Hi, On Mittwoch, 19. März 2008, Tejun Heo wrote: > Tejun Heo wrote: > Just in case, here's the updated patch. I tried your patch (on freshly unpacked sources). non-raid setting in bios, coldboot: [ 37.123980] ahci 0000:00:0a.0: version 3.0 [ 37.124155] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 23 [ 37.124199] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LSA0] -> GSI 23 (level, low) -> IRQ 23 [ 37.124533] ahci 0000:00:0a.0: controller can't do PMP, turning off CAP_PMP [ 38.124731] ahci 0000:00:0a.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl IDE mode [ 38.124780] ahci 0000:00:0a.0: flags: 64bit sntf led clo pio [ 38.124819] PCI: Setting latency timer of device 0000:00:0a.0 to 64 [ 38.125020] scsi0 : ahci [ 38.125116] scsi1 : ahci [ 38.125182] scsi2 : ahci [ 38.125248] scsi3 : ahci [ 38.125337] ata1: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc100 irq 315 [ 38.125384] ata2: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc180 irq 315 [ 38.125432] ata3: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc200 irq 315 [ 38.125479] ata4: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc280 irq 315 [ 38.597035] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 38.597732] ata1.00: ATA-7: WDC WD1600JS-00MHB1, 10.02E01, max UDMA/133 [ 38.597775] ata1.00: 312581808 sectors, multi 16: LBA48 [ 38.598405] ata1.00: configured for UDMA/133 [ 39.069342] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 39.084225] ata2.00: ATA-8: SAMSUNG HD501LJ, CR100-12, max UDMA7 [ 39.084264] ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32) [ 39.086268] ata2.00: configured for UDMA/133 [ 39.405277] ata3: SATA link down (SStatus 0 SControl 300) [ 39.724583] ata4: SATA link down (SStatus 0 SControl 300) [ 39.724672] scsi 0:0:0:0: Direct-Access ATA WDC WD1600JS-00M 10.0 PQ: 0 ANSI: 5 [ 39.724782] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB) [ 39.724826] sd 0:0:0:0: [sda] Write Protect is off [ 39.724864] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 39.724872] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 39.724942] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB) [ 39.724985] sd 0:0:0:0: [sda] Write Protect is off [ 39.725023] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 39.725030] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 39.725079] sda: sda1 sda2 sda3 sda4 < sda5 sda6 > [ 39.763787] sd 0:0:0:0: [sda] Attached SCSI disk [ 39.763923] scsi 1:0:0:0: Direct-Access ATA SAMSUNG HD501LJ CR10 PQ: 0 ANSI: 5 [ 39.764032] sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) [ 39.764077] sd 1:0:0:0: [sdb] Write Protect is off [ 39.764115] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 39.764124] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 39.764194] sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) [ 39.764237] sd 1:0:0:0: [sdb] Write Protect is off [ 39.764275] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 39.764283] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 39.764332] sdb: sdb1 sdb2 [ 39.793043] sd 1:0:0:0: [sdb] Attached SCSI disk reboot: [ 39.522696] ahci 0000:00:0a.0: version 3.0 [ 39.522871] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 23 [ 39.522914] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LSA0] -> GSI 23 (level, low) -> IRQ 23 [ 39.523247] ahci 0000:00:0a.0: controller can't do PMP, turning off CAP_PMP [ 40.523447] ahci 0000:00:0a.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl IDE mode [ 40.523496] ahci 0000:00:0a.0: flags: 64bit sntf led clo pio [ 40.523535] PCI: Setting latency timer of device 0000:00:0a.0 to 64 [ 40.523737] scsi0 : ahci [ 40.523832] scsi1 : ahci [ 40.523898] scsi2 : ahci [ 40.523964] scsi3 : ahci [ 40.524053] ata1: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc100 irq 315 [ 40.524100] ata2: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc180 irq 315 [ 40.524148] ata3: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc200 irq 315 [ 40.524195] ata4: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc280 irq 315 [ 40.995751] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 40.996374] ata1.00: ATA-7: WDC WD1600JS-00MHB1, 10.02E01, max UDMA/133 [ 40.996416] ata1.00: 312581808 sectors, multi 16: LBA48 [ 40.997049] ata1.00: configured for UDMA/133 [ 41.468058] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 41.471873] ata2.00: ATA-8: SAMSUNG HD501LJ, CR100-12, max UDMA7 [ 41.471913] ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32) [ 41.473917] ata2.00: configured for UDMA/133 [ 41.790689] ata3: SATA link down (SStatus 0 SControl 300) [ 42.109995] ata4: SATA link down (SStatus 0 SControl 300) [ 42.110084] scsi 0:0:0:0: Direct-Access ATA WDC WD1600JS-00M 10.0 PQ: 0 ANSI: 5 [ 42.110194] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB) [ 42.110238] sd 0:0:0:0: [sda] Write Protect is off [ 42.110276] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 42.110284] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 42.110354] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB) [ 42.110397] sd 0:0:0:0: [sda] Write Protect is off [ 42.110435] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 42.110442] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 42.110492] sda: sda1 sda2 sda3 sda4 < sda5 sda6 > [ 42.140153] sd 0:0:0:0: [sda] Attached SCSI disk [ 42.140289] scsi 1:0:0:0: Direct-Access ATA SAMSUNG HD501LJ CR10 PQ: 0 ANSI: 5 [ 42.140398] sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) [ 42.140443] sd 1:0:0:0: [sdb] Write Protect is off [ 42.140481] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 42.140489] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 42.140559] sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) [ 42.140602] sd 1:0:0:0: [sdb] Write Protect is off [ 42.140639] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 42.140647] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 42.140696] sdb: sdb1 sdb2 [ 42.167607] sd 1:0:0:0: [sdb] Attached SCSI disk Full dmesgs attached. Glück Auf Volker
