Hi Ahmad, Thanks to your Mail I tested with barebox_2017.12.0-phy6.bb (thud used barebox_2017.12.0-phy4.bb) and this works in zeus too. > According to the state command output under thud, your state is stored on the EEPROM, not the NAND. Look for update-eeprom in your device tree. > There should also be an /dev/eeprom0.update-eeprom in barebox. That seems right, when working the eeprom is written to on each boot. But I could not find any references to *eep* inside barebox in any layer. > if not, try executing the drvinfo command and see if the driver has probed the EEPROM. > Can you also paste the full barebox output from power-on till failure? Here is the zeus from start: barebox 2019.01.0 #1 Thu Jan 16 12:17:51 UTC 2020 Board: Phytec phyCORE-i.MX6 Quad with NAND detected i.MX6 Quad revision 1.5 i.MX reset reason POR (SRSR: 0x00000001) i.MX6 Quad unique ID: ee803c540f2359d4 mdio_bus: miibus0: probed eth0: got preset MAC address: 50:2d:f4:1b:af:b1 nand: ONFI flash detected nand: NAND device: Manufacturer ID: 0xef, Chip ID: 0xd3 (Winbond W29N08GV), 1024MiB, page size: 2048, OOB size: 64 Bad block table found at page 524224, version 0x01 Bad block table found at page 524160, version 0x01 m25p80 flash@00: n25q128a13 (16384 Kbytes) imx-usb 2184200.usb@xxxxxxxxxx: USB EHCI 1.00 imx-esdhc 2190000.usdhc@xxxxxxxxxx: registered as mmc0 imx-ipuv3 2400000.ipu@xxxxxxxxxx: IPUv3H probed imx-ipuv3 2800000.ipu@xxxxxxxxxx: IPUv3H probed da9063 da90620: da9062 with id 62.22.ff.1a detected netconsole: registered as netconsole-1 phySOM-i.MX6: Using environment in MMC malloc space: 0x2fe7b860 -> 0x4fcf70bf (size 510.5 MiB) mmc0: detected SD card version 2.0 mmc0: registered mmc0 envfs: no envfs (magic mismatch) - envfs never written? running /env/bin/init... Hit m for menu or any other key to stop autoboot: 0 testing for update ubi0: scanning is finished ubi0: registering /dev/nand0.root.ubi ubi0: attached mtd0 (name "nand0.root", size 1019 MiB) to ubi0 ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 ubi0: good PEBs: 8148, bad PEBs: 4, corrupted PEBs: 0 ubi0: user volume: 0, internal volumes: 1, max. volumes count: 128 ubi0: max/mean erase counter: 1/1, WL threshold: 65536, image sequence number: 1694817280 ubi0: available PEBs: 7986, total reserved PEBs: 162, PEBs reserved for bad PEB handling: 156 updating kernel open volume: No such file or directory updating oftree open volume: No such file or directory bootchooser: Cannot get state 'state' Nothing bootable found on 'bootchooser' Nothing bootable found Booting zeus with barebox 2017 it works and looks like that: barebox 2017.12.0 #1 Wed Jan 15 16:36:29 UTC 2020 Board: Phytec phyCORE-i.MX6 Quad with NAND detected i.MX6 Quad revision 1.5 i.MX6 unique ID: ee803c540f2359d4 mdio_bus: miibus0: probed eth0: got preset MAC address: 50:2d:f4:1b:af:b1 nand: ONFI flash detected nand: NAND device: Manufacturer ID: 0xef, Chip ID: 0xd3 (Winbond W29N08GV), 1024MiB, page size: 2048, OOB size: 64 Bad block table found at page 524224, version 0x01 Bad block table found at page 524160, version 0x01 m25p80 flash@00: n25q128a13 (16384 Kbytes) imx-usb 2184200.usb: USB EHCI 1.00 imx-esdhc 2190000.usdhc: registered as 2190000.usdhc da9063 da90620: da9062 with id 62.22.ff.1a detected state: New state