Hi Raul, On Thu, 2018-08-23 at 00:58 +0530, Raul Piper wrote: > Hello Inga, > On Tue, Aug 21, 2018 at 10:55 PM Stotland, Inga <inga.stotland@intel. > com> wrote: > > > > Hi Raul, > > > > On Tue, 2018-08-21 at 13:29 +0530, Raul Piper wrote: > > > Hello Inga, > > > > > > > > > On Tue, Aug 21, 2018 at 2:37 AM, Stotland, Inga <inga.stotland@in > > > tel. > > > com> wrote: > > > > Hi Raul, > > > > > > > > On Tue, 2018-08-21 at 01:14 +0530, Raul Piper wrote: > > > > > Hello Inga, > > > > > Attached, > > > > > Rgds, > > > > > Rp > > > > > > > > > > On Tue, Aug 21, 2018 at 12:46 AM, Stotland, Inga > > > > > <inga.stotland@xxxxxxxxx> wrote: > > > > > > Hi Raul, > > > > > > > > > > > > On Tue, 2018-08-21 at 00:13 +0530, Raul Piper wrote: > > > > > > > Hello Inga, > > > > > > > it gives the below logs : > > > > > > > > > > > > > > pi@raspberrypi:~/blueZ $ meshctl -c mesh > > > > > > > > > > > > > > Failed to parse local node configuration file > > > > > > > mesh/local_node.json > > > > > > > > > > > > > > > > > > > > > > > > > > > > pi@raspberrypi:~/blueZ $ meshctl -v > > > > > > > > > > > > > > meshctl: 5.50 > > > > > > > > > > > > > > i need to do export before executing above commands > > > > > > > > > > > > > > pi@raspberrypi:~ $ LD_LIBRARY_PATH=/usr/local/lib > > > > > > > > > > > > > > pi@raspberrypi:~ $ export LD_LIBRARY_PATH > > > > > > > > > > > > > > > > > > > > > > > > > > > > to avoid the below error : > > > > > > > > > > > > > > pi@raspberrypi:~ $ meshctl -v > > > > > > > > > > > > > > meshctl: error while loading shared libraries: libjson- > > > > > > > c.so.4: > > > > > > > cannot > > > > > > > open shared object file: No such file or directory > > > > > > > > > > > > > > > > > > > > > can you please assist? > > > > > > > or any experimental patch I could use on BlueZ > > > > > > > > > > > > > > Thanks in advance > > > > > > > Best Regards, > > > > > > > Rp > > > > > > > > > > > > > > On Mon, Aug 20, 2018 at 3:06 AM, Stotland, Inga > > > > > > > <inga.stotlan > > > > > > > d@in > > > > > > > tel. > > > > > > > com> wrote: > > > > > > > > Hi Raul, > > > > > > > > On Sun, 2018-08-19 at 03:03 +0530, Raul Piper wrote: > > > > > > > > > Hello , > > > > > > > > > I have built and BlueZ 5.50 from the source and > > > > > > > > > installed > > > > > > > > > it > > > > > > > > > on > > > > > > > > > raspberry PI 3 W0, but when I am trying to launch the > > > > > > > > > meshctl > > > > > > > > > tool - > > > > > > > > > using ./meshctl (from within or out side the mesh > > > > > > > > > directory) > > > > > > > > > i am > > > > > > > > > getting the below error : > > > > > > > > > > > > > > > > > > Failed to parse provisioning database file > > > > > > > > > prov_db.json > > > > > > > > > > > > > > > > > > I checked the online sanity onfthe above json file > > > > > > > > > and it > > > > > > > > > seems > > > > > > > > > correct. > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > I tried doing the sudo hcitool -lescan - it shows the > > > > > > > > > LE > > > > > > > > > devices > > > > > > > > > and also > > > > > > > > > > > > > > > > > > bluetoothd -v gives 5.50 which shows my compilation > > > > > > > > > and > > > > > > > > > loading > > > > > > > > > of the > > > > > > > > > new BlueZ is alteast correct. > > > > > > > > > > > > > > > > > > I have already installed the c-json lib . > > > > > > > > > > > > > > > > > > Is this a bug in meshctl? > > > > > > > > > > > > > > > > > > Please assist ! > > > > > > > > > > > > > > > > > > > > > > > > > > > Thanks in Advance ! > > > > > > > > > > > > > > > > Are you using the default json file? If so, there's a > > > > > > > > bug > > > > > > > > in > > > > > > > > meshctl > > > > > > > > for reading from default location (just subimmted a > > > > > > > > patch > > > > > > > > for > > > > > > > > that). > > > > > > > > > > > > > > > > Meanwhile, try running: > > > > > > > > ./meshctl -c mesh > > > > > > > > > > > > > > > > Regards, > > > > > > > > Inga > > > > > > > > > > > > > > > > > > > > I am not an expert on system