[ 0.000000] Linux version 2.6.24.3reiser4ahci_no_srst (root@energy) (gcc version 4.2.3 (Gentoo 4.2.3 p1.0)) #1 SMP Wed Mar 19 07:57:35 CET 2008 [ 0.000000] Command line: root=/dev/sda3 nmi_watchdog=0 console=tty6 [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000e6000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 00000000cffb0000 (usable) [ 0.000000] BIOS-e820: 00000000cffb0000 - 00000000cffc0000 (ACPI data) [ 0.000000] BIOS-e820: 00000000cffc0000 - 00000000cfff0000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000cfff0000 - 00000000d0000000 (reserved) [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved) [ 0.000000] BIOS-e820: 00000000ff380000 - 0000000100000000 (reserved) [ 0.000000] BIOS-e820: 0000000100000000 - 0000000130000000 (usable) [ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 256 used [ 0.000000] Entering add_active_range(0, 256, 851888) 1 entries of 256 used [ 0.000000] Entering add_active_range(0, 1048576, 1245184) 2 entries of 256 used [ 0.000000] end_pfn_map = 1245184 [ 0.000000] DMI present. [ 0.000000] ACPI: RSDP 000F98E0, 0014 (r0 ACPIAM) [ 0.000000] ACPI: RSDT CFFB0000, 003C (r1 A M I OEMRSDT 12000731 MSFT 97) [ 0.000000] ACPI: FACP CFFB0200, 0084 (r2 A_M_I OEMFACP 12000601 MSFT 97) [ 0.000000] ACPI: DSDT CFFB0450, 4FFA (r1 ASR19 ASR19186 186 INTL 20051117) [ 0.000000] ACPI: FACS CFFC0000, 0040 [ 0.000000] ACPI: APIC CFFB0390, 0080 (r1 A M I OEMAPIC 12000731 MSFT 97) [ 0.000000] ACPI: MCFG CFFB0410, 003C (r1 A M I OEMMCFG 12000731 MSFT 97) [ 0.000000] ACPI: OEMB CFFC0040, 0060 (r1 A M I AMI_OEM 12000731 MSFT 97) [ 0.000000] ACPI: HPET CFFB5450, 0038 (r1 A M I OEMHPET0 12000731 MSFT 97) [ 0.000000] ACPI: SSDT CFFB5490, 030E (r1 A M I POWERNOW 1 AMD 1) [ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 256 used [ 0.000000] Entering add_active_range(0, 256, 851888) 1 entries of 256 used [ 0.000000] Entering add_active_range(0, 1048576, 1245184) 2 entries of 256 used [ 0.000000] No mptable found. [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] DMA32 4096 -> 1048576 [ 0.000000] Normal 1048576 -> 1245184 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[3] active PFN ranges [ 0.000000] 0: 0 -> 159 [ 0.000000] 0: 256 -> 851888 [ 0.000000] 0: 1048576 -> 1245184 [ 0.000000] On node 0 totalpages: 1048399 [ 0.000000] DMA zone: 56 pages used for memmap [ 0.000000] DMA zone: 853 pages reserved [ 0.000000] DMA zone: 3090 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 14280 pages used for memmap [ 0.000000] DMA32 zone: 833512 pages, LIFO batch:31 [ 0.000000] Normal zone: 2688 pages used for memmap [ 0.000000] Normal zone: 193920 pages, LIFO batch:31 [ 0.000000] Movable zone: 0 pages used for memmap [ 0.000000] ACPI: PM-Timer IO Port: 0x2008 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) [ 0.000000] Processor #0 (Bootup-CPU) [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) [ 0.000000] Processor #1 [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled) [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] ACPI: IRQ14 used by override. [ 0.000000] ACPI: IRQ15 used by override. [ 0.000000] Setting APIC routing to flat [ 0.000000] ACPI: HPET id: 0x10de8201 base: 0xfed00000 [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000 [ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e6000 [ 0.000000] swsusp: Registered nosave memory region: 00000000000e6000 - 0000000000100000 [ 0.000000] swsusp: Registered nosave memory region: 00000000cffb0000 - 00000000cffc0000 [ 0.000000] swsusp: Registered nosave memory region: 00000000cffc0000 - 00000000cfff0000 [ 0.000000] swsusp: Registered nosave memory region: 00000000cfff0000 - 00000000d0000000 [ 0.000000] swsusp: Registered nosave memory region: 00000000d0000000 - 00000000fec00000 [ 0.000000] swsusp: Registered nosave memory region: 00000000fec00000 - 00000000fec01000 [ 0.000000] swsusp: Registered nosave memory region: 00000000fec01000 - 00000000fee00000 [ 0.000000] swsusp: Registered nosave memory region: 00000000fee00000 - 00000000fef00000 [ 0.000000] swsusp: Registered nosave memory region: 00000000fef00000 - 00000000ff380000 [ 0.000000] swsusp: Registered nosave memory region: 00000000ff380000 - 0000000100000000 [ 0.000000] Allocating PCI resources starting at d4000000 (gap: d0000000:2ec00000) [ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs [ 0.000000] PERCPU: Allocating 31408 bytes of per cpu data [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1030522 [ 0.000000] Kernel command line: root=/dev/sda3 nmi_watchdog=0 console=tty6 [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes) [ 0.000000] hpet clockevent registered [ 0.000000] TSC calibrated against HPET [ 36.691985] Marking TSC unstable due to TSCs unsynchronized [ 36.691986] time.c: Detected 3013.887 MHz processor. [ 36.695815] Console: colour VGA+ 80x25 [ 36.695817] console [tty6] enabled [ 36.700423] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 36.702652] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 36.703423] Checking aperture... [ 36.703461] CPU 0: aperture @ ecc8000000 size 32 MB [ 36.703499] Aperture too small (32 MB) [ 36.709379] No AGP bridge found [ 36.709415] Your BIOS doesn't leave a aperture memory hole [ 36.709453] Please enable the IOMMU option in the BIOS setup [ 36.709491] This costs you 64 MB of RAM [ 36.734719] Mapping aperture over 65536 KB of RAM @ 8000000 [ 36.758840] Memory: 4049948k/4980736k available (2192k kernel code, 143428k reserved, 681k data, 176k init) [ 36.758909] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1 [ 36.841634] Calibrating delay using timer specific routine.. 6034.68 BogoMIPS (lpj=10053897) [ 36.841727] Mount-cache hash table entries: 256 [ 36.841834] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 36.841873] CPU: L2 Cache: 1024K (64 bytes/line) [ 36.841912] CPU: Physical Processor ID: 0 [ 36.841948] CPU: Processor Core ID: 0 [ 36.842001] SMP alternatives: switching to UP code [ 36.842364] ACPI: Core revision 20070126 [ 36.877541] Using local APIC timer interrupts. [ 36.910685] APIC timer calibration result 12557870 [ 36.910686] Detected 12.557 MHz APIC timer. [ 36.910772] SMP alternatives: switching to SMP code [ 36.911002] Booting processor 1/2 APIC 0x1 [ 36.921189] Initializing CPU#1 [ 37.003951] Calibrating delay using timer specific routine.. 