>sudo ./sensors-detect
Yes
Intel Core family thermal sensor... Success!
(driver `coretemp')
...
Intel Core family thermal sensor... Success!
(driver `coretemp')
...
Now follows a summary of the probes I have just done.
Just press ENTER to continue:
Just press ENTER to continue:
Driver `it87':
* ISA bus, address 0x290
Chip `ITE IT8720F Super IO Sensors' (confidence: 9)
* ISA bus, address 0x290
Chip `ITE IT8720F Super IO Sensors' (confidence: 9)
Driver `coretemp':
* Chip `Intel Core family thermal sensor' (confidence: 9)
* Chip `Intel Core family thermal sensor' (confidence: 9)
Do you want to generate /etc/sysconfig/lm_sensors? (yes/NO): y
Copy prog/init/lm_sensors.init to /etc/init.d/lm_sensors
for initialization at boot time.
You should now start the lm_sensors service to load the required
kernel modules.
Copy prog/init/lm_sensors.init to /etc/init.d/lm_sensors
for initialization at boot time.
You should now start the lm_sensors service to load the required
kernel modules.
I then copy that file and restart
However this is what I see again
mahmood@localhost:~$ sudo sensors
it8720-isa-0290
Adapter: ISA adapter
in0: +0.86 V (min = +0.00 V, max = +4.08 V)
in1: +1.58 V (min = +0.00 V, max = +4.08 V)
in2: +3.39 V (min = +0.00 V, max = +4.08 V)
in3: +3.02 V (min = +0.00 V, max = +4.08 V)
in4: +0.05 V (min = +0.00 V, max = +4.08 V) ALARM
in5: +3.12 V (min = +0.00 V, max = +4.08 V)
in6: +0.02 V (min = +0.00 V, max = +4.08 V) ALARM
in7: +2.16 V (min = +0.00 V, max = +4.08 V)
Vbat: +3.10 V
fan1: 1638 RPM (min = 10 RPM)
fan2: 618 RPM (min = 0 RPM)
fan3: 1278 RPM (min = 10 RPM)
fan4: 1203 RPM (min = 0 RPM)
temp1: +35.0°C (low = +127.0°C, high = +127.0°C) sensor = thermistor
temp2: +25.0°C (low = +127.0°C, high = +127.0°C) sensor = thermistor
temp3: +33.0°C (low = +127.0°C, high = +90.0°C) sensor = thermistor
cpu0_vid: +0.313 V
it8720-isa-0290
Adapter: ISA adapter
in0: +0.86 V (min = +0.00 V, max = +4.08 V)
in1: +1.58 V (min = +0.00 V, max = +4.08 V)
in2: +3.39 V (min = +0.00 V, max = +4.08 V)
in3: +3.02 V (min = +0.00 V, max = +4.08 V)
in4: +0.05 V (min = +0.00 V, max = +4.08 V) ALARM
in5: +3.12 V (min = +0.00 V, max = +4.08 V)
in6: +0.02 V (min = +0.00 V, max = +4.08 V) ALARM
in7: +2.16 V (min = +0.00 V, max = +4.08 V)
Vbat: +3.10 V
fan1: 1638 RPM (min = 10 RPM)
fan2: 618 RPM (min = 0 RPM)
fan3: 1278 RPM (min = 10 RPM)
fan4: 1203 RPM (min = 0 RPM)
temp1: +35.0°C (low = +127.0°C, high = +127.0°C) sensor = thermistor
temp2: +25.0°C (low = +127.0°C, high = +127.0°C) sensor = thermistor
temp3: +33.0°C (low = +127.0°C, high = +90.0°C) sensor = thermistor
cpu0_vid: +0.313 V
No core-i7.... :(
// Naderan *Mahmood;
From: Nikola Pajkovsky <npajkovs@xxxxxxxxxx>
To: lm-sensors@xxxxxxxxxxxxxx
Sent: Wed, September 1, 2010 12:23:10 PM
Subject: Re: lmsensors doesn't detect core-i7 sensors
sudo ./sensors-detect
On 09/01/2010 09:46 AM, Mahmood Naderan wrote:
> >just svn update # not needed if you have fresh checkout
> To double check and be sure again:
> mahmood@localhost:~$ <mailto:mahmood@localhost:~$> svn update 5857
> Skipped '5857'
>
> Then:
>
>
> mahmood@localhost:~$ <mailto:mahmood@blackfish:~$> cd lm-sensors/prog/detect/
> mahmood@localhost:~/lm-sensors/prog/detect$ <mailto:mahmood@blackfish:~/lm-sensors/prog/detect$> sudo sensors-detect
> # sensors-detect revision 5818 (2010-01-18 17:22:07 +0100)
> # System: Gigabyte Technology Co., Ltd. P55-USB3
> This program will help you determine which kernel modules you need
> to load to use lm_sensors most effectively. It is generally safe
> and recommended to accept the default answers to all questions,
> unless you know what you're doing.