registered 'state' state: Using bucket 0@0x00000000 netconsole: registered as netconsole-1 phySOM-i.MX6: Using environment in MMC malloc space: 0x2fefb480 -> 0x4fdf68ff (size 511 MiB) mmc0: detected SD card version 2.0 mmc0: registered mmc0 envfs: no envfs (magic mismatch) - envfs never written? running /env/bin/init... Hit m for menu or any other key to stop autoboot: 0 testing for update ubi0: scanning is finished ubi0 error: ubi_read_volume_table: the layout volume was not found ubi0 error: ubi_attach_mtd_dev: failed to attach mtd0, error -22 failed to attach: Invalid argument updating kernel open volume: No such file or directory updating oftree open volume: No such file or directory booting 'bootchooser' booting 'mmc' So the lines state: New state registered 'state' state: Using bucket 0@0x00000000 are missing in barebox 2019. > Your board should boot normally with upstream barebox, I think. > Can you try and see if v2020.01.0 suffers from the same problem? I do not know yet how to include an upstream package like barebox 2020.01.0. Do I have to rename the old recipe or download the recipe somewhere? Thank you and Best Regards hu -----Original Message----- From: Ahmad Fatoum <a.fatoum@xxxxxxxxxxxxxx> Sent: Wednesday, 15 January 2020 15:37 To: Hans-Ulrich Schlieben <hu.schlieben@xxxxxxxxxxxxxx>; Enrico Joerns <ejo@xxxxxxxxxxxxxx>; yocto@xxxxxxxxxxxxxxxxxxxxxx Cc: barebox@xxxxxxxxxxxxxxxxxxx Subject: Re: [yocto] #yocto bootchooser: Cannot get state 'state' Hello Hans-Ulrich, On 1/15/20 3:25 PM, Hans-Ulrich Schlieben wrote: >> Can you copy the device tree snippet you use for defining state? > Is there a problem because ubi works now and garbles the data in the flash? > >> What does running the state command say? > barebox@Phytec phyCORE-i.MX6 Quad with NAND:/ state registered state > instances: > > is empty in zeus, whereas thud returned: (backend: raw, path: > /dev/eeprom0.update-eeprom) According to the state command output under thud, your state is stored on the EEPROM, not the NAND. Look for update-eeprom in your device tree. There should also be an /dev/eeprom0.update-eeprom in barebox. if not, try executing the drvinfo command and see if the driver has probed the EEPROM. Can you also paste the full barebox output from power-on till failure? Your board should boot normally with upstream barebox, I think. Can you try and see if v2020.01.0 suffers from the same problem? Cheers Ahmad > > Thank you and Regards > > hu > > > -----Original Message----- > From: Ahmad Fatoum <a.fatoum@xxxxxxxxxxxxxx> > Sent: Wednesday, 15 January 2020 14:40 > To: Hans-Ulrich Schlieben <hu.schlieben@xxxxxxxxxxxxxx>; Enrico Joerns > <ejo@xxxxxxxxxxxxxx>; yocto@xxxxxxxxxxxxxxxxxxxxxx > Cc: barebox@xxxxxxxxxxxxxxxxxxx > Subject: Re: [yocto] #yocto bootchooser: Cannot get state 'state' > > On 1/15/20 2:26 PM, Hans-Ulrich Schlieben wrote: >> Hi Enrico, >> >> thank you very much for your help. >> I'm using barebox_2019.01.0-phy4-r7.0 now. In thud I used >> barebox_2017.12.0 The image is built using my own ims layer which >> depends on core-image-minimal LAYERDEPENDS_ims-layer = "core-image-minimal openembedded-layer phytec-layer" >> Its using the meta-phytec Layer and a custom layer from phytec named meta-ksp0663. >> Forgot to mention that rauc