>just svn update # not needed if you have fresh checkout
To double check and be sure again:
To double check and be sure again:
mahmood@localhost:~$ svn update 5857
Skipped '5857'
Skipped '5857'
Then:
mahmood@localhost:~$ cd lm-sensors/prog/detect/
mahmood@localhost:~/lm-sensors/prog/detect$ sudo sensors-detect
# sensors-detect revision 5818 (2010-01-18 17:22:07 +0100)
# System: Gigabyte Technology Co., Ltd. P55-USB3
This program will help you determine which kernel modules you need
to load to use lm_sensors most effectively. It is generally safe
and recommended to accept the default answers to all questions,
unless you know what you're doing.
to load to use lm_sensors most effectively. It is generally safe
and recommended to accept the default answers to all questions,
unless you know what you're doing.
Some south bridges, CPUs or memory controllers contain embedded sensors.
Do you want to scan for them? This is totally safe. (YES/no): y
Silicon Integrated Systems SIS5595... No
VIA VT82C686 Integrated Sensors... No
VIA VT8231 Integrated Sensors... No
AMD K8 thermal sensors... No
AMD Family 10h thermal sensors... No
AMD Family 11h thermal sensors... No
Intel Core family thermal sensor... No
Intel Atom thermal sensor... No
Intel AMB FB-DIMM thermal sensor... No
VIA C7 thermal sensor... No
VIA Nano thermal sensor... No
Do you want to scan for them? This is totally safe. (YES/no): y
Silicon Integrated Systems SIS5595... No
VIA VT82C686 Integrated Sensors... No
VIA VT8231 Integrated Sensors... No
AMD K8 thermal sensors... No
AMD Family 10h thermal sensors... No
AMD Family 11h thermal sensors... No
Intel Core family thermal sensor... No
Intel Atom thermal sensor... No
Intel AMB FB-DIMM thermal sensor... No
VIA C7 thermal sensor... No
VIA Nano thermal sensor... No
Some Super I/O chips contain embedded sensors. We have to write to
standard I/O ports to probe them. This is usually safe.
Do you want to scan for Super I/O sensors? (YES/no): y
Probing for Super-I/O at 0x2e/0x2f
Trying family `National Semiconductor'... No
Trying family `SMSC'... No
Trying family `VIA/Winbond/Nuvoton/Fintek'... No
Trying family `ITE'... Yes
Found `ITE IT8720F Super IO Sensors' Success!
(address 0x290, driver `it87')
Probing for Super-I/O at 0x4e/0x4f
Trying family `National Semiconductor'... No
Trying family `SMSC'... No
Trying family `VIA/Winbond/Nuvoton/Fintek'... No
Trying family `ITE'... No
standard I/O ports to probe them. This is usually safe.
Do you want to scan for Super I/O sensors? (YES/no): y
Probing for Super-I/O at 0x2e/0x2f
Trying family `National Semiconductor'... No
Trying family `SMSC'... No
Trying family `VIA/Winbond/Nuvoton/Fintek'... No
Trying family `ITE'... Yes
Found `ITE IT8720F Super IO Sensors' Success!
(address 0x290, driver `it87')
Probing for Super-I/O at 0x4e/0x4f
Trying family `National Semiconductor'... No
Trying family `SMSC'... No
Trying family `VIA/Winbond/Nuvoton/Fintek'... No
Trying family `ITE'... No
Some systems (mainly servers) implement IPMI, a set of common interfaces
through which system health data may be retrieved, amongst other things.
We first try to get the information from SMBIOS. If we don't find it
there, we have to read from arbitrary I/O ports to probe for such
interfaces. This is normally safe. Do you want to scan for IPMI
interfaces? (YES/no): y
Probing for `IPMI BMC KCS' at 0xca0... No
Probing for `IPMI BMC SMIC' at 0xca8... No
through which system health data may be retrieved, amongst other things.
We first try to get the information from SMBIOS. If we don't find it
there, we have to read from arbitrary I/O ports to probe for such
interfaces. This is normally safe. Do you want to scan for IPMI
interfaces? (YES/no): y
Probing for `IPMI BMC KCS' at 0xca0... No
Probing for `IPMI BMC SMIC' at 0xca8... No
Some hardware monitoring chips are accessible through the ISA I/O ports.