6030.92 BogoMIPS (lpj=10046282) [ 37.003956] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 37.003957] CPU: L2 Cache: 1024K (64 bytes/line) [ 37.003959] CPU: Physical Processor ID: 0 [ 37.003960] CPU: Processor Core ID: 1 [ 37.004041] AMD Athlon(tm) 64 X2 Dual Core Processor 6000+ stepping 03 [ 37.004029] Brought up 2 CPUs [ 37.004487] net_namespace: 120 bytes [ 37.004718] NET: Registered protocol family 16 [ 37.004831] ACPI: bus type pci registered [ 37.004913] PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved [ 37.004952] PCI: Not using MMCONFIG. [ 37.004989] PCI: Using configuration type 1 [ 37.007230] ACPI: EC: Look up EC in DSDT [ 37.010681] ACPI: Interpreter enabled [ 37.010719] ACPI: (supports S0 S1 S3 S4 S5) [ 37.010888] ACPI: Using IOAPIC for interrupt routing [ 37.011098] Error attaching device data [ 37.011137] Error attaching device data [ 37.011176] Error attaching device data [ 37.011214] Error attaching device data [ 37.016127] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 37.016652] PCI: Transparent bridge - 0000:00:08.0 [ 37.016946] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 37.017078] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] [ 37.017175] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR10._PRT] [ 37.017230] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR11._PRT] [ 37.017285] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR13._PRT] [ 37.017340] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR12._PRT] [ 37.021278] ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *11 [ 37.021614] ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *5 [ 37.021948] ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *0, disabled. [ 37.022309] ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *0, disabled. [ 37.022668] ACPI: PCI Interrupt Link [LNEA] (IRQs 16 17 18 19) *0, disabled. [ 37.023028] ACPI: PCI Interrupt Link [LNEB] (IRQs 16 17 18 19) *10 [ 37.023362] ACPI: PCI Interrupt Link [LNEC] (IRQs 16 17 18 19) *0, disabled. [ 37.023721] ACPI: PCI Interrupt Link [LNED] (IRQs 16 17 18 19) *10 [ 37.024058] ACPI: PCI Interrupt Link [LUB0] (IRQs 20 21 22 23) *5 [ 37.024392] ACPI: PCI Interrupt Link [LMAD] (IRQs 20 21 22 23) *0, disabled. [ 37.024752] ACPI: PCI Interrupt Link [LUB2] (IRQs 20 21 22 23) *7 [ 37.025087] ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *0, disabled. [ 37.025447] ACPI: PCI Interrupt Link [LAZA] (IRQs 20 21 22 23) *0, disabled. [ 37.025807] ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *11 [ 37.026141] ACPI: PCI Interrupt Link [LPMU] (IRQs 20 21 22 23) *0, disabled. [ 37.026502] ACPI: PCI Interrupt Link [LSA0] (IRQs 20 21 22 23) *15 [ 37.026836] ACPI: PCI Interrupt Link [LSA1] (IRQs 20 21 22 23) *0, disabled. [ 37.027233] ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22 23) *0, disabled. [ 37.027594] ACPI: PCI Interrupt Link [UB11] (IRQs 20 21 22 23) *0, disabled. [ 37.027955] ACPI: PCI Interrupt Link [UB12] (IRQs 20 21 22 23) *0, disabled. [ 37.028273] Linux Plug and Play Support v0.97 (c) Adam Belay [ 37.028326] pnp: PnP ACPI init [ 37.028365] ACPI: bus type pnp registered [ 37.030905] pnp: PnP ACPI: found 13 devices [ 37.030943] ACPI: ACPI bus type pnp unregistered [ 37.031065] SCSI subsystem initialized [ 37.031122] libata version 3.00 loaded. [ 37.031172] usbcore: registered new interface driver usbfs [ 37.031227] usbcore: registered new interface driver hub [ 37.031284] usbcore: registered new device driver usb [ 37.031367] PCI: Using ACPI for IRQ routing [ 37.031405] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 37.040479] PCI-DMA: Disabling AGP. [ 37.041215] PCI-DMA: aperture base @ 8000000 size 65536 KB [ 37.041257] PCI-DMA: using GART IOMMU. [ 37.041296] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture [ 37.041455] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31 [ 37.041595] hpet0: 3 32-bit timers, 25000000 Hz [ 37.043764] Time: hpet clocksource has been installed. [ 37.043812] Switched to high resolution mode on CPU 0 [ 37.043970] Switched to high resolution mode on CPU 1 [ 37.050495] system 00:05: ioport range 0x4d0-0x4d1 has been reserved [ 37.050535] system 00:05: ioport range 0x800-0x80f has been reserved [ 37.050575] system 00:05: ioport range 0x2000-0x207f has been reserved [ 37.050614] system 00:05: ioport range 0x2080-0x20ff has been reserved [ 37.054014] system 00:05: ioport range 0x2400-0x247f has been reserved [ 37.054053] system 00:05: ioport range 0x2480-0x24ff has been reserved [ 37.054092] system 00:05: ioport range 0x2800-0x287f has been reserved [ 37.054131] system 00:05: ioport range 0x2880-0x28ff has been reserved [ 37.054171] system 00:05: ioport range 0x2c00-0x2c7f has been reserved [ 37.054210] system 00:05: ioport range 0x2c80-0x2cff has been reserved [ 37.054250] system 00:05: iomem range 0x0-0x0 could not be reserved [ 37.054290] system 00:05: iomem range 0xfee01000-0xfeefffff has been reserved [ 37.054333] system 00:07: iomem range 0xfec00000-0xfec00fff could not be reserved [ 37.054381] system 00:07: iomem range 0xfee00000-0xfee00fff could not be reserved [ 37.054432] system 00:0a: ioport range 0x290-0x29f has been reserved [ 37.054474] system 00:0b: iomem range 0xe0000000-0xefffffff has been reserved [ 37.054519] system 00:0c: iomem range 0x0-0x9ffff could not be reserved [ 37.054558] system 00:0c: iomem range 0xc0000-0xcffff has been reserved [ 37.054601] system 00:0c: iomem range 0xe0000-0xfffff could not be reserved [ 37.054641] system 00:0c: iomem range 0x100000-0xcfffffff could not be reserved [ 37.054688] system 00:0c: iomem range 0xff380000-0xffffffff could not be reserved [ 37.054970] PCI: Bridge: 0000:00:08.0 [ 37.055007] IO window: d000-dfff [ 37.055044] MEM window: f9f00000-f9ffffff [ 37.055081] PREFETCH window: disabled. [ 37.055119] PCI: Bridge: 0000:00:0b.0 [ 37.055155] IO window: c000-cfff [ 37.055192] MEM window: f9e00000-f9efffff [ 37.055229] PREFETCH window: disabled. [ 37.055266] PCI: Bridge: 0000:00:0c.0 [ 37.055302] IO window: disabled. [ 37.055338] MEM window: disabled. [ 37.055374] PREFETCH window: disabled. [ 37.055411] PCI: Bridge: 0000:00:0d.0 [ 37.055448] IO window: e000-efff [ 37.055484] MEM window: fa000000-febfffff [ 37.055521] PREFETCH window: d0000000-dfffffff [ 37.055559] PCI: Bridge: 0000:00:0e.0 [ 37.055595] IO window: disabled. [ 37.055631] MEM window: disabled. [ 37.055668] PREFETCH window: disabled. [ 37.055711] PCI: Setting latency timer