Hi,
I have an Alive -NF5-esata2+. AM2 board with dual core AMD64 cpu.
Problem exists with latest bios 1.90 and its predecessor 1.80.
This board with nforce 520 chipset (MCP65) has three possible settings for the
sata controller:
non-raid
raid
ahci.
My default is non-raid.
With 2.6.24 based kernels I get this on cold boot:
[ 49.176044] Driver 'sd' needs updating - please use bus_type methods
[ 49.176117] ahci 0000:00:0a.0: version 3.0
[ 49.176291] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 23
[ 49.176335] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LSA0] -> GSI 23
(level, low) -> IRQ 23
[ 50.176871] ahci 0000:00:0a.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf
impl IDE mode
[ 50.176922] ahci 0000:00:0a.0: flags: 64bit sntf led clo pmp pio
[ 50.176962] PCI: Setting latency timer of device 0000:00:0a.0 to 64
[ 50.177163] scsi0 : ahci
[ 50.177259] scsi1 : ahci
[ 50.177325] scsi2 : ahci
[ 50.177392] scsi3 : ahci
[ 50.177480] ata1: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc100
irq 315
[ 50.177528] ata2: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc180
irq 315
[ 50.177575] ata3: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc200
irq 315
[ 50.177623] ata4: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc280
irq 315
[ 50.808824] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 80.743754] ata1.00: qc timeout (cmd 0xec)
[ 80.743792] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[ 80.743831] ata1: failed to recover some devices, retrying in 5 secs
[ 86.368194] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 86.368803] ata1.00: ATA-7: WDC WD1600JS-00MHB1, 10.02E01, max UDMA/133
[ 86.368846] ata1.00: 312581808 sectors, multi 16: LBA48
[ 86.369491] ata1.00: configured for UDMA/133
[ 87.000153] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 87.020703] ata2.00: ATA-8: SAMSUNG HD501LJ, CR100-12, max UDMA7
[ 87.020742] ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 87.022737] ata2.00: configured for UDMA/133
[ 87.339415] ata3: SATA link down (SStatus 0 SControl 300)
[ 87.658721] ata4: SATA link down (SStatus 0 SControl 300)
[ 87.658810] scsi 0:0:0:0: Direct-Access ATA WDC WD1600JS-00M 10.0
PQ: 0 ANSI: 5
[ 87.658917] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042
MB)
[ 87.658962] sd 0:0:0:0: [sda] Write Protect is off
[ 87.659000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 87.659008] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 87.659078] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042
MB)
[ 87.659121] sd 0:0:0:0: [sda] Write Protect is off
[ 87.659159] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 87.659166] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 87.659215] sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
[ 87.696698] sd 0:0:0:0: [sda] Attached SCSI disk
[ 87.696832] scsi 1:0:0:0: Direct-Access ATA SAMSUNG HD501LJ CR10
PQ: 0 ANSI: 5
[ 87.696940] sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108
MB)
[ 87.696985] sd 1:0:0:0: [sdb] Write Protect is off
[ 87.697022] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 87.697031] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 87.697101] sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108
MB)
[ 87.697144] sd 1:0:0:0: [sdb] Write Protect is off
[ 87.697182] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 87.697189] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 87.697238] sdb: sdb1 sdb2
[ 87.720300] sd 1:0:0:0: [sdb] Attached SCSI disk
---------------------------------------------------------------------------------------
and this on reboots:
30.984720] ahci 0000:00:0a.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf
impl IDE mode
[ 30.984771] ahci 0000:00:0a.0: flags: 64bit sntf led clo pmp pio
[ 30.984811] PCI: Setting latency timer of device 0000:00:0a.0 to 64
[ 30.985012] scsi0 : ahci
[ 30.985108] scsi1 : ahci
[ 30.985174] scsi2 : ahci
[ 30.985241] scsi3 : ahci
[ 30.985329] ata1: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc100
irq 315
[ 30.985377] ata2: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc180
irq 315
[ 30.985425] ata3: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc200
irq 315
[ 30.985472] ata4: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc280
irq 315
[ 36.619135] ata1: port is slow to respond, please be patient (Status 0xd0)
[ 40.982984] ata1: softreset failed (device not ready)
[ 41.614947] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 41.615582] ata1.00: ATA-7: WDC WD1600JS-00MHB1, 10.02E01, max UDMA/133
[ 41.615625] ata1.00: 312581808 sectors, multi 16: LBA48
[ 41.616251] ata1.00: configured for UDMA/133
[ 42.246907] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 42.250073] ata2.00: ATA-8: SAMSUNG HD501LJ, CR100-12, max UDMA7
[ 42.250113] ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 42.252112] ata2.00: configured for UDMA/133
[ 42.569539] ata3: SATA link down (SStatus 0 SControl 300)
[ 42.888845] ata4: SATA link down (SStatus 0 SControl 300)
[ 42.888934] scsi 0:0:0:0: Direct-Access ATA WDC WD1600JS-00M 10.0
PQ: 0 ANSI: 5
[ 42.889041] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042
MB)
[ 42.889086] sd 0:0:0:0: [sda] Write Protect is off
[ 42.889124] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 42.889132] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 42.889202] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042
MB)
[ 42.889246] sd 0:0:0:0: [sda] Write Protect is off
[ 42.889284] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 42.889291] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 42.889340] sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
[ 42.925936] sd 0:0:0:0: [sda] Attached SCSI disk
[ 42.926071] scsi 1:0:0:0: Direct-Access ATA SAMSUNG HD501LJ CR10
PQ: 0 ANSI: 5
[ 42.926180] sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108
MB)
[ 42.926224] sd 1:0:0:0: [sdb] Write Protect is off
[ 42.926262] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 42.926271] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 42.926346] sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108
MB)
[ 42.926389] sd 1:0:0:0: [sdb] Write Protect is off
[ 42.926427] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 42.926434] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 42.926484] sdb: sdb1 sdb2
[ 42.955833] sd 1:0:0:0: [sdb] Attached SCSI disk
----------------------------------------------------------------------------------------
with 2.6.23.11 it looks like this:
[ 90.956853] ide: Assuming 33MHz system bus speed for PIO modes; override
with idebus=xx
[ 90.957166] NFORCE-MCP65: IDE controller at PCI slot 0000:00:09.0
[ 90.957335] NFORCE-MCP65: chipset revision 161
[ 90.957494] NFORCE-MCP65: not 100% native mode: will probe irqs later
[ 90.957658] NFORCE-MCP65: 0000:00:09.0 (rev a1) UDMA133 controller
[ 90.957820] ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA,
hdb:pio
[ 90.958166] Probing IDE interface ide0...