We have to write to arbitrary I/O ports to probe them. This is usually
safe though. Yes, you do have ISA I/O ports even if you do not have any
ISA slots! Do you want to scan the ISA I/O ports? (yes/NO): y
Probing for `National Semiconductor LM78' at 0x290... No
Probing for `National Semiconductor LM79' at 0x290... No
Probing for `Winbond W83781D' at 0x290... No
Probing for `Winbond W83782D' at 0x290... No
We have to write to arbitrary I/O ports to probe them. This is usually
safe though. Yes, you do have ISA I/O ports even if you do not have any
ISA slots! Do you want to scan the ISA I/O ports? (yes/NO): y
Probing for `National Semiconductor LM78' at 0x290... No
Probing for `National Semiconductor LM79' at 0x290... No
Probing for `Winbond W83781D' at 0x290... No
Probing for `Winbond W83782D' at 0x290... No
Lastly, we can probe the I2C/SMBus adapters for connected hardware
monitoring devices. This is the most risky part, and while it works
reasonably well on most systems, it has been reported to cause trouble
on some systems.
Do you want to probe the I2C/SMBus adapters now? (YES/no): y
Found unknown SMBus adapter 8086:3b30 at 0000:00:1f.3.
Sorry, no supported PCI bus adapters found.
Module i2c-dev loaded successfully.
monitoring devices. This is the most risky part, and while it works
reasonably well on most systems, it has been reported to cause trouble
on some systems.
Do you want to probe the I2C/SMBus adapters now? (YES/no): y
Found unknown SMBus adapter 8086:3b30 at 0000:00:1f.3.
Sorry, no supported PCI bus adapters found.
Module i2c-dev loaded successfully.
Now follows a summary of the probes I have just done.
Just press ENTER to continue:
Just press ENTER to continue:
Driver `it87':
* ISA bus, address 0x290
Chip `ITE IT8720F Super IO Sensors' (confidence: 9)
* ISA bus, address 0x290
Chip `ITE IT8720F Super IO Sensors' (confidence: 9)
To load everything that is needed, add this to /etc/modules:
#----cut here----
# Chip drivers
it87
#----cut here----
If you have some drivers built into your kernel, the list above will
contain too many modules. Skip the appropriate ones!
#----cut here----
# Chip drivers
it87
#----cut here----
If you have some drivers built into your kernel, the list above will
contain too many modules. Skip the appropriate ones!
Do you want to add these lines automatically to /etc/modules? (yes/NO)yes
Successful!
Successful!
Monitoring programs won't work until the needed modules are
loaded. You may want to run '/etc/init.d/module-init-tools start'
to load them.
loaded. You may want to run '/etc/init.d/module-init-tools start'
to load them.
Unloading i2c-dev... OK
But that didn't help. See the sensors output:
mahmood@localhost:~/lm-sensors/prog/detect$ sudo sensors
it8720-isa-0290
Adapter: ISA adapter
in0: +0.86 V (min = +0.00 V, max = +4.08 V)
in1: +1.58 V (min = +0.00 V, max = +4.08 V)
in2: +3.39 V (min = +0.00 V, max = +4.08 V)
in3: +3.02 V (min = +0.00 V, max = +4.08 V)
in4: +0.05 V (min = +0.00 V, max = +4.08 V) ALARM
in5: +3.12
V (min = +0.00 V, max = +4.08 V)
in6: +0.02 V (min = +0.00 V, max = +4.08 V) ALARM
in7: +2.16 V (min = +0.00 V, max = +4.08 V)
Vbat: +3.10 V
fan1: 1683 RPM (min = 10 RPM)
fan2: 644 RPM (min = 0 RPM)
fan3: 1280 RPM (min = 10 RPM)
fan4: 1203 RPM (min = 0 RPM)
temp1: +35.0°C (low = +127.0°C, high = +127.0°C) sensor = thermistor
temp2: +25.0°C (low = +127.0°C, high = +127.0°C)
sensor = thermistor
temp3: +33.0°C (low = +127.0°C, high = +90.0°C) sensor = thermistor
cpu0_vid: +0.313 V
Any idea? Thanks,
// Naderan *Mahmood;
From: Nikola Pajkovsky <npajkovs@xxxxxxxxxx>
To: lm-sensors@xxxxxxxxxxxxxx
Sent: Wed, September 1, 2010 12:08:07 PM
Subject: Re: lmsensors doesn't detect core-i7 sensors
On 09/01/2010 09:30 AM, Mahmood Naderan wrote:
> Here is what I did:
> mahmood@localhost:~$ <mailto:mahmood@localhost:~$> svn checkout http://lm-sensors.org/svn/lm-sensors/trunk lm-sensors
> ...