of device 0000:00:08.0 to 64 [ 37.055719] PCI: Setting latency timer of device 0000:00:0b.0 to 64 [ 37.055724] PCI: Setting latency timer of device 0000:00:0c.0 to 64 [ 37.055729] PCI: Setting latency timer of device 0000:00:0d.0 to 64 [ 37.055733] PCI: Setting latency timer of device 0000:00:0e.0 to 64 [ 37.055739] NET: Registered protocol family 2 [ 37.087062] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 37.087659] TCP established hash table entries: 262144 (order: 10, 4194304 bytes) [ 37.089081] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 37.089567] TCP: Hash tables configured (established 262144 bind 65536) [ 37.089607] TCP reno registered [ 37.097846] Loading Reiser4. See www.namesys.com for a description of Reiser4. [ 37.097949] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) [ 37.097997] io scheduler noop registered [ 37.098035] io scheduler cfq registered (default) [ 37.098731] Boot video device is 0000:04:00.0 [ 37.098833] PCI: Setting latency timer of device 0000:00:0b.0 to 64 [ 37.098850] assign_interrupt_mode Found MSI capability [ 37.098904] Allocate Port Service[0000:00:0b.0:pcie00] [ 37.098946] PCI: Setting latency timer of device 0000:00:0c.0 to 64 [ 37.098962] assign_interrupt_mode Found MSI capability [ 37.099010] Allocate Port Service[0000:00:0c.0:pcie00] [ 37.099047] PCI: Setting latency timer of device 0000:00:0d.0 to 64 [ 37.099063] assign_interrupt_mode Found MSI capability [ 37.099111] Allocate Port Service[0000:00:0d.0:pcie00] [ 37.099148] PCI: Setting latency timer of device 0000:00:0e.0 to 64 [ 37.099164] assign_interrupt_mode Found MSI capability [ 37.099212] Allocate Port Service[0000:00:0e.0:pcie00] [ 37.099387] input: Power Button (FF) as /class/input/input0 [ 37.099425] ACPI: Power Button (FF) [PWRF] [ 37.099510] input: Power Button (CM) as /class/input/input1 [ 37.099549] ACPI: Power Button (CM) [PWRB] [ 37.099683] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126] [ 37.099788] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126] [ 37.123685] Real Time Clock Driver v1.12ac [ 37.123804] hpet_resources: 0xfed00000 is busy [ 37.123821] Linux agpgart interface v0.102 [ 37.123907] Driver 'sd' needs updating - please use bus_type methods [ 37.123980] ahci 0000:00:0a.0: version 3.0 [ 37.124155] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 23 [ 37.124199] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LSA0] -> GSI 23 (level, low) -> IRQ 23 [ 37.124533] ahci 0000:00:0a.0: controller can't do PMP, turning off CAP_PMP [ 38.124731] ahci 0000:00:0a.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl IDE mode [ 38.124780] ahci 0000:00:0a.0: flags: 64bit sntf led clo pio [ 38.124819] PCI: Setting latency timer of device 0000:00:0a.0 to 64 [ 38.125020] scsi0 : ahci [ 38.125116] scsi1 : ahci [ 38.125182] scsi2 : ahci [ 38.125248] scsi3 : ahci [ 38.125337] ata1: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc100 irq 315 [ 38.125384] ata2: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc180 irq 315 [ 38.125432] ata3: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc200 irq 315 [ 38.125479] ata4: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc280 irq 315 [ 38.597035] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 38.597732] ata1.00: ATA-7: WDC WD1600JS-00MHB1, 10.02E01, max UDMA/133 [ 38.597775] ata1.00: 312581808 sectors, multi 16: LBA48 [ 38.598405] ata1.00: configured for UDMA/133 [ 39.069342] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 39.084225] ata2.00: ATA-8: SAMSUNG HD501LJ, CR100-12, max UDMA7 [ 39.084264] ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32) [ 39.086268] ata2.00: configured for UDMA/133 [ 39.405277] ata3: SATA link down (SStatus 0 SControl 300) [ 39.724583] ata4: SATA link down (SStatus 0 SControl 300) [ 39.724672] scsi 0:0:0:0: Direct-Access ATA WDC WD1600JS-00M 10.0 PQ: 0 ANSI: 5 [ 39.724782] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB) [ 39.724826] sd 0:0:0:0: [sda] Write Protect is off [ 39.724864] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 39.724872] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 39.724942] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB) [ 39.724985] sd 0:0:0:0: [sda] Write Protect is off [ 39.725023] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 39.725030] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 39.725079] sda: sda1 sda2 sda3 sda4 < sda5 sda6 > [ 39.763787] sd 0:0:0:0: [sda] Attached SCSI disk [ 39.763923] scsi 1:0:0:0: Direct-Access ATA SAMSUNG HD501LJ CR10 PQ: 0 ANSI: 5 [ 39.764032] sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) [ 39.764077] sd 1:0:0:0: [sdb] Write Protect is off [ 39.764115] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 39.764124] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 39.764194] sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) [ 39.764237] sd 1:0:0:0: [sdb] Write Protect is off [ 39.764275] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 39.764283] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 39.764332] sdb: sdb1 sdb2 [ 39.793043] sd 1:0:0:0: [sdb] Attached SCSI disk [ 39.793181] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12 [ 39.795761] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 39.795800] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 39.822033] usbcore: registered new interface driver usbhid [ 39.822072] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver [ 39.822116] TCP cubic registered [ 39.822155] NET: Registered protocol family 1 [ 39.822210] powernow-k8: Found 1 AMD Athlon(tm) 64 X2 Dual Core Processor 6000+ processors (2 cpu cores) (version 2.20.00) [ 39.822187] powernow-k8: 0 : fid 0x16 (3000 MHz), vid 0x6 [ 39.822226] powernow-k8: 1 : fid 0x14 (2800 MHz), vid 0x8 [ 39.822265] powernow-k8: 2 : fid 0x12 (2600 MHz), vid 0xa [ 39.822303] powernow-k8: 3 : fid 0x10 (2400 MHz), vid 0xc [ 39.822341] powernow-k8: 4 : fid 0xe (2200 MHz), vid 0xe [ 39.822379] powernow-k8: 5 : fid 0xc (2000 MHz), vid 0x10 [ 39.822417] powernow-k8: 6 : fid 0xa (1800 MHz), vid 0x10 [ 39.822456] powernow-k8: 7 : fid 0x2 (1000 MHz), vid 0x12 [ 39.848293] input: AT Translated Set 2 keyboard as /class/input/input2 [ 39.942989] ReiserFS: sda3: found reiserfs format "3.6" with standard