is used too, which moved from 1.1 to now 1.2. >> Just changed the LAYERSERIES_COMPAT to "zeus" here to check whether yocto zeus works. >> >> Is there some info what to change in the devicetree and so on when moving to warrior/zeus? >> In thud this worked. > > Are there any other error messages? > Can you copy the device tree snippet you use for defining state? > What does running the state command say? > > (now again, but with CC-list intact) > >> >> Thank you >> Regards >> >> hu >> >>> -----Original Message----- >>> From: Enrico Joerns <ejo@xxxxxxxxxxxxxx> >>> Sent: Wednesday, 15 January 2020 14:03 >>> To: Hans-Ulrich Schlieben <hu.schlieben@xxxxxxxxxxxxxx>; >>> yocto@xxxxxxxxxxxxxxxxxxxxxx >>> Cc: barebox@xxxxxxxxxxxxxxxxxxx >>> Subject: Re: [yocto] #yocto bootchooser: Cannot get state 'state' >>> >>> Hi, >>> >>> this is mainly a barebox-related question, thus I'd suggest asking it on the barebox ML. >>> >>> [cc-ing barebox mailing list] >>> >>> On Wed, 2020-01-15 at 04:10 -0800, hu.schlieben@xxxxxxxxxxxxxx wrote: >>>> Hi, >>>> >>>> booting the new yocto zeus system manually by "boot mmc" works fine >>>> but default bootchooser fails with: >>>> >>>> bootchooser: Cannot get state 'state' >>>> Nothing bootable found on 'bootchooser' >>>> Nothing bootable found >>> >>> Looks like the state node is missing in your device tree. >>> Which version of barebox do you use? >>> And from which layer / recipe? >>> >>>> Building the "same" image in yocto thud works fine. The boot >>>> variables >>>> are: >>>> >>>> * BOOT_system0_.default: 3 >>>> * BOOT_system1_.default: 3 >>>> * allow_color: 0 >>>> * autoboot_timeout: 3 >>>> * boot.default: bootchooser >>>> boot.watchdog_timeout: 0 >>>> bootchooser.default_attempts: 3 >>>> bootchooser.default_priority: 1 >>>> bootchooser.disable_on_zero_attempts: 0 >>>> bootchooser.reset_attempts: (list: "power-on", "all-zero") >>>> bootchooser.reset_priorities: >>>> bootchooser.retry: 0 >>>> * bootchooser.state_prefix: state.bootstate >>>> * bootchooser.system0.boot: mmc >>>> * bootchooser.system0.default_attempts: 3 >>>> * bootchooser.system0.default_priority: 20 >>>> * bootchooser.system1.boot: mmc1 >>>> * bootchooser.system1.default_attempts: 3 >>>> * bootchooser.system1.default_priority: 21 >>>> * bootchooser.targets: system0 system1 >>>> bootm.appendroot: 0 >>>> ... >>>> >>> >>> Regards, Enrico >> >> _______________________________________________ >> barebox mailing list >> barebox@xxxxxxxxxxxxxxxxxxx >> https://eur04.safelinks.protection.outlook.com/?url=http%3A%2F%2Flist >> s >> .infradead.org%2Fmailman%2Flistinfo%2Fbarebox&data=01%7C01%7Chu.s >> c >> hlieben%40codewrights.de%7Cb6b1eddf633845b6004308d799c06b3c%7C0974af9 >> b >> 352b437cb606e9f242c0c227%7C0&sdata=xYCzF1pdhTQArF5%2BHffieEkHNmdq >> X >> w%2BVo2EFWg%2FKOHY%3D&reserved=0 >> > > -- Pengutronix e.K. | | Steuerwalder Str. 21 | https://eur04.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.pengutronix.de%2F&data=01%7C01%7Chu.schlieben%40codewrights.de%7C1257571ee267439a5d2408d799c85393%7C0974af9b352b437cb606e9f242c0c227%7C0&sdata=Z5c4T%2B5MOf1cbFRbqkbdCRgDp2lhJZPWzV9gf3sTDp4%3D&reserved=0 | 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list barebox@xxxxxxxxxxxxxxxxxxx http://lists.infradead.org/mailman/listinfo/barebox