> Checked out revision 5857.
Yes
> mahmood@localhost:~$ <mailto:mahmood@blackfish:~$> svn update http://lm-sensors.org/svn/lm-sensors/trunk lm-sensors
> Skipped 'http://lm-sensors.org/svn/lm-sensors/trunk'
> At revision 5857.
> Summary of conflicts:
> Skipped paths: 1
> Is that what you meant?
> *// Naderan *Mahmood;*
just svn update # not needed if you have fresh checkout
in lm-sensors/prog/detect run sensors-detect and it should find your core-i7
>
>
> ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------ ----------------------
--
> *From:* Nikola Pajkovsky <npajkovs@xxxxxxxxxx>
> *To:* lm-sensors@xxxxxxxxxxxxxx
> *Sent:* Wed, September 1, 2010 11:49:03 AM
> *Subject:* Re: lmsensors doesn't detect core-i7 sensors
>
> On 09/01/2010 08:38 AM, Mahmood Naderan wrote:
> > Dear all,
> >
> > I ran sensors-detect to detect Core-i7 temperatures but it doesn't show them. Here is the output of sensors-detect:
> >
> >
> > mahmood@localhost:~$ sudo sensors-detect
> > # sensors-detect revision 5818 (2010-01-18 17:22:07 +0100)
> > # System: Gigabyte Technology Co., Ltd. P55-USB3
> >
> > This program will help you determine which kernel modules you need
> > to load to use lm_sensors most effectively. It is generally safe
> > and recommended to accept the default answers to all questions,
> > unless you know what you're doing.
> >
> > Some south bridges, CPUs or memory controllers contain embedded sensors.
> > Do you want to scan for them? This is totally safe. (YES/no): y
> > Silicon Integrated Systems SIS5595... No
> > VIA VT82C686 Integrated Sensors... No
> > VIA VT8231 Integrated Sensors... No
> > AMD K8 thermal sensors... No
> > AMD Family 10h thermal sensors... No
> > AMD Family 11h thermal sensors... No
> > Intel Core family thermal sensor... No
> > Intel Atom thermal sensor... No
> > Intel AMB FB-DIMM thermal sensor... No
> > VIA C7 thermal sensor... No
> > VIA Nano thermal sensor... No
> >
> > Some Super I/O chips contain embedded sensors. We have to write to
> > standard I/O ports to probe them. This is usually safe.
> > Do you want to scan for Super I/O sensors? (YES/no): y
> > Probing for Super-I/O at 0x2e/0x2f
> > Trying family `National Semiconductor'... No
> > Trying family `SMSC'... No
> > Trying family `VIA/Winbond/Nuvoton/Fintek'... No
> > Trying family `ITE'... Yes
> > Found `ITE IT8720F Super IO Sensors' Success!
> > (address 0x290, driver `it87')
> > Probing for Super-I/O at 0x4e/0x4f
> > Trying family `National Semiconductor'... No
> > Trying family `SMSC'... No
> > Trying family `VIA/Winbond/Nuvoton/Fintek'... No
> > Trying family `ITE'... No
> >
> > Some systems (mainly servers) implement IPMI, a set of common interfaces
> > through which system health data may be retrieved, amongst other things.
