At Wed, 15 Apr 2009 11:14:20 -0400, Jerry Geis wrote: > > > > Takashi Iwai wrote: > > At Wed, 15 Apr 2009 10:45:43 -0400, > > Jerry Geis wrote: > > > >> Takashi Iwai wrote: > >> > >>> At Wed, 15 Apr 2009 10:00:33 -0400, > >>> Jerry Geis wrote: > >>> > >>> > >>>> I am using the gigabyte MA78GM-US2H motherboard. it has the ALC889A audio. > >>>> > >>>> I am trying 1.0.19 and audio works out the analog back port but not over > >>>> HDMI. > >>>> > >>>> > >>> Never mind about "Function ID" entry. It's just a new line that was > >>> added recently. function_id=1 means it's an audio codec. > >>> > >>> The way HDMI is supported are mainly either through the same audio > >>> codec (ALC889A) or through a dedicated HDMI codec. In the former > >>> case, you'll likely see a word "HDMI" in the digital output pin of the > >>> codec proc file. In the latter case, you must have a different codec > >>> chip connected to the HD-audio bus with a different codec address > >>> number. > >>> > >>> > >>> Takashi > >>> > >>> > >>> > >>> > >>>> Codec: Realtek ALC889A > >>>> Address: 0 > >>>> Function Id: 0x1 > >>>> <--------------------------------- this is different > >>>> Vendor Id: 0x10ec0885 > >>>> Subsystem Id: 0x1458a002 > >>>> Revision Id: 0x100101 > >>>> No Modem Function Group found > >>>> Default PCM: > >>>> rates [0x560]: 44100 48000 96000 192000 > >>>> bits [0xe]: 16 20 24 > >>>> formats [0x1]: PCM > >>>> Default Amp-In caps: N/A > >>>> Default Amp-Out caps: N/A > >>>> GPIO: io=2, o=0, i=0, unsolicited=1, wake=0 > >>>> IO[0]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 > >>>> IO[1]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 > >>>> Node 0x02 [Audio Output] wcaps 0x11: Stereo > >>>> Converter: stream=0, channel=0 > >>>> PCM: > >>>> rates [0x560]: 44100 48000 96000 192000 > >>>> bits [0xe]: 16 20 24 > >>>> formats [0x1]: PCM > >>>> Node 0x03 [Audio Output] wcaps 0x11: Stereo > >>>> > >>>> I have been looking but havent found a solution yet. I tried grabbing > >>>> the snapshot tar ball for today but I get errors on the compile. > >>>> > >>>> I had a similiar motherboard but it does not report Function ID: 01 : - > >>>> HDMI audio on this board works correctly. > >>>> Codec: Realtek ALC889A > >>>> Address: 0 > >>>> Vendor Id: 0x10ec0885 > >>>> Subsystem Id: 0x1458a002 > >>>> Revision Id: 0x100101 > >>>> No Modem Function Group found > >>>> Default PCM: > >>>> rates [0x560]: 44100 48000 96000 192000 > >>>> > >>>> Any thoughts???? > >>>> > >>>> Jerry > >>>> _______________________________________________ > >>>> Alsa-devel mailing list > >>>> Alsa-devel@xxxxxxxxxxxxxxxx > >>>> http://mailman.alsa-project.org/mailman/listinfo/alsa-devel > >>>> > >>>> > >>>> > >>> > >>> > >> I upload alsa-info.sh > >> > >> for the NOT WORKIng one > >> http://www.alsa-project.org/db/?f=7e8bc9485e8bb98bf15dae5a0d5dc038003c3203 > >> > >> for the working on > >> http://www.alsa-project.org/db/?f=a18bcb6e87fe33a7365a749d0877a4546e901bf2 > >> > > > > How are you testing HDMI output? > > > > > > Takashi > > > > > I have a sharp aquos HDMI that works with the other motherboard. > > I am just switching between the two. > > I have the asound.conf set to the correct hw:X,y on both machines for HDMI. More exactly? Also, try like below: % aplay -Dhdmi:1 foo.wav Takashi _______________________________________________ Alsa-devel mailing list Alsa-devel@xxxxxxxxxxxxxxxx http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