setup, but could you please > > > > > > run > > > > > > sudo /sbin/ldconfig -v > > > > > > > > > > > > Regards, > > > > > > Inga > > > > > > > > > > > > > > > > > > There is no record of libjson-c in your ldconfig output. So my > > > > guess > > > > would be that something is to do with the installation of json- > > > > c > > > > library on rpi. > > > > > > > > If you had to build the json-c from source and then run make > > > > install, > > > > you may want to modify the installation path to be something > > > > standard > > > > on your system from where ldconfig will be able to pick it up. > > > > ./configure --prefix=/somewhere/not/usr/local prior to make > > > > install > > > > > > > > Alternatively, you may try to run this command: > > > > > > > > ldconfig -l /path-to-libjson-c.so.xxx > > > > > > > > Re-run ldconfig afterwards and see if the libjson-c showed up. > > > > > > > > Regards, > > > > > > > > Inga > > > > > > > > P.S. Just FYI, the standard way to respond to emails on bluez > > > > mailing > > > > list is to include the body of you reply at the tail of the > > > > message. > > > > > > > > > > Sorry for Top posting. > > > I reinstalled the blueZ (with --enable-mesh) , installed json-c > > > from > > > the git > > > I can see the entry of the libjson-c unlike previously but it > > > still > > > gives the same error. > > > > By the same error you mean "error loading shared library" or > > "failed to > > parse"? > > > > > Don't we have to link the libjson-c with the BlueZ while building > > > by > > > setting some Linker flags(LD) in the Makefile of the BlueZ.Is > > > there > > > any such option? > > > How will I come to know that it has built successfully with the > > > reference to the libjson-c. > > > I believe we must have json-c pre-installed before building > > > the BlueZ > > > and Build setup of BlueZ must know where is the libjson-c. > > > > Both configure and Makefile.tools reference ljson-c. meshctl > > executable > > would not be built if libjson-c wasn't found during build time. > > > > In case you are still experiencing "loading shared library" error, > > my > > guess is that the libjson-c location is not on the search path. > > > > Regards, > > Inga > > The error I meant is below (on executing meshctl -c mesh): > "Failed to parse local node configuration file mesh/local_node.json" > > > > ldconfig -v | grep json command gives the below logs : > > ==================== > ldconfig: Path `/lib/arm-linux-gnueabihf' given more than once > > ldconfig: Path `/usr/lib/arm-linux-gnueabihf' given more than once > > libjson-c.so.3 -> libjson-c.so.3.0.1 > > ldconfig: /lib/arm-linux-gnueabihf/ld-2.24.so is the dynamic linker, > ignoring > > > libjson-glib-1.0.so.0 -> libjson-glib-1.0.so.0.200.6 > > libfastjson.so.4 -> libfastjson.so.4.0.0 > > libjson-c.so.4 -> libjson-c.so.4.0.0 > > > > > whereis libjson-c.so.4 gives the below logs : > > =============================== > > libjson-c.so: /usr/local/lib/libjson-c.so /usr/local/lib/libjson- > c.so.4 > > whereis libjson-c.so.4.0.0 gives the below logs : > > ============================== > > libjson-c.so.4.0: /usr/local/lib/libjson-c.so.4.0.0 > > I have added the /usr/local/lib to the PATH > > echo $PATH gives the below logs : > =========================== > /usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/loc > al/games:/usr/games:/usr/local/lib:/home/pi/opt/bin > > > what possibly could be wrong? > Do you have a set of steps to test the "meshctl -c mesh " command > starting from the installation > of json-c and BlueZ . I can start fresh . > > Thanks in advance ! > Rp It seems that now jscon-c library is loaded (otherwise, you would've seen an error "failed to load shared ...") I just realized that you're on 5.50 release. Could you confirm that bluez/mesh directory contains local_node.json & prov_db.json? Simply running "./meshctl" from bluez/mesh directory should work. You can run meshctl from outside mesh directory but then you need to provide -c option, i.e. "-c <path_to_json_files>". Regards, Inga
