Takashi Iwai wrote: > At Wed, 15 Apr 2009 10:45:43 -0400, > Jerry Geis wrote: > >> Takashi Iwai wrote: >> >>> At Wed, 15 Apr 2009 10:00:33 -0400, >>> Jerry Geis wrote: >>> >>> >>>> I am using the gigabyte MA78GM-US2H motherboard. it has the ALC889A audio. >>>> >>>> I am trying 1.0.19 and audio works out the analog back port but not over >>>> HDMI. >>>> >>>> >>> Never mind about "Function ID" entry. It's just a new line that was >>> added recently. function_id=1 means it's an audio codec. >>> >>> The way HDMI is supported are mainly either through the same audio >>> codec (ALC889A) or through a dedicated HDMI codec. In the former >>> case, you'll likely see a word "HDMI" in the digital output pin of the >>> codec proc file. In the latter case, you must have a different codec >>> chip connected to the HD-audio bus with a different codec address >>> number. >>> >>> >>> Takashi >>> >>> >>> >>> >>>> Codec: Realtek ALC889A >>>> Address: 0 >>>> Function Id: 0x1 >>>> <--------------------------------- this is different >>>> Vendor Id: 0x10ec0885 >>>> Subsystem Id: 0x1458a002 >>>> Revision Id: 0x100101 >>>> No Modem Function Group found >>>> Default PCM: >>>> rates [0x560]: 44100 48000 96000 192000 >>>> bits [0xe]: 16 20 24 >>>> formats [0x1]: PCM >>>> Default Amp-In caps: N/A >>>> Default Amp-Out caps: N/A >>>> GPIO: io=2, o=0, i=0, unsolicited=1, wake=0 >>>> IO[0]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 >>>> IO[1]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 >>>> Node 0x02 [Audio Output] wcaps 0x11: Stereo >>>> Converter: stream=0, channel=0 >>>> PCM: >>>> rates [0x560]: 44100 48000 96000 192000 >>>> bits [0xe]: 16 20 24 >>>> formats [0x1]: PCM >>>> Node 0x03 [Audio Output] wcaps 0x11: Stereo >>>> >>>> I have been looking but havent found a solution yet. I tried grabbing >>>> the snapshot tar ball for today but I get errors on the compile. >>>> >>>> I had a similiar motherboard but it does not report Function ID: 01 : - >>>> HDMI audio on this board works correctly. >>>> Codec: Realtek ALC889A >>>> Address: 0 >>>> Vendor Id: 0x10ec0885 >>>> Subsystem Id: 0x1458a002 >>>> Revision Id: 0x100101 >>>> No Modem Function Group found >>>> Default PCM: >>>> rates [0x560]: 44100 48000 96000 192000 >>>> >>>> Any thoughts???? >>>> >>>> Jerry >>>> _______________________________________________ >>>> Alsa-devel mailing list >>>> Alsa-devel@xxxxxxxxxxxxxxxx >>>> http://mailman.alsa-project.org/mailman/listinfo/alsa-devel >>>> >>>> >>>> >>> >>> >> I upload alsa-info.sh >> >> for the NOT WORKIng one >> http://www.alsa-project.org/db/?f=7e8bc9485e8bb98bf15dae5a0d5dc038003c3203 >> >> for the working on >> http://www.alsa-project.org/db/?f=a18bcb6e87fe33a7365a749d0877a4546e901bf2 >> > > How are you testing HDMI output? > > > Takashi > > I have a sharp aquos HDMI that works with the other motherboard. I am just switching between the two. I have the asound.conf set to the correct hw:X,y on both machines for HDMI. Jerry _______________________________________________ Alsa-devel mailing list Alsa-devel@xxxxxxxxxxxxxxxx http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
