At Wed, 15 Apr 2009 11:34:23 -0400, Jerry Geis wrote: > > > > Takashi Iwai wrote: > > At Wed, 15 Apr 2009 11:14:20 -0400, > > Jerry Geis wrote: > > > >> > >> Takashi Iwai wrote: > >> > >>> At Wed, 15 Apr 2009 10:45:43 -0400, > >>> Jerry Geis wrote: > >>> > >>> > >>>> Takashi Iwai wrote: > >>>> > >>>> > >>>>> At Wed, 15 Apr 2009 10:00:33 -0400, > >>>>> Jerry Geis wrote: > >>>>> > >>>>> > >>>>> > >>>>>> I am using the gigabyte MA78GM-US2H motherboard. it has the ALC889A audio. > >>>>>> > >>>>>> I am trying 1.0.19 and audio works out the analog back port but not over > >>>>>> HDMI. > >>>>>> > >>>>>> > >>>>>> > >>>>> Never mind about "Function ID" entry. It's just a new line that was > >>>>> added recently. function_id=1 means it's an audio codec. > >>>>> > >>>>> The way HDMI is supported are mainly either through the same audio > >>>>> codec (ALC889A) or through a dedicated HDMI codec. In the former > >>>>> case, you'll likely see a word "HDMI" in the digital output pin of the > >>>>> codec proc file. In the latter case, you must have a different codec > >>>>> chip connected to the HD-audio bus with a different codec address > >>>>> number. > >>>>> > >>>>> > >>>>> Takashi > >>>>> > >>>>> > >>>>> > >>>>> > >>>>> > >>>>>> Codec: Realtek ALC889A > >>>>>> Address: 0 > >>>>>> Function Id: 0x1 > >>>>>> <--------------------------------- this is different > >>>>>> Vendor Id: 0x10ec0885 > >>>>>> Subsystem Id: 0x1458a002 > >>>>>> Revision Id: 0x100101 > >>>>>> No Modem Function Group found > >>>>>> Default PCM: > >>>>>> rates [0x560]: 44100 48000 96000 192000 > >>>>>> bits [0xe]: 16 20 24 > >>>>>> formats [0x1]: PCM > >>>>>> Default Amp-In caps: N/A > >>>>>> Default Amp-Out caps: N/A > >>>>>> GPIO: io=2, o=0, i=0, unsolicited=1, wake=0 > >>>>>> IO[0]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 > >>>>>> IO[1]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 > >>>>>> Node 0x02 [Audio Output] wcaps 0x11: Stereo > >>>>>> Converter: stream=0, channel=0 > >>>>>> PCM: > >>>>>> rates [0x560]: 44100 48000 96000 192000 > >>>>>> bits [0xe]: 16 20 24 > >>>>>> formats [0x1]: PCM > >>>>>> Node 0x03 [Audio Output] wcaps 0x11: Stereo > >>>>>> > >>>>>> I have been looking but havent found a solution yet. I tried grabbing > >>>>>> the snapshot tar ball for today but I get errors on the compile. > >>>>>> > >>>>>> I had a similiar motherboard but it does not report Function ID: 01 : - > >>>>>> HDMI audio on this board works correctly. > >>>>>> Codec: Realtek ALC889A > >>>>>> Address: 0 > >>>>>> Vendor Id: 0x10ec0885 > >>>>>> Subsystem Id: 0x1458a002 > >>>>>> Revision Id: 0x100101 > >>>>>> No Modem Function Group found > >>>>>> Default PCM: > >>>>>> rates [0x560]: 44100 48000 96000 192000 > >>>>>> > >>>>>> Any thoughts???? > >>>>>> > >>>>>> Jerry > >>>>>> _______________________________________________ > >>>>>> Alsa-devel mailing list > >>>>>> Alsa-devel@xxxxxxxxxxxxxxxx > >>>>>> http://mailman.alsa-project.org/mailman/listinfo/alsa-devel > >>>>>> > >>>>>> > >>>>>> > >>>>>> > >>>>> > >>>>> > >>>>> > >>>> I upload alsa-info.sh > >>>> > >>>> for the NOT WORKIng one > >>>> http://www.alsa-project.org/db/?f=7e8bc9485e8bb98bf15dae5a0d5dc038003c3203 > >>>> > >>>> for the working on > >>>> http://www.alsa-project.org/db/?f=a18bcb6e87fe33a7365a749d0877a4546e901bf2 > >>>> > >>>> > >>> How are you testing HDMI output? > >>> > >>> > >>> Takashi > >>> > >>> > >>> > >> I have a sharp aquos HDMI that works with the other motherboard. > >> > >> I am just switching between the two. > >> > >> I have the asound.conf set to the correct hw:X,y on both machines for HDMI. > >> > > > > More exactly? > > > > Also, try like below: > > % aplay -Dhdmi:1 foo.wav > > > > Takashi > > > > > When I run your command : > aplay -Dhdmi:1 /tmp/NewVoiceMale.wav > aplay: main:590: audio open error: Device or resource busy Is /dev/snd/hwC1D*p device being used by some app, such as a sound daemon? Takashi _______________________________________________ Alsa-devel mailing list Alsa-devel@xxxxxxxxxxxxxxxx http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
