Hello Hans-Ulrich, On 1/15/20 3:25 PM, Hans-Ulrich Schlieben wrote: >> Can you copy the device tree snippet you use for defining state? > Is there a problem because ubi works now and garbles the data in the flash? > >> What does running the state command say? > barebox@Phytec phyCORE-i.MX6 Quad with NAND:/ state > registered state instances: > > is empty in zeus, whereas thud returned: (backend: raw, path: /dev/eeprom0.update-eeprom) According to the state command output under thud, your state is stored on the EEPROM, not the NAND. Look for update-eeprom in your device tree. There should also be an /dev/eeprom0.update-eeprom in barebox. if not, try executing the drvinfo command and see if the driver has probed the EEPROM. Can you also paste the full barebox output from power-on till failure? Your board should boot normally with upstream barebox, I think. Can you try and see if v2020.01.0 suffers from the same problem? Cheers Ahmad > > Thank you and Regards > > hu > > > -----Original Message----- > From: Ahmad Fatoum <a.fatoum@xxxxxxxxxxxxxx> > Sent: Wednesday, 15 January 2020 14:40 > To: Hans-Ulrich Schlieben <hu.schlieben@xxxxxxxxxxxxxx>; Enrico Joerns <ejo@xxxxxxxxxxxxxx>; yocto@xxxxxxxxxxxxxxxxxxxxxx > Cc: barebox@xxxxxxxxxxxxxxxxxxx > Subject: Re: [yocto] #yocto bootchooser: Cannot get state 'state' > > On 1/15/20 2:26 PM, Hans-Ulrich Schlieben wrote: >> Hi Enrico, >> >> thank you very much for your help. >> I'm using barebox_2019.01.0-phy4-r7.0 now. In thud I used >> barebox_2017.12.0 The image is built using my own ims layer which >> depends on core-image-minimal LAYERDEPENDS_ims-layer = "core-image-minimal openembedded-layer phytec-layer" >> Its using the meta-phytec Layer and a custom layer from phytec named meta-ksp0663. >> Forgot to mention that rauc is used too, which moved from 1.1 to now 1.2. >> Just changed the LAYERSERIES_COMPAT to "zeus" here to check whether yocto zeus works. >> >> Is there some info what to change in the devicetree and so on when moving to warrior/zeus? >> In thud this worked. > > Are there any other error messages? > Can you copy the device tree snippet you use for defining state? > What does running the state command say? > > (now again, but with CC-list intact) > >> >> Thank you >> Regards >> >> hu >> >>> -----Original Message----- >>> From: Enrico Joerns <ejo@xxxxxxxxxxxxxx> >>> Sent: Wednesday, 15 January 2020 14:03 >>> To: Hans-Ulrich Schlieben <hu.schlieben@xxxxxxxxxxxxxx>; >>> yocto@xxxxxxxxxxxxxxxxxxxxxx >>> Cc: barebox@xxxxxxxxxxxxxxxxxxx >>> Subject: Re: [yocto] #yocto bootchooser: Cannot get state 'state' >>> >>> Hi, >>> >>> this is mainly a barebox-related question, thus I'd suggest asking it on the barebox ML. >>> >>> [cc-ing barebox mailing list] >>> >>> On Wed, 2020-01-15 at 04:10 -0800, hu.schlieben@xxxxxxxxxxxxxx wrote: >>>> Hi, >>>> >>>> booting the new yocto zeus system manually by "boot mmc" works fine >>>> but default bootchooser fails with: >>>> >>>> bootchooser: Cannot get state 'state' >>>> Nothing bootable found on 'bootchooser' >>>> Nothing bootable found >>> >>> Looks like the state node is missing in your device tree. >>> Which version of barebox do you use? >>> And from which layer / recipe? >>> >>>> Building the "same" image in yocto thud works fine. The boot >>>> variables >>>> are: >>>> >>>> * BOOT_system0_.default: 3 >>>> * BOOT_system1_.default: 3 >>>> * allow_color: 0 >>>> * autoboot_timeout: 3 >>>> * boot.default: bootchooser >>>> boot.watchdog_timeout: 0 >>>> bootchooser.default_attempts: 3 >>>> bootchooser.default_priority: 1 >>>> bootchooser.disable_on_zero_attempts: 0 >>>> bootchooser.reset_attempts: (list: "power-on", "all-zero") >>>> bootchooser.reset_priorities: >>>> bootchooser.retry: 0 >>>> * bootchooser.state_prefix: state.bootstate >>>> * bootchooser.system0.boot: mmc >>>> * bootchooser.system0.default_attempts: 3 >>>> * bootchooser.system0.default_priority: 20 >>>> * bootchooser.system1.boot: mmc1 >>>> * bootchooser.system1.default_attempts: 3 >>>> * bootchooser.system1.default_priority: 21 >>>> * bootchooser.targets: system0 system1 >>>> bootm.appendroot: 0 >>>> ... >>>> >>> >>> Regards, Enrico >> >> _______________________________________________ >> barebox mailing list >> barebox@xxxxxxxxxxxxxxxxxxx >> https://eur04.safelinks.protection.outlook.com/?url=http%3A%2F%2Flists >> .infradead.org%2Fmailman%2Flistinfo%2Fbarebox&data=01%7C01%7Chu.sc >> hlieben%40codewrights.de%7Cb6b1eddf633845b6004308d799c06b3c%7C0974af9b >> 352b437cb606e9f242c0c227%7C0&sdata=xYCzF1pdhTQArF5%2BHffieEkHNmdqX >> w%2BVo2EFWg%2FKOHY%3D&reserved=0 >> > > -- Pengutronix e.K. | | Steuerwalder Str. 21 | http://www.pengutronix.de/ | 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list barebox@xxxxxxxxxxxxxxxxxxx http://lists.infradead.org/mailman/listinfo/barebox