> > We first try to get the information from SMBIOS. If we don't find it
> > there, we have to read from arbitrary I/O ports to probe for such
> > interfaces. This is normally safe. Do you want to scan for IPMI
> > interfaces? (YES/no): y
> > Probing for `IPMI BMC KCS' at 0xca0... No
> > Probing for `IPMI BMC SMIC' at 0xca8... No
> >
> > Some hardware monitoring chips are accessible through the ISA I/O ports.
> > We have to write to arbitrary I/O ports to probe them. This is usually
> > safe though. Yes, you do have ISA I/O ports even if you do not have any
> > ISA slots! Do you want to scan the ISA I/O ports? (yes/NO): y
> > Probing for `National Semiconductor LM78' at 0x290... No
> > Probing for `National Semiconductor LM79' at 0x290... No
> > Probing for `Winbond W83781D' at 0x290... No
> > Probing for `Winbond W83782D' at 0x290... No
> >
> > Lastly, we can probe the I2C/SMBus adapters for connected hardware
> > monitoring devices. This is the most risky part, and while it works
> > reasonably well on most systems, it has been reported to cause trouble
> > on some systems.
> > Do you want to probe the I2C/SMBus adapters now? (YES/no): y
> > Found unknown SMBus adapter 8086:3b30 at 0000:00:1f.3.
> > Sorry, no supported PCI bus adapters found.
> > Module i2c-dev loaded successfully.
> >
> > Now follows a summary of the probes I have just done.
> > Just press ENTER to continue:
> >
> > Driver `it87':
> > * ISA bus, address 0x290
> > Chip `ITE IT8720F Super IO Sensors' (confidence: 9)
> >
> > To load everything that is needed, add this to /etc/modules:
> > #----cut here----
> > # Chip drivers
> > it87
> > #----cut here----
> > If you have some drivers built into your kernel, the list above will
> > contain too many modules. Skip the appropriate ones!
> >
> > Do you want to add these lines automatically to /etc/modules? (yes/NO)yes
> > Successful!
> >
> > Monitoring programs won't work until the needed modules are
> > loaded. You may want to run '/etc/init.d/module-init-tools start'
> > to load them.
> >
> > Unloading i2c-dev... OK
> >
> >
> > Then I ran sensors:
> >
> > mahmood@localhost:~$ sudo sensors
> > it8720-isa-0290
> > Adapter: ISA adapter
> > in0: +0.86 V (min = +0.00 V, max = +4.08 V)
> > in1: +1.58 V (min = +0.00 V, max = +4.08 V)
> > in2: +3.39 V (min = +0.00 V, max = +4.08 V)
> > in3: +3.02 V (min = +0.00 V, max = +4.08 V)
> > in4: +0.05 V (min = +0.00 V, max = +4.08 V) ALARM
> > in5: +3.12 V (min = +0.00 V, max = +4.08 V)
> > in6: +0.02 V (min = +0.00 V, max = +4.08 V) ALARM
> > in7: +2.16 V (min = +0.00 V, max = +4.08 V)
> > Vbat: +3.10 V
> > fan1: 1679 RPM (min = 10 RPM)
> > fan2: 644 RPM (min = 0 RPM)
> > fan3: 1278 RPM (min = 10 RPM)
> > fan4: 1205 RPM (min = 0 RPM)
> > temp1: +36.0°C (low = +127.0°C, high = +127.0°C) sensor = thermistor
> > temp2: +25.0°C (low = +127.0°C, high = +127.0°C) sensor = thermistor
> > temp3: +33.0°C (low = +127.0°C, high = +90.0°C) sensor = thermistor
> > cpu0_vid: +0.313 V
> >
> >
> > What can I do then? currently I have kubuntu 10.04
> >
> > *// Naderan *Mahmood;*
> >
> >
>
> Pick sensors-detect from svn or file bug against lm-sensors in ubuntu and maintainer(if he is nice) update lm-sensors.
>
_______________________________________________
lm-sensors mailing list
lm-sensors@xxxxxxxxxxxxxx
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
_______________________________________________ lm-sensors mailing list lm-sensors@xxxxxxxxxxxxxx http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
