply is 0x0 0x44 0x43 0x54 0x2d 0x43 0x49 0x6c dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] dst_get_device_id: Recognise [DCT-CI] dst_type_print: DST type: cable DST type flags : 0x1 newtuner 0x10 firmware version = 2 dst_comm_init: Initializing DST. dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] rdc_reset_state: Resetting state machine dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0000] dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0002] writing [ 00 0a 00 00 00 00 00 f6 ] dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] read_dst: reply is 0xff dst_wait_dst_ready: dst wait ready after 0 read_dst: reply is 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 dst_get_mac: MAC Address=[00:00:00:00:00:00] dst_ca_attach: registering DST-CA device DVB: registering frontend 0 (DST DVB-C)... ------------------------------------ # ./dvb-apps/util/szap/czap -c ~/mychannels.conf -n 7 -r using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' reading channels from file '/root/mychannels.conf' 7 DisMix:322000000:INVERSION_AUTO:6875000:FEC_NONE:QAM_64:4100:4356:1016 7 DisMix: f 322000000, s 6875000, i 2, fec 0, qam 3, v 0x1004, a 0x1104 status 00 | signal 0000 | snr 0000 | ber 00000004 | unc 00000000 | status 1f | signal 8000 | snr 0000 | ber 00000004 | unc 00000000 | FE_HAS_LOCK status 1f | signal 8000 | snr 0000 | ber 00000004 | unc 00000000 | FE_HAS_LOCK status 1f | signal 8000 | snr 0000 | ber 00000004 | unc 00000000 | FE_HAS_LOCK dmesg: ------------------------------------ ... DVB: registering new adapter (bttv0). rdc_8820_reset: Resetting DST dst_gpio_outb: mask=[0004], enbb=[0004], outhigh=[0000] dst_gpio_outb: mask=[0004], enbb=[0004], outhigh=[0004] dst_comm_init: Initializing DST. dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] rdc_reset_state: Resetting state machine dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0000] dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0002] writing [ 00 06 00 00 00 00 00 fa ] dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] read_dst: reply is 0xff dst_wait_dst_ready: dst wait ready after 1 read_dst: reply is 0x0 0x44 0x43 0x54 0x2d 0x43 0x49 0x6c dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] dst_get_device_id: Recognise [DCT-CI] dst_type_print: DST type: cable DST type flags : 0x1 newtuner 0x10 firmware version = 2 dst_comm_init: Initializing DST. dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] rdc_reset_state: Resetting state machine dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0000] dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0002] writing [ 00 0a 00 00 00 00 00 f6 ] dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] read_dst: reply is 0xff dst_wait_dst_ready: dst wait ready after 0 read_dst: reply is 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 dst_get_mac: MAC Address=[00:00:00:00:00:00] dst_ca_attach: registering DST-CA device DVB: registering frontend 0 (DST DVB-C)... dst_set_freq: set Frequency 322000000 dst_set_frontend: Set Frequency=[322000000] dst_set_symbolrate: set symrate 6875000 dst_write_tuna: type_flags 0x11 dst_comm_init: Initializing DST. dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] rdc_reset_state: Resetting state machine dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0000] dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0002] writing [ 09 00 04 e9 d0 00 1a db 40 05 ] dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] read_dst: reply is 0xff dst_wait_dst_ready: dst wait ready after 42 read_dst: reply is 0x9 0x0 0x4 0xe9 0xd0 0x0 0x1a 0xdb 0x40 0x5 dst_comm_init: Initializing DST. dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] rdc_reset_state: Resetting state machine dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0000] dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0002] writing [ 00 05 00 00 00 00 00 fb ] dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] read_dst: reply is 0xff dst_wait_dst_ready: dst wait ready after 1 read_dst: reply is 0x0 0x5 0x0 0x0 0x80 0x2 0x0 0x79 dst_comm_init: Initializing DST. dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] rdc_reset_state: Resetting state machine dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0000] dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0002] writing [ 00 05 00 00 00 00 00 fb ] dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] read_dst: reply is 0xff dst_wait_dst_ready: dst wait ready after 2 read_dst: reply is 0x0 0x5 0x0 0x0 0x80 0x2 0x0 0x79 dst_comm_init: Initializing DST. dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] rdc_reset_state: Resetting state machine dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0000] dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0002] writing [ 00 05 00 00 00 00 00 fb ] dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] read_dst: reply is 0xff dst_wait_dst_ready: dst wait ready after 1 read_dst: reply is 0x0 0x5 0x0 0x0 0x80 0x54 0x0 0x27 dst_comm_init: Initializing DST. dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] rdc_reset_state: Resetting state machine dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0000] dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0002] writing [ 00 05 00 00 00 00 00 fb ] dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] read_dst: reply is 0xff dst_wait_dst_ready: dst wait ready after 1 read_dst: read_dst error (err == -5, len == 0x08, b0 == 0x00) dst_error_recovery: Trying to return from previous errors. dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] read_dst: read_dst error (err == -5, len == 0x08, b0 == 0x00) dst_error_recovery: Trying to return from previous errors. dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] read_dst: RDC 8820 RESET dst_error_bailout: Trying to bailout from previous error. rdc_8820_reset: Resetting DST dst_gpio_outb: mask=[0004], enbb=[0004], outhigh=[0000] dst_gpio_outb: mask=[0004], enbb=[0004], outhigh=[0004] dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] dst_command: Trying to recover.. dst_error_recovery: Trying to return from previous errors. dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] ------------------------------------ # cat /dev/dvb/adapter0/dvr0 > test04.mpeg SUCCESSS!! The file test04.mpeg works and can be found here: http://gd-willy.kicks-ass.org/per/dvb-tests/ Thank you very much Manu for taking time to help me. Regards Per