> Some south bridges, CPUs or memory controllers contain embedded sensors.
> Do you want to scan for them? This is totally safe. (YES/no): y
> Silicon Integrated Systems SIS5595... No
> VIA VT82C686 Integrated Sensors... No
> VIA VT8231 Integrated Sensors... No
> AMD K8 thermal sensors... No
> AMD Family 10h thermal sensors... No
> AMD Family 11h thermal sensors... No
> Intel Core family thermal sensor... No
> Intel Atom thermal sensor... No
> Intel AMB FB-DIMM thermal sensor... No
> VIA C7 thermal sensor... No
> VIA Nano thermal sensor... No
> Some Super I/O chips contain embedded sensors. We have to write to
> standard I/O ports to probe them. This is usually safe.
> Do you want to scan for Super I/O sensors? (YES/no): y
> Probing for Super-I/O at 0x2e/0x2f
> Trying family `National Semiconductor'... No
> Trying family `SMSC'... No
> Trying family `VIA/Winbond/Nuvoton/Fintek'... No
> Trying family `ITE'... Yes
> Found `ITE IT8720F Super IO Sensors' Success!
> (address 0x290, driver `it87')
> Probing for Super-I/O at 0x4e/0x4f
> Trying family `National Semiconductor'... No
> Trying family `SMSC'... No
> Trying family `VIA/Winbond/Nuvoton/Fintek'... No
> Trying family `ITE'... No
> Some systems (mainly servers) implement IPMI, a set of common interfaces
> through which system health data may be retrieved, amongst other things.
> We first try to get the information from SMBIOS. If we don't find it
> there, we have to read from arbitrary I/O ports to probe for such
> interfaces. This is normally safe. Do you want to scan for IPMI
> interfaces? (YES/no): y
> Probing for `IPMI BMC KCS' at 0xca0... No
> Probing for `IPMI BMC SMIC' at 0xca8... No
> Some hardware monitoring chips are accessible through the ISA I/O ports.
> We have to write to arbitrary I/O ports to probe them. This is usually
> safe though. Yes, you do have ISA I/O ports even if you do not have any
> ISA slots! Do you want to scan the ISA I/O ports? (yes/NO): y
> Probing for `National Semiconductor LM78' at 0x290... No
> Probing for `National Semiconductor LM79' at 0x290... No
> Probing for `Winbond W83781D' at 0x290... No
> Probing for `Winbond W83782D' at 0x290... No
> Lastly, we can probe the I2C/SMBus adapters for connected hardware
> monitoring devices. This is the most risky part, and while it works
> reasonably well on most systems, it has been reported to cause trouble
> on some systems.
> Do you want to probe the I2C/SMBus adapters now? (YES/no): y
> Found unknown SMBus adapter 8086:3b30 at 0000:00:1f.3.
> Sorry, no supported PCI bus adapters found.
> Module i2c-dev loaded successfully.
> Now follows a summary of the probes I have just done.
> Just press ENTER to continue:
> Driver `it87':
> * ISA bus, address 0x290
> Chip `ITE IT8720F Super IO Sensors' (confidence: 9)
> To load everything that is needed, add this to /etc/modules:
> #----cut here----
> # Chip drivers
> it87
> #----cut here----
> If you have some drivers built into your kernel, the list above will
> contain too many modules. Skip the appropriate ones!
> Do you want to add these lines automatically to /etc/modules? (yes/NO)yes
> Successful!
> Monitoring programs won't work until the needed modules are
> loaded. You may want to run '/etc/init.d/module-init-tools start'
> to load them.