journal [ 39.943032] ReiserFS: sda3: using ordered data mode [ 39.952565] ReiserFS: sda3: journal params: device sda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 [ 39.953453] ReiserFS: sda3: checking transaction log (sda3) [ 39.996872] ReiserFS: sda3: Using r5 hash to sort names [ 39.996923] VFS: Mounted root (reiserfs filesystem) readonly. [ 39.996972] Freeing unused kernel memory: 176k freed [ 40.878988] Clocksource tsc unstable (delta = -333079246 ns) [ 42.095345] ReiserFS: sda3: switching to journaled data mode [ 42.226791] r8169 Gigabit Ethernet driver 2.2LK loaded [ 42.226996] ACPI: PCI Interrupt Link [LNEB] enabled at IRQ 19 [ 42.227002] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNEB] -> GSI 19 (level, low) -> IRQ 19 [ 42.227010] PCI: Setting latency timer of device 0000:01:00.0 to 64 [ 42.227158] eth0: RTL8168b/8111b at 0xffffc20000170000, 00:19:66:47:f3:cb, XID 38000000 IRQ 314 [ 42.239735] ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 22 [ 42.239745] ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUB2] -> GSI 22 (level, low) -> IRQ 22 [ 42.239894] PCI: Setting latency timer of device 0000:00:02.1 to 64 [ 42.239897] ehci_hcd 0000:00:02.1: EHCI Host Controller [ 42.239970] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1 [ 42.239992] ehci_hcd 0000:00:02.1: debug port 1 [ 42.239994] PCI: cache line size of 64 is not supported by device 0000:00:02.1 [ 42.240001] ehci_hcd 0000:00:02.1: irq 22, io mem 0xf9dfec00 [ 42.243080] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 42.243150] usb usb1: configuration #1 chosen from 1 choice [ 42.243165] hub 1-0:1.0: USB hub found [ 42.243170] hub 1-0:1.0: 10 ports detected [ 42.352456] usb 1-3: new high speed USB device using ehci_hcd and address 2 [ 42.394298] usb 1-3: configuration #1 chosen from 1 choice [ 42.394382] hub 1-3:1.0: USB hub found [ 42.394494] hub 1-3:1.0: 4 ports detected [ 42.398785] reiser4: sdb2: found disk format 4.0.0. [ 42.493443] usb 1-3.1: new low speed USB device using ehci_hcd and address 3 [ 42.527871] usb 1-3.1: configuration #1 chosen from 1 choice [ 42.531596] input: Logitech USB Receiver as /class/input/input3 [ 42.536888] input: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:02.1-3.1 [ 42.539011] input: Logitech USB Receiver as /class/input/input4 [ 42.552418] input: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:02.1-3.1 [ 42.561737] mice: PS/2 mouse device common for all mice [ 50.915448] reiser4: sda6: found disk format 4.0.0. [ 51.353992] reiser4: sdb1: found disk format 4.0.0. [ 51.733762] Adding 1951888k swap on /dev/sda2. Priority:-1 extents:1 across:1951888k [ 53.133822] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 18 [ 53.133828] ACPI: PCI Interrupt 0000:02:09.0[A] -> Link [LNKB] -> GSI 18 (level, low) -> IRQ 18 [ 53.134923] Audigy2 value: Special config. [ 54.973693] w83627ehf: Found W83627EHG chip at 0x290 [ 55.827810] r8169: eth0: link up [ 55.827816] r8169: eth0: link up [ 56.557555] NET: Registered protocol family 17
[ 0.000000] Linux version 2.6.24.3reiser4ahci_no_srst (root@energy) (gcc version 4.2.3 (Gentoo 4.2.3 p1.0)) #1 SMP Wed Mar 19 07:57:35 CET 2008 [ 0.000000] Command line: root=/dev/sda3 nmi_watchdog=0 console=tty6 [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000e6000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 00000000cffb0000 (usable) [ 0.000000] BIOS-e820: 00000000cffb0000 - 00000000cffc0000 (ACPI data) [ 0.000000] BIOS-e820: 00000000cffc0000 - 00000000cfff0000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000cfff0000 - 00000000d0000000 (reserved) [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved) [ 0.000000] BIOS-e820: 00000000ff380000 - 0000000100000000 (reserved) [ 0.000000] BIOS-e820: 0000000100000000 - 0000000130000000 (usable) [ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 256 used [ 0.000000] Entering add_active_range(0, 256, 851888) 1 entries of 256 used [ 0.000000] Entering add_active_range(0, 1048576, 1245184) 2 entries of 256 used [ 0.000000] end_pfn_map = 1245184 [ 0.000000] DMI present. [ 0.000000] ACPI: RSDP 000F98E0, 0014 (r0 ACPIAM) [ 0.000000] ACPI: RSDT CFFB0000, 003C (r1 A M I OEMRSDT 12000731 MSFT 97) [ 0.000000] ACPI: FACP CFFB0200, 0084 (r2 A_M_I OEMFACP 12000601 MSFT 97) [ 0.000000] ACPI: DSDT CFFB0450, 4FFA (r1 ASR19 ASR19186 186 INTL 20051117) [ 0.000000] ACPI: FACS CFFC0000, 0040 [ 0.000000] ACPI: APIC CFFB0390, 0080 (r1 A M I OEMAPIC 12000731 MSFT 97) [ 0.000000] ACPI: MCFG CFFB0410, 003C (r1 A M I OEMMCFG 12000731 MSFT 97) [ 0.000000] ACPI: OEMB CFFC0040, 0060 (r1 A M I AMI_OEM 12000731 MSFT 97) [ 0.000000] ACPI: HPET CFFB5450, 0038 (r1 A M I OEMHPET0 12000731 MSFT 97) [ 0.000000] ACPI: SSDT CFFB5490, 030E (r1 A M I POWERNOW 1 AMD 1) [ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 256 used [ 0.000000] Entering add_active_range(0, 256, 851888) 1 entries of 256 used [ 0.000000] Entering add_active_range(0, 1048576, 1245184) 2 entries of 256 used [ 0.000000] No mptable found. [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] DMA32 4096 -> 1048576 [ 0.000000] Normal 1048576 -> 1245184 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[3] active PFN ranges [ 0.000000] 0: 0 -> 159 [ 0.000000] 0: 256 -> 851888 [ 0.000000] 0: 1048576 -> 1245184 [ 0.000000] On node 0 totalpages: 1048399 [ 0.000000] DMA zone: 56 pages used for memmap [ 0.000000] DMA zone: 853 pages reserved [ 0.000000] DMA zone: 3090 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 14280 pages used for memmap [ 0.000000] DMA32 zone: 833512 pages, LIFO batch:31 [ 0.000000] Normal zone: 2688 pages used for memmap [ 0.000000] Normal zone: 193920 pages, LIFO batch:31 [ 0.000000] Movable zone: 0 pages used for memmap [ 0.000000] ACPI: PM-Timer IO Port: 0x2008 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) [ 0.000000] Processor #0 (Bootup-CPU) [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) [ 0.000000] Processor #1 [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled) [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] ACPI: IRQ14 used by override. [ 0.000000] ACPI: IRQ15 used by override. [ 0.000000] Setting APIC routing to flat [ 0.000000] ACPI: HPET id: 0x10de8201 base: 0xfed00000 [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000 [ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e6000 [ 0.000000] swsusp: Registered nosave memory region: 00000000000e6000 - 0000000000100000 [ 0.000000] swsusp: Registered nosave memory region: 00000000cffb0000 - 00000000cffc0000 [ 0.000000] swsusp: Registered nosave memory region: 00000000cffc0000 - 00000000cfff0000 [ 0.000000] swsusp: Registered nosave memory region: 00000000cfff0000 - 00000000d0000000 [ 0.000000] swsusp: Registered nosave memory region: 00000000d0000000 - 00000000fec00000 [ 0.000000] swsusp: Registered nosave memory region: 00000000fec00000 - 00000000fec01000 [ 0.000000] swsusp: Registered nosave memory region: 00000000fec01000 - 00000000fee00000 [ 0.000000] swsusp: Registered nosave memory region: 00000000fee00000 - 00000000fef00000 [ 0.000000] swsusp: Registered nosave memory region: 00000000fef00000 - 00000000ff380000 [ 0.000000] swsusp: Registered nosave memory region: 00000000ff380000 - 0000000100000000 [ 0.000000] Allocating PCI resources starting at d4000000 (gap: d0000000:2ec00000) [ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs [ 0.000000] PERCPU: Allocating 31408 bytes of per cpu data [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1030522 [ 0.000000] Kernel command line: root=/dev/sda3 nmi_watchdog=0 console=tty6 [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes) [ 0.000000] hpet clockevent registered [ 0.000000] TSC calibrated against HPET [ 39.090700] Marking TSC unstable due to TSCs unsynchronized [ 39.090702] time.c: Detected 3013.888 MHz processor. [ 39.094534] Console: colour VGA+ 80x25 [ 39.094536] console [tty6] enabled [ 39.099146] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 39.101376] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 39.102148] Checking aperture... [ 39.102186] CPU 0: aperture @ 8000000 size 32 MB [ 39.102223] Aperture too small (32 MB) [ 39.108105] No AGP bridge found [ 39.108140] Your BIOS doesn't leave a aperture memory hole [ 39.108178] Please enable the IOMMU option in the BIOS setup [ 39.108216] This costs you 64 MB of RAM [ 39.133445] Mapping aperture over 65536 KB of RAM @ 8000000 [ 39.157576] Memory: 4049948k/4980736k available (2192k kernel code, 143428k reserved, 681k data, 176k init) [ 39.157645] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1 [ 39.240351] Calibrating delay using timer specific routine.. 6034.68 BogoMIPS (lpj=10053897) [ 39.240444] Mount-cache hash table entries: 256 [ 39.240551] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 39.240591] CPU: L2 Cache: 1024K (64 bytes/line) [ 39.240629] CPU: Physical Processor ID: 0 [ 39.240665] CPU: Processor Core ID: 0 [ 39.240718] SMP alternatives: switching to UP code [ 39.241081] ACPI: Core revision 20070126 [ 39.276257] Using local APIC timer interrupts. [ 39.309401] APIC timer calibration result 12557874 [ 39.309402] Detected 12.557 MHz APIC timer. [ 39.309488] SMP alternatives: switching to SMP code [ 39.309718] Booting processor 1/2 APIC 0x1 [ 39.319858] Initializing CPU#1 [ 39.402621] Calibrating delay using timer specific routine.. 6030.92 BogoMIPS (lpj=10046282) [ 39.402626] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 39.402627] CPU: L2 Cache: 1024K (64 bytes/line) [ 39.402629] CPU: Physical Processor ID: 0 [ 39.402630] CPU: Processor Core ID: 1 [ 39.402711] AMD Athlon(tm) 64 X2 Dual Core Processor 6000+ stepping 03 [ 39.402745] Brought up 2 CPUs [ 39.403204] net_namespace: 120 bytes [ 39.403436] NET: Registered protocol family 16 [ 39.403548] ACPI: bus type pci registered [ 39.403630] PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved [ 39.403669] PCI: Not using MMCONFIG. [ 39.403705] PCI: Using configuration type 1 [ 39.405948] ACPI: EC: Look up EC in DSDT [ 39.409394] ACPI: Interpreter enabled [ 39.409432] ACPI: (supports S0 S1 S3 S4 S5) [ 39.409602] ACPI: Using IOAPIC for interrupt routing [ 39.409811] Error attaching device data [ 39.409850] Error attaching device data [ 39.409889] Error attaching device data [ 39.409928] Error attaching device data [ 39.414841] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 39.415367] PCI: Transparent bridge - 0000:00:08.0 [ 39.415661] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 39.415792] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] [ 39.415889] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR10._PRT] [ 39.415944] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR11._PRT] [ 39.415999] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR13._PRT] [ 39.416055] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR12._PRT] [ 39.419993] ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *11 [ 39.420329] ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *5 [ 39.420664] ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *0, disabled. [ 39.421026] ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *0, disabled. [ 39.421386] ACPI: PCI Interrupt Link [LNEA] (IRQs 16 17 18 19) *0, disabled. [ 39.421746] ACPI: PCI Interrupt Link [LNEB] (IRQs 16 17 18 19) *10 [ 39.422081] ACPI: PCI Interrupt Link [LNEC] (IRQs 16 17 18 19) *0, disabled. [ 39.422441] ACPI: PCI Interrupt Link [LNED] (IRQs 16 17 18 19) *10 [ 39.422778] ACPI: PCI Interrupt Link [LUB0] (IRQs 20 21 22 23) *5 [ 39.423113] ACPI: PCI Interrupt Link [LMAD] (IRQs 20 21 22 23) *0, disabled. [ 39.423474] ACPI: PCI Interrupt Link [LUB2] (IRQs 20 21 22 23) *7 [ 39.423808] ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *0, disabled. [ 39.424169] ACPI: PCI Interrupt Link [LAZA] (IRQs 20 21 22 23) *0, disabled. [ 39.424529] ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *11 [ 39.424864] ACPI: PCI Interrupt Link [LPMU] (IRQs 20 21 22 23) *0, disabled. [ 39.425225] ACPI: PCI Interrupt Link [LSA0] (IRQs 20 21 22 23) *15 [ 39.425560] ACPI: PCI Interrupt Link [LSA1] (IRQs 20 21 22 23) *0, disabled. [ 39.425958] ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22 23) *0, disabled. [ 39.426318] ACPI: PCI Interrupt Link [UB11] (IRQs 20 21 22 23) *0, disabled. [ 39.426679] ACPI: PCI Interrupt Link [UB12] (IRQs 20 21 22 23) *0, disabled. [ 39.426998] Linux Plug and Play Support v0.97 (c) Adam Belay [ 39.427051] pnp: PnP ACPI init [ 39.427090] ACPI: bus type pnp registered [ 39.429629] pnp: PnP ACPI: found 13 devices [ 39.429666] ACPI: ACPI bus type pnp unregistered [ 39.429789] SCSI subsystem initialized [ 39.429845] libata version 3.00 loaded. [ 39.429896] usbcore: registered new interface driver usbfs [ 39.429952] usbcore: registered new interface driver hub [ 39.430009] usbcore: registered new device driver usb [ 39.430092] PCI: Using ACPI for IRQ routing [ 39.430130] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 39.439195] PCI-DMA: Disabling AGP. [ 39.439931] PCI-DMA: aperture base @ 8000000 size 65536 KB [ 39.439973] PCI-DMA: using GART IOMMU. [ 39.440013] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture [ 39.440171] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31 [ 39.440311] hpet0: 3 32-bit timers, 25000000 Hz [ 39.442480] Time: hpet clocksource has been installed. [ 39.442528] Switched to high resolution mode on CPU 0 [ 39.442640] Switched to high resolution mode on CPU 1 [ 39.449212] system 00:05: ioport range 0x4d0-0x4d1 has been reserved [ 39.449252] system 00:05: ioport range 0x800-0x80f has been reserved [ 39.449291] system 00:05: ioport range 0x2000-0x207f has been reserved [ 39.449331] system 00:05: ioport range 0x2080-0x20ff has been reserved [ 39.452732] system 00:05: ioport range 0x2400-0x247f has been reserved [ 39.452772] system 00:05: ioport range 0x2480-0x24ff has been reserved [ 39.452811] system 00:05: ioport range 0x2800-0x287f has been reserved [ 39.452850] system 00:05: ioport range 0x2880-0x28ff has been reserved [ 39.452890] system 00:05: ioport range 0x2c00-0x2c7f has been reserved [ 39.452929] system 00:05: ioport range 0x2c80-0x2cff has been reserved [ 39.452969] system 00:05: iomem range 0x0-0x0 could not be reserved [ 39.453009] system 00:05: iomem range 0xfee01000-0xfeefffff has been reserved [ 39.453053] system 00:07: iomem range 0xfec00000-0xfec00fff could not be reserved [ 39.453100] system 00:07: iomem range 0xfee00000-0xfee00fff could not be reserved [ 39.453151] system 00:0a: ioport range 0x290-0x29f has been reserved [ 39.453193] system 00:0b: iomem range 0xe0000000-0xefffffff has been reserved [ 39.453238] system 00:0c: iomem range 0x0-0x9ffff could not be reserved [ 39.453278] system 00:0c: iomem range 0xc0000-0xcffff has been reserved [ 39.453321] system 00:0c: iomem range 0xe0000-0xfffff could not be reserved [ 39.453361] system 00:0c: iomem range 0x100000-0xcfffffff could not be reserved [ 39.453408] system 00:0c: iomem range 0xff380000-0xffffffff could not be reserved [ 39.453690] PCI: Bridge: 0000:00:08.0 [ 39.453728] IO window: d000-dfff [ 39.453765] MEM window: f9f00000-f9ffffff [ 39.453802] PREFETCH window: disabled. [ 39.453840] PCI: Bridge: 0000:00:0b.0 [ 39.453876] IO window: c000-cfff [ 39.453913] MEM window: f9e00000-f9efffff [ 39.453950] PREFETCH window: disabled. [ 39.453987] PCI: Bridge: 0000:00:0c.0 [ 39.454023] IO window: disabled. [ 39.454060] MEM window: disabled. [ 39.454096] PREFETCH window: disabled. [ 39.454133] PCI: Bridge: 0000:00:0d.0 [ 39.454170] IO window: e000-efff [ 39.454206] MEM window: fa000000-febfffff [ 39.454243] PREFETCH window: d0000000-dfffffff [ 39.454281] PCI: Bridge: 0000:00:0e.0 [ 39.454317] IO window: disabled. [ 39.454354] MEM window: disabled. [ 39.454390] PREFETCH window: disabled. [ 39.454433] PCI: Setting latency timer of device 0000:00:08.0 to 64 [ 39.454441] PCI: Setting latency timer of device 0000:00:0b.0 to 64 [ 39.454446] PCI: Setting latency timer of device 0000:00:0c.0 to 64 [ 39.454451] PCI: Setting latency timer of device 0000:00:0d.0 to 64 [ 39.454456] PCI: Setting latency timer of device 0000:00:0e.0 to 64 [ 39.454462] NET: Registered protocol family 2 [ 39.485778] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 39.486375] TCP established hash table entries: 262144 (order: 10, 4194304 bytes) [ 39.487800] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 39.488284] TCP: Hash tables configured (established 262144 bind 65536) [ 39.488324] TCP reno registered [ 39.496560] Loading Reiser4. See www.namesys.com for a description of Reiser4. [ 39.496664] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) [ 39.496712] io scheduler noop registered [ 39.496750] io scheduler cfq registered (default) [ 39.497446] Boot video device is 0000:04:00.0 [ 39.497548] PCI: Setting latency timer of device 0000:00:0b.0 to 64 [ 39.497565] assign_interrupt_mode Found MSI capability [ 39.497619] Allocate Port Service[0000:00:0b.0:pcie00] [ 39.497661] PCI: Setting latency timer of device 0000:00:0c.0 to 64 [ 39.497677] assign_interrupt_mode Found MSI capability [ 39.497725] Allocate Port Service[0000:00:0c.0:pcie00] [ 39.497762] PCI: Setting latency timer of device 0000:00:0d.0 to 64 [ 39.497778] assign_interrupt_mode Found MSI capability [ 39.497826] Allocate Port Service[0000:00:0d.0:pcie00] [ 39.497864] PCI: Setting latency timer of device 0000:00:0e.0 to 64 [ 39.497880] assign_interrupt_mode Found MSI capability [ 39.497928] Allocate Port Service[0000:00:0e.0:pcie00] [ 39.498102] input: Power Button (FF) as /class/input/input0 [ 39.498141] ACPI: Power Button (FF) [PWRF] [ 39.498226] input: Power Button (CM) as /class/input/input1 [ 39.498264] ACPI: Power Button (CM) [PWRB] [ 39.498398] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126] [ 39.498503] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126] [ 39.522401] Real Time Clock Driver v1.12ac [ 39.522520] hpet_resources: 0xfed00000 is busy [ 39.522537] Linux agpgart interface v0.102 [ 39.522623] Driver 'sd' needs updating - please use bus_type methods [ 39.522696] ahci 0000:00:0a.0: version 3.0 [ 39.522871] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 23 [ 39.522914] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LSA0] -> GSI 23 (level, low) -> IRQ 23 [ 39.523247] ahci 0000:00:0a.0: controller can't do PMP, turning off CAP_PMP [ 40.523447] ahci 0000:00:0a.