Hi folks, over the past two weeks, I've worked on the dwc2 driver to make it work on the RT3052 platform. Basic mass-storage works, there are still some unsolved problems with 3G modems I haven't looked at closely yet. During that time, I've done some cleanups and small fixes whenever I noticed something in the code, and this patch series is the result. A lot of these patches are probably ok to apply as-is, but some of might need some modifications. It has become a bit of big patch series, but because there are a lot of small dependencies between patches, I decided to just send it over as a single series. There roughly three big changes: register-related cleanups, fixing an irq race condition and irq related cleanups, and adding a platform driver. These are register-related and misc cleanups: staging: dwc2: when dma is disabled, clear dev->dma_mask staging: dwc2: disable dma when no dma_mask was setup staging: dwc2: fix naming of register constants staging: dwc2: fix off-by-one in check for max_packet_count parameter staging: dwc2: replace some magic numbers by constants staging: dwc2: remove unneeded check staging: dwc2: use dwc2_hcd_get_frame_number where possible staging: dwc2: add helper variable to simplify code staging: dwc2: unshift non-bool register value constants staging: dwc2: only read the snpsid register once staging: dwc2: remove some device-mode related debug code staging: dwc2: simplify register shift expressions staging: dwc2: add missing shift staging: dwc2: simplify debug output in dwc_hc_init staging: dwc2: re-use hptxfsiz variable staging: dwc2: remove redundant register reads staging: dwc2: properly mask the GRXFSIZ register staging: dwc2: interpret all hwcfg and related register at init time staging: dwc2: validate the value for phy_utmi_width staging: dwc2: make dwc2_core_params documentation more complete These are irq cleanups and the last one is the fix: staging: dwc2: do not use IRQF_DISABLED staging: dwc2: do not handle PRTINT in dwc2_handle_common_intr staging: dwc2: move some interrupt enabling around staging: dwc2: disable I2CINT in dwc2_disable_host_interrupts staging: dwc2: add dwc2_disable_common_interrupts function staging: dwc2: introduce GINTMSK_HOST macro staging: dwc2: use functions to disable interrupts staging: dwc2: properly separate common and host interrupt enabling staging: dwc2: don't pass IRQ_LEVEL to devm_request_irq staging: dwc2: register common irq handler in dwc2_core_init These are platform-driver related: staging: dwc2: convert to devm_ioremap_resource() staging: dwc2: cleanup includes in pci.c staging: dwc2: set the driver name to "dwc2" staging: dwc2: Make dwc2_set_uninitialized more specific staging: dwc2: add platform device bindings staging: dwc2: load parameters from the devicetree And these patch are just for reference. I'll send the MIPS patches to the MIPS folks later, the raspberry pi patch isn't quite working yet. MIPS: ralink: use the dwc2 driver for the rt305x USB controller MIPS: ralink: setup dma_mask for the rt305x dwc2 usb controller WIP: enable dwc2 for raspberry pi Stephen Warren (2): staging: dwc2: add const to handling of dwc2_core_params staging: dwc2: use irq_return_t for interrupt handlers Documentation/devicetree/bindings/staging/dwc2.txt | 51 ++ arch/arm/Kconfig | 1 + arch/arm/boot/dts/bcm2835.dtsi | 6 + arch/arm/configs/bcm2835_defconfig | 20 +- arch/mips/ralink/dts/rt3050.dtsi | 2 +- arch/mips/ralink/rt305x-usb.c | 5 + drivers/staging/dwc2/Kconfig | 6 +- drivers/staging/dwc2/Makefile | 2 + drivers/staging/dwc2/core.c | 522 ++++++++++++--------- drivers/staging/dwc2/core.h | 198 ++++++-- drivers/staging/dwc2/core_intr.c | 32 +- drivers/staging/dwc2/hcd.c | 204 +++----- drivers/staging/dwc2/hcd.h | 30 +- drivers/staging/dwc2/hcd_ddma.c | 8 +- drivers/staging/dwc2/hcd_intr.c | 88 ++-- drivers/staging/dwc2/hcd_queue.c | 2 +- drivers/staging/dwc2/hw.h | 147 +++--- drivers/staging/dwc2/pci.c | 24 +- drivers/staging/dwc2/platform.c | 218 +++++++++ 19 files changed, 997 insertions(+), 569 deletions(-) create mode 100644 Documentation/devicetree/bindings/staging/dwc2.txt create mode 100644 drivers/staging/dwc2/platform.c -- 1.8.0 -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