> Unloading i2c-dev... OK
>
> But that didn't help. See the sensors output:
>
> mahmood@localhost:~/lm-sensors/prog/detect$ <mailto:mahmood@blackfish:~/lm-sensors/prog/detect$> sudo sensors
> it8720-isa-0290
> Adapter: ISA adapter
> in0: +0.86 V (min = +0.00 V, max = +4.08 V)
> in1: +1.58 V (min = +0.00 V, max = +4.08 V)
> in2: +3.39 V (min = +0.00 V, max = +4.08 V)
> in3: +3.02 V (min = +0.00 V, max = +4.08 V)
> in4: +0.05 V (min = +0.00 V, max = +4.08 V) ALARM
> in5: +3.12 V (min = +0.00 V, max = +4.08 V)
> in6: +0.02 V (min = +0.00 V, max = +4.08 V) ALARM
> in7: +2.16 V (min = +0.00 V, max = +4.08 V)
> Vbat: +3.10 V
> fan1: 1683 RPM (min = 10 RPM)
> fan2: 644 RPM (min = 0 RPM)
> fan3: 1280 RPM (min = 10 RPM)
> fan4: 1203 RPM (min = 0 RPM)
> temp1: +35.0°C (low = +127.0°C, high = +127.0°C) sensor = thermistor
> temp2: +25.0°C (low = +127.0°C, high = +127.0°C) sensor = thermistor
> temp3: +33.0°C (low = +127.0°C, high = +90.0°C) sensor = thermistor
> cpu0_vid: +0.313 V
>
> Any idea? Thanks,
> *// Naderan *Mahmood;*
>
>
> ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------ ----------------------
--
> *From:* Nikola Pajkovsky <npajkovs@xxxxxxxxxx>
> *To:* lm-sensors@xxxxxxxxxxxxxx
> *Sent:* Wed, September 1, 2010 12:08:07 PM
> *Subject:* Re: lmsensors doesn't detect core-i7 sensors
>
> On 09/01/2010 09:30 AM, Mahmood Naderan wrote:
> > Here is what I did:
> > mahmood@localhost:~$ <mailto:mahmood@localhost:~$> svn checkout http://lm-sensors.org/svn/lm-sensors/trunk lm-sensors
> > ...
> > Checked out revision 5857.
> Yes
>
> > mahmood@localhost:~$ <mailto:mahmood@blackfish:~$> svn update http://lm-sensors.org/svn/lm-sensors/trunk lm-sensors
> > Skipped 'http://lm-sensors.org/svn/lm-sensors/trunk'
> > At revision 5857.
> > Summary of conflicts:
> > Skipped paths: 1
> > Is that what you meant?
> > *// Naderan *Mahmood;*
> just svn update # not needed if you have fresh checkout
>
> in lm-sensors/prog/detect run sensors-detect and it should find your core-i7
>
> >
> >
> > ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------ ------------------
----
> --
> > *From:* Nikola Pajkovsky <npajkovs@xxxxxxxxxx <mailto:npajkovs@xxxxxxxxxx>>
> > *To:* lm-sensors@xxxxxxxxxxxxxx <mailto:lm-sensors@xxxxxxxxxxxxxx>
> > *Sent:* Wed, September 1, 2010 11:49:03 AM
> > *Subject:* Re: lmsensors doesn't detect core-i7 sensors
> >
> > On 09/01/2010 08:38 AM, Mahmood Naderan wrote:
> > > Dear all,
> > >
> > > I ran sensors-detect to detect Core-i7 temperatures but it doesn't show them. Here is the output of sensors-detect:
> > >
> > >
> > > mahmood@localhost:~$ sudo sensors-detect
> > > # sensors-detect revision 5818 (2010-01-18 17:22:07 +0100)
> > > # System: Gigabyte Technology Co., Ltd. P55-USB3
> > >
> > > This program will help you determine which kernel modules you need
> > > to load to use lm_sensors most effectively. It is generally safe
> > > and recommended to accept the default answers to all questions,
> > > unless you know what you're doing.
> > >
> > > Some south bridges, CPUs or memory controllers contain embedded sensors.
> > > Do you want to scan for them? This is totally safe. (YES/no): y
> > > Silicon Integrated Systems SIS5595... No
> > > VIA VT82C686 Integrated Sensors... No
> > > VIA VT8231 Integrated Sensors... No
> > > AMD K8 thermal sensors... No
> > > AMD Family 10h thermal sensors... No
> > > AMD Family 11h thermal sensors... No
> > > Intel Core family thermal sensor... No
> > > Intel Atom thermal sensor... No
> > > Intel AMB FB-DIMM thermal sensor... No
> > > VIA C7 thermal sensor... No
> > > VIA Nano thermal sensor... No
> > >
> > > Some Super I/O chips contain embedded sensors. We have to write to
> > > standard I/O ports to probe them. This is usually safe.
> > > Do you want to scan for Super I/O sensors? (YES/no): y
> > > Probing for Super-I/O at 0x2e/0x2f
> > > Trying family `National Semiconductor'... No
> > > Trying family `SMSC'... No
> > > Trying family `VIA/Winbond/Nuvoton/Fintek'... No
> > > Trying family `ITE'... Yes
> > > Found `ITE IT8720F Super IO Sensors' Success!