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl IDE mode [ 40.523496] ahci 0000:00:0a.0: flags: 64bit sntf led clo pio [ 40.523535] PCI: Setting latency timer of device 0000:00:0a.0 to 64 [ 40.523737] scsi0 : ahci [ 40.523832] scsi1 : ahci [ 40.523898] scsi2 : ahci [ 40.523964] scsi3 : ahci [ 40.524053] ata1: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc100 irq 315 [ 40.524100] ata2: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc180 irq 315 [ 40.524148] ata3: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc200 irq 315 [ 40.524195] ata4: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc280 irq 315 [ 40.995751] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 40.996374] ata1.00: ATA-7: WDC WD1600JS-00MHB1, 10.02E01, max UDMA/133 [ 40.996416] ata1.00: 312581808 sectors, multi 16: LBA48 [ 40.997049] ata1.00: configured for UDMA/133 [ 41.468058] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 41.471873] ata2.00: ATA-8: SAMSUNG HD501LJ, CR100-12, max UDMA7 [ 41.471913] ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32) [ 41.473917] ata2.00: configured for UDMA/133 [ 41.790689] ata3: SATA link down (SStatus 0 SControl 300) [ 42.109995] ata4: SATA link down (SStatus 0 SControl 300) [ 42.110084] scsi 0:0:0:0: Direct-Access ATA WDC WD1600JS-00M 10.0 PQ: 0 ANSI: 5 [ 42.110194] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB) [ 42.110238] sd 0:0:0:0: [sda] Write Protect is off [ 42.110276] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 42.110284] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 42.110354] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB) [ 42.110397] sd 0:0:0:0: [sda] Write Protect is off [ 42.110435] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 42.110442] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 42.110492] sda: sda1 sda2 sda3 sda4 < sda5 sda6 > [ 42.140153] sd 0:0:0:0: [sda] Attached SCSI disk [ 42.140289] scsi 1:0:0:0: Direct-Access ATA SAMSUNG HD501LJ CR10 PQ: 0 ANSI: 5 [ 42.140398] sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) [ 42.140443] sd 1:0:0:0: [sdb] Write Protect is off [ 42.140481] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 42.140489] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 42.140559] sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) [ 42.140602] sd 1:0:0:0: [sdb] Write Protect is off [ 42.140639] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 42.140647] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 42.140696] sdb: sdb1 sdb2 [ 42.167607] sd 1:0:0:0: [sdb] Attached SCSI disk [ 42.167745] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12 [ 42.170531] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 42.170571] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 42.197421] usbcore: registered new interface driver usbhid [ 42.197459] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver [ 42.197504] TCP cubic registered [ 42.197543] NET: Registered protocol family 1 [ 42.197597] powernow-k8: Found 1 AMD Athlon(tm) 64 X2 Dual Core Processor 6000+ processors (2 cpu cores) (version 2.20.00) [ 42.197621] powernow-k8: 0 : fid 0x16 (3000 MHz), vid 0x6 [ 42.197660] powernow-k8: 1 : fid 0x14 (2800 MHz), vid 0x8 [ 42.197699] powernow-k8: 2 : fid 0x12 (2600 MHz), vid 0xa [ 42.197737] powernow-k8: 3 : fid 0x10 (2400 MHz), vid 0xc [ 42.197775] powernow-k8: 4 : fid 0xe (2200 MHz), vid 0xe [ 42.197813] powernow-k8: 5 : fid 0xc (2000 MHz), vid 0x10 [ 42.197851] powernow-k8: 6 : fid 0xa (1800 MHz), vid 0x10 [ 42.197890] powernow-k8: 7 : fid 0x2 (1000 MHz), vid 0x12 [ 42.224668] input: AT Translated Set 2 keyboard as /class/input/input2 [ 42.319352] ReiserFS: sda3: found reiserfs format "3.6" with standard journal [ 42.319395] ReiserFS: sda3: using ordered data mode [ 42.328929] ReiserFS: sda3: journal params: device sda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 [ 42.329817] ReiserFS: sda3: checking transaction log (sda3) [ 42.373235] ReiserFS: sda3: Using r5 hash to sort names [ 42.373286] VFS: Mounted root (reiserfs filesystem) readonly. [ 42.373335] Freeing unused kernel memory: 176k freed [ 43.277704] Clocksource tsc unstable (delta = -333079178 ns) [ 44.475534] ReiserFS: sda3: switching to journaled data mode [ 44.609715] r8169 Gigabit Ethernet driver 2.2LK loaded [ 44.609920] ACPI: PCI Interrupt Link [LNEB] enabled at IRQ 19 [ 44.609925] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNEB] -> GSI 19 (level, low) -> IRQ 19 [ 44.609934] PCI: Setting latency timer of device 0000:01:00.0 to 64 [ 44.610080] eth0: RTL8168b/8111b at 0xffffc20000170000, 00:19:66:47:f3:cb, XID 38000000 IRQ 314 [ 44.628294] ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 22 [ 44.628300] ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUB2] -> GSI 22 (level, low) -> IRQ 22 [ 44.628468] PCI: Setting latency timer of device 0000:00:02.1 to 64 [ 44.628472] ehci_hcd 0000:00:02.1: EHCI Host Controller [ 44.628547] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1 [ 44.628568] ehci_hcd 0000:00:02.1: debug port 1 [ 44.628571] PCI: cache line size of 64 is not supported by device 0000:00:02.1 [ 44.628576] ehci_hcd 0000:00:02.1: irq 22, io mem 0xf9dfec00 [ 44.637353] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 44.637437] usb usb1: configuration #1 chosen from 1 choice [ 44.637453] hub 1-0:1.0: USB hub found [ 44.637459] hub 1-0:1.0: 10 ports detected [ 44.746738] usb 1-3: new high speed USB device using ehci_hcd and address 2 [ 44.788570] usb 1-3: configuration #1 chosen from 1 choice [ 44.788654] hub 1-3:1.0: USB hub found [ 44.788766] hub 1-3:1.0: 4 ports detected [ 44.792882] reiser4: sdb2: found disk format 4.0.0. [ 44.887964] usb 1-3.1: new low speed USB device using ehci_hcd and address 3 [ 44.922094] usb 1-3.1: configuration #1 chosen from 1 choice [ 44.925824] input: Logitech USB Receiver as /class/input/input3 [ 44.932248] input: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:02.1-3.1 [ 44.934322] input: Logitech USB Receiver as /class/input/input4 [ 44.949978] input: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:02.1-3.1 [ 44.958863] mice: PS/2 mouse device common for all mice [ 53.303908] reiser4: sda6: found disk format 4.0.0. [ 53.750119] reiser4: sdb1: found disk format 4.0.0. [ 54.136067] Adding 1951888k swap on /dev/sda2. Priority:-1 extents:1 across:1951888k [ 55.658007] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 18 [ 55.658013] ACPI: PCI Interrupt 0000:02:09.0[A] -> Link [LNKB] -> GSI 18 (level, low) -> IRQ 18 [ 55.659102] Audigy2 value: Special config. [ 57.257005] w83627ehf: Found W83627EHG chip at 0x290 [ 58.250017] r8169: eth0: link up [ 58.250023] r8169: eth0: link up [ 58.784830] NET: Registered protocol family 17