On Wed, Sep 01, 2010 at 04:16:41AM -0400, Mahmood Naderan wrote: > >sudo /etc/init.d/lm_sensors restart > > mahmood@localhost:~$<mailto:mahmood@localhost:~$> sudo /etc/init.d/lm-sensors restart > .: 39: Can't open /etc/init.d/functions > > Note there is no lm_sensors. I have lm-sensors > I tried /etc/init.d/lm-sensors on a lucid (10.04) system and it works for me. It looks like you overwrote the original version of /etc/init.d/lm-sensors with prog/init.d/lm_sensors. That won't work - prog/init.d/lm_sensors does not work with lucid. You'll need to reinstall the original version of /etc/init.d/lm-sensors and try again. Guenter > // Naderan *Mahmood; > > > ________________________________ > From: Nikola Pajkovsky <npajkovs@xxxxxxxxxx> > To: lm-sensors@xxxxxxxxxxxxxx > Sent: Wed, September 1, 2010 12:41:56 PM > Subject: Re: lmsensors doesn't detect core-i7 sensors > > On 09/01/2010 10:03 AM, Mahmood Naderan wrote: > > >sudo ./sensors-detect > > Yes > > Intel Core family thermal sensor... Success! > > (driver `coretemp') > > ... > > Now follows a summary of the probes I have just done. > > Just press ENTER to continue: > > Driver `it87': > > * ISA bus, address 0x290 > > Chip `ITE IT8720F Super IO Sensors' (confidence: 9) > > Driver `coretemp': > > * Chip `Intel Core family thermal sensor' (confidence: 9) > > Do you want to generate /etc/sysconfig/lm_sensors? (yes/NO): y > > Copy prog/init/lm_sensors.init to /etc/init.d/lm_sensors > > for initialization at boot time. > > You should now start the lm_sensors service to load the required > > kernel modules. > > I then copy that file and restart > > mahmood@localhost:~$ <mailto:mahmood@blackfish:~$> ls /etc/init.d/lm* > > /etc/init.d/lm-sensors > > However this is what I see again > > mahmood@localhost:~$ <mailto:mahmood@localhost:~$> sudo sensors > > it8720-isa-0290 > > Adapter: ISA adapter > > in0: +0.86 V (min = +0.00 V, max = +4.08 V) > > in1: +1.58 V (min = +0.00 V, max = +4.08 V) > > in2: +3.39 V (min = +0.00 V, max = +4.08 V) > > in3: +3.02 V (min = +0.00 V, max = +4.08 V) > > in4: +0.05 V (min = +0.00 V, max = +4.08 V) ALARM > > in5: +3.12 V (min = +0.00 V, max = +4.08 V) > > in6: +0.02 V (min = +0.00 V, max = +4.08 V) ALARM > > in7: +2.16 V (min = +0.00 V, max = +4.08 V) > > Vbat: +3.10 V > > fan1: 1638 RPM (min = 10 RPM) > > fan2: 618 RPM (min = 0 RPM) > > fan3: 1278 RPM (min = 10 RPM) > > fan4: 1203 RPM (min = 0 RPM) > > temp1: +35.0°C (low = +127.0°C, high = +127.0°C) sensor = thermistor > > temp2: +25.0°C (low = +127.0°C, high = +127.0°C) sensor = thermistor > > temp3: +33.0°C (low = +127.0°C, high = +90.0°C) sensor = thermistor > > cpu0_vid: +0.313 V > > No core-i7.... :( > > *// Naderan *Mahmood;* > > > sudo /etc/init.d/lm_sensors restart > > > > > > ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------ ---------------------- > -- > > *From:* Nikola Pajkovsky <npajkovs@xxxxxxxxxx<mailto:npajkovs@xxxxxxxxxx>> > > *To:* lm-sensors@xxxxxxxxxxxxxx<mailto:lm-sensors@xxxxxxxxxxxxxx> > > *Sent:* Wed, September 1, 2010 12:23:10 PM > > *Subject:* Re: lmsensors doesn't detect core-i7 sensors > > > > sudo ./sensors-detect > > > > On 09/01/2010 09:46 AM, Mahmood Naderan wrote: > > > >just svn update # not needed if you have fresh checkout > > > To double check and be sure again: > > > mahmood@localhost:~$ <mailto:mahmood@localhost:~$> svn update 5857 > > > Skipped '5857' > > > > > > Then: > > > > > > > > > mahmood@localhost:~$ <mailto:mahmood@blackfish:~$> cd lm-sensors/prog/detect/ > > > mahmood@localhost:~/lm-sensors/prog/detect$ <mailto:mahmood@blackfish:~/lm-sensors/prog/detect$> sudo sensors-detect > > > # sensors-detect revision 5818 (2010-01-18 17:22:07 +0100) > > > # System: Gigabyte Technology Co., Ltd. P55-USB3 > > > This program will help you determine which kernel modules you need > > > to load to use lm_sensors most effectively. It is generally safe > > > and recommended to accept the default answers to all questions, > > > unless you know what you're doing. > > > Some south bridges, CPUs or memory controllers contain embedded sensors. > > > Do you want to scan for them? This is totally safe. (YES/no): y > > > Silicon Integrated Systems SIS5595... No > > > VIA VT82C686 Integrated Sensors... No > > > VIA VT8231 Integrated Sensors... No > > > AMD K8 thermal sensors... No > > > AMD Family 10h thermal sensors... No > > > AMD Family 11h thermal sensors... No > > > Intel Core family thermal sensor... No > > > Intel Atom thermal sensor... No > > > Intel AMB FB-DIMM thermal sensor... No > > > VIA C7 thermal sensor... No > > > VIA Nano thermal sensor... No > > > Some Super I/O chips contain embedded sensors. We have to write to > > > standard I/O ports to probe them. This is usually safe. > > > Do you want to scan for Super I/O sensors? (YES/no): y > > > Probing for Super-I/O at 0x2e/0x2f > > > Trying family `National Semiconductor'... No > > > Trying family `SMSC'... No > > > Trying family `VIA/Winbond/Nuvoton/Fintek'... No > > > Trying family `ITE'... Yes > > > Found `ITE IT8720F Super IO Sensors' Success! > > > (address 0x290, driver `it87') > > > Probing for Super-I/O at 0x4e/0x4f > > > Trying family `National Semiconductor'... No > > > Trying family `SMSC'... No > > > Trying family `VIA/Winbond/Nuvoton/Fintek'... No > > > Trying family `ITE'... No > > > Some systems (mainly servers) implement IPMI, a set of common interfaces > > > through which system health data may be retrieved, amongst other things. > > > We first try to get the information from SMBIOS. If we don't find it > > > there, we have to read from arbitrary I/O ports to probe for such > > > interfaces. This is normally safe. Do you want to scan for IPMI > > > interfaces? (YES/no): y > > > Probing for `IPMI BMC KCS' at 0xca0... No > > > Probing for `IPMI BMC SMIC' at 0xca8... No > > > Some hardware monitoring chips are accessible through the ISA I/O ports. > > > We have to write to arbitrary I/O ports to probe them. This is usually > > > safe though. Yes, you do have ISA I/O ports even if you do not have any > > > ISA slots! Do you want to scan the ISA I/O ports? (yes/NO): y > > > Probing for `National Semiconductor LM78' at 0x290... No > > > Probing for `National Semiconductor LM79' at 0x290... No > > > Probing for `Winbond W83781D' at 0x290... No > > > Probing for `Winbond W83782D' at 0x290... No > > > Lastly, we can probe the I2C/SMBus adapters for connected hardware > > > monitoring devices. This is the most risky part, and while it works > > > reasonably well on most systems, it has been reported to cause trouble > > > on some systems. > > > Do you want to probe the I2C/SMBus adapters now? (YES/no): y > > > Found unknown SMBus adapter 8086:3b30 at 0000:00:1f.3. > > > Sorry, no supported PCI bus adapters found. > > > Module i2c-dev loaded successfully. > > > Now follows a summary of the probes I have just done. > > > Just press ENTER to continue: > > > Driver `it87': > > > * ISA bus, address 0x290 > > > Chip `ITE IT8720F Super IO Sensors' (confidence: 9) > > > To load everything that is needed, add this to /etc/modules: > > > #----cut here---- > > > # Chip drivers > > > it87 > > > #----cut here---- > > > If you have some drivers built into your kernel, the list above will > > > contain too many modules. Skip the appropriate ones! > > > Do you want to add these lines automatically to /etc/modules? (yes/NO)yes > > > Successful! > > > Monitoring programs won't work until the needed modules are > > > loaded. You may want to run '/etc/init.d/module-init-tools start' > > > to load them. > > > Unloading i2c-dev... OK > > > > > > But that didn't help. See the sensors output: > > > > > > mahmood@localhost:~/lm-sensors/prog/detect$ <mailto:mahmood@blackfish:~/lm-sensors/prog/detect$> sudo sensors > > > it8720-isa-0290 > > > Adapter: ISA adapter > > > in0: +0.86 V (min = +0.00 V, max = +4.08 V) > > > in1: +1.58 V (min = +0.00 V, max = +4.08 V) > > > in2: +3.39 V (min = +0.00 V, max = +4.08 V) > > > in3: +3.02 V (min = +0.00 V, max = +4.08 V) > > > in4: +0.05 V (min = +0.00 V, max = +4.08 V) ALARM > > > in5: +3.12 V (min = +0.00 V, max = +4.08 V) > > > in6: +0.02 V (min = +0.00 V, max = +4.08 V) ALARM > > > in7: +2.16 V (min = +0.00 V, max = +4.08 V) > > > Vbat: +3.10 V > > > fan1: 1683 RPM (min = 10 RPM) > > > fan2: 644 RPM (min = 0 RPM) > > > fan3: 1280 RPM (min = 10 RPM) > > > fan4: 1203 RPM (min = 0 RPM) > > > temp1: +35.0°C (low = +127.0°C, high = +127.0°C) sensor = thermistor > > > temp2: +25.0°C (low = +127.0°C, high = +127.0°C) sensor = thermistor > > > temp3: +33.0°C (low = +127.0°C, high = +90.0°C) sensor = thermistor > > > cpu0_vid: +0.313 V > > > > > > Any idea? Thanks, > > > *// Naderan *Mahmood;* > > > > > > > > > ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------ ------------------ > ---- > > -- > > > *From:* Nikola Pajkovsky <npajkovs@xxxxxxxxxx<mailto:npajkovs@xxxxxxxxxx> <mailto:npajkovs@xxxxxxxxxx<mailto:npajkovs@xxxxxxxxxx>>> > > > *To:* lm-sensors@xxxxxxxxxxxxxx<mailto:lm-sensors@xxxxxxxxxxxxxx> <mailto:lm-sensors@xxxxxxxxxxxxxx<mailto:lm-sensors@xxxxxxxxxxxxxx>> > > > *Sent:* Wed, September 1, 2010 12:08:07 PM > > > *Subject:* Re: lmsensors doesn't detect core-i7 sensors > > > > > > On 09/01/2010 09:30 AM, Mahmood Naderan wrote: > > > > Here is what I did: > > > > mahmood@localhost:~$ <mailto:mahmood@localhost:~$> svn checkout http://lm-sensors.org/svn/lm-sensors/trunk lm-sensors > > > > ... > > > > Checked out revision 5857. > > > Yes > > > > > > > mahmood@localhost:~$ <mailto:mahmood@blackfish:~$> svn update http://lm-sensors.org/svn/lm-sensors/trunk lm-sensors > > > > Skipped 'http://lm-sensors.org/svn/lm-sensors/trunk' > > > > At revision 5857. > > > > Summary of conflicts: > > > > Skipped paths: 1 > > > > Is that what you meant? > > > > *// Naderan *Mahmood;* > > > just svn update # not needed if you have fresh checkout > > > > > > in lm-sensors/prog/detect run sensors-detect and it should find your core-i7 > > > > > > > > > > > > > > > ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------ ---------------- > -- > > ---- > > > -- > > > > *From:* Nikola Pajkovsky <npajkovs@xxxxxxxxxx<mailto:npajkovs@xxxxxxxxxx> <mailto:npajkovs@xxxxxxxxxx<mailto:npajkovs@xxxxxxxxxx>> <mailto:npajkovs@xxxxxxxxxx<mailto:npajkovs@xxxxxxxxxx> <mailto:npajkovs@xxxxxxxxxx<mailto:npajkovs@xxxxxxxxxx>>>> > > > > *To:* lm-sensors@xxxxxxxxxxxxxx<mailto:lm-sensors@xxxxxxxxxxxxxx> <mailto:lm-sensors@xxxxxxxxxxxxxx<mailto:lm-sensors@xxxxxxxxxxxxxx>> <mailto:lm-sensors@xxxxxxxxxxxxxx<mailto:lm-sensors@xxxxxxxxxxxxxx> <mailto:lm-sensors@xxxxxxxxxxxxxx<mailto:lm-sensors@xxxxxxxxxxxxxx>>> > > > > *Sent:* Wed, September 1, 2010 11:49:03 AM > > > > *Subject:* Re: lmsensors doesn't detect core-i7 sensors > > > > > > > > On 09/01/2010 08:38 AM, Mahmood Naderan wrote: > > > > > Dear all, > > > > > > > > > > I ran sensors-detect to detect Core-i7 temperatures but it doesn't show them. Here is the output of sensors-detect: > > > > > > > > > > > > > > > mahmood@localhost:~$ sudo sensors-detect > > > > > # sensors-detect revision 5818 (2010-01-18 17:22:07 +0100) > > > > > # System: Gigabyte Technology Co., Ltd. P55-USB3 > > > > > > > > > > This program will help you determine which kernel modules you need > > > > > to load to use lm_sensors most effectively. It is generally safe > > > > > and recommended to accept the default answers to all questions, > > > > > unless you know what you're doing. > > > > > > > > > > Some south bridges, CPUs or memory controllers contain embedded sensors. > > > > > Do you want to scan for them? This is totally safe. (YES/no): y > > > > > Silicon Integrated Systems SIS5595... No > > > > > VIA VT82C686 Integrated Sensors... No > > > > > VIA VT8231 Integrated Sensors... No > > > > > AMD K8 thermal sensors... No > > > > > AMD Family 10h thermal sensors... No > > > > > AMD Family 11h thermal sensors... No > > > > > Intel Core family thermal sensor... No > > > > > Intel Atom thermal sensor... No > > > > > Intel AMB FB-DIMM thermal sensor... No > > > > > VIA C7 thermal sensor... No > > > > > VIA Nano thermal sensor... No > > > > > > > > > > Some Super I/O chips contain embedded sensors. We have to write to > > > > > standard I/O ports to probe them. This is usually safe. > > > > > Do you want to scan for Super I/O sensors? (YES/no): y > > > > > Probing for Super-I/O at 0x2e/0x2f > > > > > Trying family `National Semiconductor'... No > > > > > Trying family `SMSC'... No > > > > > Trying family `VIA/Winbond/Nuvoton/Fintek'... No > > > > > Trying family `ITE'... Yes > > > > > Found `ITE IT8720F Super IO Sensors' Success! > > > > > (address 0x290, driver `it87') > > > > > Probing for Super-I/O at 0x4e/0x4f > > > > > Trying family `National Semiconductor'... No > > > > > Trying family `SMSC'... No > > > > > Trying family `VIA/Winbond/Nuvoton/Fintek'... No > > > > > Trying family `ITE'... No > > > > > > > > > > Some systems (mainly servers) implement IPMI, a set of common interfaces > > > > > through which system health data may be retrieved, amongst other things. > > > > > We first try to get the information from SMBIOS. If we don't find it > > > > > there, we have to read from arbitrary I/O ports to probe for such > > > > > interfaces. This is normally safe. Do you want to scan for IPMI > > > > > interfaces? (YES/no): y > > > > > Probing for `IPMI BMC KCS' at 0xca0... No > > > > > Probing for `IPMI BMC SMIC' at 0xca8... No > > > > > > > > > > Some hardware monitoring chips are accessible through the ISA I/O ports. > > > > > We have to write to arbitrary I/O ports to probe them. This is usually > > > > > safe though. Yes, you do have ISA I/O ports even if you do not have any > > > > > ISA slots! Do you want to scan the ISA I/O ports? (yes/NO): y > > > > > Probing for `National Semiconductor LM78' at 0x290... No > > > > > Probing for `National Semiconductor LM79' at 0x290... No > > > > > Probing for `Winbond W83781D' at 0x290... No > > > > > Probing for `Winbond W83782D' at 0x290... No > > > > > > > > > > Lastly, we can probe the I2C/SMBus adapters for connected hardware > > > > > monitoring devices. This is the most risky part, and while it works > > > > > reasonably well on most systems, it has been reported to cause trouble > > > > > on some systems. > > > > > Do you want to probe the I2C/SMBus adapters now? (YES/no): y > > > > > Found unknown SMBus adapter 8086:3b30 at 0000:00:1f.3. > > > > > Sorry, no supported PCI bus adapters found. > > > > > Module i2c-dev loaded successfully. > > > > > > > > > > Now follows a summary of the probes I have just done. > > > > > Just press ENTER to continue: > > > > > > > > > > Driver `it87': > > > > > * ISA bus, address 0x290 > > > > > Chip `ITE IT8720F Super IO Sensors' (confidence: 9) > > > > > > > > > > To load everything that is needed, add this to /etc/modules: > > > > > #----cut here---- > > > > > # Chip drivers > > > > > it87 > > > > > #----cut here---- > > > > > If you have some drivers built into your kernel, the list above will > > > > > contain too many modules. Skip the appropriate ones! > > > > > > > > > > Do you want to add these lines automatically to /etc/modules? (yes/NO)yes > > > > > Successful! > > > > > > > > > > Monitoring programs won't work until the needed modules are > > > > > loaded. You may want to run '/etc/init.d/module-init-tools start' > > > > > to load them. > > > > > > > > > > Unloading i2c-dev... OK > > > > > > > > > > > > > > > Then I ran sensors: > > > > > > > > > > mahmood@localhost:~$ sudo sensors > > > > > it8720-isa-0290 > > > > > Adapter: ISA adapter > > > > > in0: +0.86 V (min = +0.00 V, max = +4.08 V) > > > > > in1: +1.58 V (min = +0.00 V, max = +4.08 V) > > > > > in2: +3.39 V (min = +0.00 V, max = +4.08 V) > > > > > in3: +3.02 V (min = +0.00 V, max = +4.08 V) > > > > > in4: +0.05 V (min = +0.00 V, max = +4.08 V) ALARM > > > > > in5: +3.12 V (min = +0.00 V, max = +4.08 V) > > > > > in6: +0.02 V (min = +0.00 V, max = +4.08 V) ALARM > > > > > in7: +2.16 V (min = +0.00 V, max = +4.08 V) > > > > > Vbat: +3.10 V > > > > > fan1: 1679 RPM (min = 10 RPM) > > > > > fan2: 644 RPM (min = 0 RPM) > > > > > fan3: 1278 RPM (min = 10 RPM) > > > > > fan4: 1205 RPM (min = 0 RPM) > > > > > temp1: +36.0°C (low = +127.0°C, high = +127.0°C) sensor = thermistor > > > > > temp2: +25.0°C (low = +127.0°C, high = +127.0°C) sensor = thermistor > > > > > temp3: +33.0°C (low = +127.0°C, high = +90.0°C) sensor = thermistor > > > > > cpu0_vid: +0.313 V > > > > > > > > > > > > > > > What can I do then? currently I have kubuntu 10.04 > > > > > > > > > > *// Naderan *Mahmood;* > > > > > > > > > > > > > > > > > > Pick sensors-detect from svn or file bug against lm-sensors in ubuntu and maintainer(if he is nice) update lm-sensors. > > > > > > > > > > > > _______________________________________________ > lm-sensors mailing list > lm-sensors@xxxxxxxxxxxxxx<mailto:lm-sensors@xxxxxxxxxxxxxx> > http://lists.lm-sensors.org/mailman/listinfo/lm-sensors > > _______________________________________________ > lm-sensors mailing list > lm-sensors@xxxxxxxxxxxxxx > http://lists.lm-sensors.org/mailman/listinfo/lm-sensors _______________________________________________ lm-sensors mailing list lm-sensors@xxxxxxxxxxxxxx http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