> > > (address 0x290, driver `it87')
> > > Probing for Super-I/O at 0x4e/0x4f
> > > Trying family `National Semiconductor'... No
> > > Trying family `SMSC'... No
> > > Trying family `VIA/Winbond/Nuvoton/Fintek'... No
> > > Trying family `ITE'... No
> > >
> > > Some systems (mainly servers) implement IPMI, a set of common interfaces
> > > through which system health data may be retrieved, amongst other things.
> > > We first try to get the information from SMBIOS. If we don't find it
> > > there, we have to read from arbitrary I/O ports to probe for such
> > > interfaces. This is normally safe. Do you want to scan for IPMI
> > > interfaces? (YES/no): y
> > > Probing for `IPMI BMC KCS' at 0xca0... No
> > > Probing for `IPMI BMC SMIC' at 0xca8... No
> > >
> > > Some hardware monitoring chips are accessible through the ISA I/O ports.
> > > We have to write to arbitrary I/O ports to probe them. This is usually
> > > safe though. Yes, you do have ISA I/O ports even if you do not have any
> > > ISA slots! Do you want to scan the ISA I/O ports? (yes/NO): y
> > > Probing for `National Semiconductor LM78' at 0x290... No
> > > Probing for `National Semiconductor LM79' at 0x290... No
> > > Probing for `Winbond W83781D' at 0x290... No
> > > Probing for `Winbond W83782D' at 0x290... No
> > >
> > > Lastly, we can probe the I2C/SMBus adapters for connected hardware
> > > monitoring devices. This is the most risky part, and while it works
> > > reasonably well on most systems, it has been reported to cause trouble
> > > on some systems.
> > > Do you want to probe the I2C/SMBus adapters now? (YES/no): y
> > > Found unknown SMBus adapter 8086:3b30 at 0000:00:1f.3.
> > > Sorry, no supported PCI bus adapters found.
> > > Module i2c-dev loaded successfully.
> > >
> > > Now follows a summary of the probes I have just done.
> > > Just press ENTER to continue:
> > >
> > > Driver `it87':
> > > * ISA bus, address 0x290
> > > Chip `ITE IT8720F Super IO Sensors' (confidence: 9)
> > >
> > > To load everything that is needed, add this to /etc/modules:
> > > #----cut here----
> > > # Chip drivers
> > > it87
> > > #----cut here----
> > > If you have some drivers built into your kernel, the list above will
> > > contain too many modules. Skip the appropriate ones!
> > >
> > > Do you want to add these lines automatically to /etc/modules? (yes/NO)yes
> > > Successful!
> > >
> > > Monitoring programs won't work until the needed modules are
> > > loaded. You may want to run '/etc/init.d/module-init-tools start'
> > > to load them.
> > >
> > > Unloading i2c-dev... OK
> > >
> > >
> > > Then I ran sensors:
> > >
> > > mahmood@localhost:~$ sudo sensors
> > > it8720-isa-0290
> > > Adapter: ISA adapter
> > > in0: +0.86 V (min = +0.00 V, max = +4.08 V)
> > > in1: +1.58 V (min = +0.00 V, max = +4.08 V)
> > > in2: +3.39 V (min = +0.00 V, max = +4.08 V)
> > > in3: +3.02 V (min = +0.00 V, max = +4.08 V)
> > > in4: +0.05 V (min = +0.00 V, max = +4.08 V) ALARM
> > > in5: +3.12 V (min = +0.00 V, max = +4.08 V)
> > > in6: +0.02 V (min = +0.00 V, max = +4.08 V) ALARM
> > > in7: +2.16 V (min = +0.00 V, max = +4.08 V)
> > > Vbat: +3.10 V
> > > fan1: 1679 RPM (min = 10 RPM)
> > > fan2: 644 RPM (min = 0 RPM)
> > > fan3: 1278 RPM (min = 10 RPM)
> > > fan4: 1205 RPM (min = 0 RPM)
> > > temp1: +36.0°C (low = +127.0°C, high = +127.0°C) sensor = thermistor
> > > temp2: +25.0°C (low = +127.0°C, high = +127.0°C) sensor = thermistor
> > > temp3: +33.0°C (low = +127.0°C, high = +90.0°C) sensor = thermistor
> > > cpu0_vid: +0.313 V
> > >
> > >
> > > What can I do then? currently I have kubuntu 10.04
> > >
> > > *// Naderan *Mahmood;*
> > >
> > >
> >
> > Pick sensors-detect from svn or file bug against lm-sensors in ubuntu and maintainer(if he is nice) update lm-sensors.
> >
>
_______________________________________________
lm-sensors mailing list
lm-sensors@xxxxxxxxxxxxxx
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
_______________________________________________ lm-sensors mailing list lm-sensors@xxxxxxxxxxxxxx http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
