Hi Raul, On Tue, 2018-08-21 at 13:29 +0530, Raul Piper wrote: > Hello Inga, > > > On Tue, Aug 21, 2018 at 2:37 AM, Stotland, Inga <inga.stotland@intel. > com> wrote: > > Hi Raul, > > > > On Tue, 2018-08-21 at 01:14 +0530, Raul Piper wrote: > > > Hello Inga, > > > Attached, > > > Rgds, > > > Rp > > > > > > On Tue, Aug 21, 2018 at 12:46 AM, Stotland, Inga > > > <inga.stotland@xxxxxxxxx> wrote: > > > > Hi Raul, > > > > > > > > On Tue, 2018-08-21 at 00:13 +0530, Raul Piper wrote: > > > > > Hello Inga, > > > > > it gives the below logs : > > > > > > > > > > pi@raspberrypi:~/blueZ $ meshctl -c mesh > > > > > > > > > > Failed to parse local node configuration file > > > > > mesh/local_node.json > > > > > > > > > > > > > > > > > > > > pi@raspberrypi:~/blueZ $ meshctl -v > > > > > > > > > > meshctl: 5.50 > > > > > > > > > > i need to do export before executing above commands > > > > > > > > > > pi@raspberrypi:~ $ LD_LIBRARY_PATH=/usr/local/lib > > > > > > > > > > pi@raspberrypi:~ $ export LD_LIBRARY_PATH > > > > > > > > > > > > > > > > > > > > to avoid the below error : > > > > > > > > > > pi@raspberrypi:~ $ meshctl -v > > > > > > > > > > meshctl: error while loading shared libraries: libjson- > > > > > c.so.4: > > > > > cannot > > > > > open shared object file: No such file or directory > > > > > > > > > > > > > > > can you please assist? > > > > > or any experimental patch I could use on BlueZ > > > > > > > > > > Thanks in advance > > > > > Best Regards, > > > > > Rp > > > > > > > > > > On Mon, Aug 20, 2018 at 3:06 AM, Stotland, Inga <inga.stotlan > > > > > d@in > > > > > tel. > > > > > com> wrote: > > > > > > Hi Raul, > > > > > > On Sun, 2018-08-19 at 03:03 +0530, Raul Piper wrote: > > > > > > > Hello , > > > > > > > I have built and BlueZ 5.50 from the source and installed > > > > > > > it > > > > > > > on > > > > > > > raspberry PI 3 W0, but when I am trying to launch the > > > > > > > meshctl > > > > > > > tool - > > > > > > > using ./meshctl (from within or out side the mesh > > > > > > > directory) > > > > > > > i am > > > > > > > getting the below error : > > > > > > > > > > > > > > Failed to parse provisioning database file prov_db.json > > > > > > > > > > > > > > I checked the online sanity onfthe above json file and it > > > > > > > seems > > > > > > > correct. > > > > > > > > > > > > > > > > > > > > > > > > > > > > I tried doing the sudo hcitool -lescan - it shows the LE > > > > > > > devices > > > > > > > and also > > > > > > > > > > > > > > bluetoothd -v gives 5.50 which shows my compilation and > > > > > > > loading > > > > > > > of the > > > > > > > new BlueZ is alteast correct. > > > > > > > > > > > > > > I have already installed the c-json lib . > > > > > > > > > > > > > > Is this a bug in meshctl? > > > > > > > > > > > > > > Please assist ! > > > > > > > > > > > > > > > > > > > > > Thanks in Advance ! > > > > > > > > > > > > Are you using the default json file? If so, there's a bug > > > > > > in > > > > > > meshctl > > > > > > for reading from default location (just subimmted a patch > > > > > > for > > > > > > that). > > > > > > > > > > > > Meanwhile, try running: > > > > > > ./meshctl -c mesh > > > > > > > > > > > > Regards, > > > > > > Inga > > > > > > > > > > > > > > I am not an expert on system setup, but could you please run > > > > sudo /sbin/ldconfig -v > > > > > > > > Regards, > > > > Inga > > > > > > > > > > There is no record of libjson-c in your ldconfig output. So my > > guess > > would be that something is to do with the installation of json-c > > library on rpi. > > > > If you had to build the json-c from source and then run make > > install, > > you may want to modify the installation path to be something > > standard > > on your system from where ldconfig will be able to pick it up. > > ./configure --prefix=/somewhere/not/usr/local prior to make install > > > > Alternatively, you may try to run this command: > > > > ldconfig -l /path-to-libjson-c.so.xxx > > > > Re-run ldconfig afterwards and see if the libjson-c showed up. > > > > Regards, > > > > Inga > > > > P.S. Just FYI, the standard way to respond to emails on bluez > > mailing > > list is to include the body of you reply at the tail of the > > message. > > > > Sorry for Top posting. > I reinstalled the blueZ (with --enable-mesh) , installed json-c from > the git > I can see the entry of the libjson-c unlike previously but it still > gives the same error. By the same error you mean "error loading shared library" or "failed to parse"? > Don't we have to link the libjson-c with the BlueZ while building by > setting some Linker flags(LD) in the Makefile of the BlueZ.Is there > any such option? > How will I come to know that it has built successfully with the > reference to the libjson-c. > I believe we must have json-c pre-installed before building > the BlueZ > and Build setup of BlueZ must know where is the libjson-c. Both configure and Makefile.tools reference ljson-c. meshctl executable would not be built if libjson-c wasn't found during build time. In case you are still experiencing "loading shared library" error, my guess is that the libjson-c location is not on the search path. Regards, Inga