[ 91.246150] hda: SAMSUNG SP1213N, ATA DISK drive
[ 91.888005] hda: selected mode 0x45
[ 91.888070] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 91.890652] hda: max request size: 512KiB
[ 91.890861] hda: 234493056 sectors (120060 MB) w/8192KiB Cache,
CHS=16383/255/63, UDMA(100)
[ 91.891601] hda: cache flushes supported
[ 91.891777] hda: hda1 hda2 hda3 < hda5 hda6 hda7 >
[ 91.931121] ahci 0000:00:0a.0: version 2.3
[ 91.931299] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 23
[ 91.931465] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LSA0] -> GSI 23
(level, low) -> IRQ 23
[ 92.935591] ahci 0000:00:0a.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf
impl IDE mode
[ 92.935888] ahci 0000:00:0a.0: flags: 64bit sntf led clo pmp pio
[ 92.936049] PCI: Setting latency timer of device 0000:00:0a.0 to 64
[ 92.936263] scsi0 : ahci
[ 92.936486] scsi1 : ahci
[ 92.936677] scsi2 : ahci
[ 92.936867] scsi3 : ahci
[ 92.937048] ata1: SATA max UDMA/133 cmd 0xffffc20000020100 ctl
0x0000000000000000 bmdma 0x0000000000000000 irq 315
[ 92.937342] ata2: SATA max UDMA/133 cmd 0xffffc20000020180 ctl
0x0000000000000000 bmdma 0x0000000000000000 irq 315
[ 92.937636] ata3: SATA max UDMA/133 cmd 0xffffc20000020200 ctl
0x0000000000000000 bmdma 0x0000000000000000 irq 315
[ 92.937930] ata4: SATA max UDMA/133 cmd 0xffffc20000020280 ctl
0x0000000000000000 bmdma 0x0000000000000000 irq 315
[ 93.411080] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 93.411883] ata1.00: ATA-7: WDC WD1600JS-00MHB1, 10.02E01, max UDMA/133
[ 93.412045] ata1.00: 312581808 sectors, multi 16: LBA48
[ 93.412797] ata1.00: configured for UDMA/133
[ 93.727032] ata2: SATA link down (SStatus 0 SControl 300)
[ 94.042987] ata3: SATA link down (SStatus 0 SControl 300)
[ 94.358941] ata4: SATA link down (SStatus 0 SControl 300)
[ 94.359249] scsi 0:0:0:0: Direct-Access ATA WDC WD1600JS-00M 10.0
PQ: 0 ANSI: 5
[ 94.359599] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042
MB)
[ 94.359765] sd 0:0:0:0: [sda] Write Protect is off
[ 94.359925] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 94.359933] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 94.360249] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042
MB)
[ 94.360414] sd 0:0:0:0: [sda] Write Protect is off
[ 94.360573] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 94.360581] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 94.360873] sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
[ 94.402906] sd 0:0:0:0: [sda] Attached SCSI disk
[ 94.403107] sd 0:0:0:0: Attached scsi generic sg0 type 0
---------------------------------------------------------------------------------------
I removed the pata-disk and the drivers some days ago - but that has had no
influence on the problem. The delay was there with the pata-drive and drivers
too. There are some changes in the config - but even with the 2.6.3.11 config
on a 2.6.24 and make oldconfig showed the delays.
If I change from 'non raid' to AHCI (because the handbook says that is the way
to get NCQ working) boot hangs for looong time and no harddisks are found:
(dmesg from systemrescuecd 1.0)
ahci 0000:00:0a.0: version 3.0
ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LSA0] -> GSI 23 (level, low) ->
IRQ 18
ahci 0000:00:0a.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
ahci 0000:00:0a.0: flags: 64bit sntf led clo pmp pio
PCI: Setting latency timer of device 0000:00:0a.0 to 64
scsi3 : ahci
scsi4 : ahci
scsi5 : ahci
scsi6 : ahci
ata1: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc100 irq 218
ata2: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc180 irq 218
ata3: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc200 irq 218
ata4: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc280 irq 218
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
APIC error on CPU0: 00(40)
scsi_scan_2 used greatest stack depth: 2868 bytes left
ata1.00: qc timeout (cmd 0xec)
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata1: failed to recover some devices, retrying in 5 secs
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
APIC error on CPU0: 40(40)
ata1.00: qc timeout (cmd 0xec)
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata1: failed to recover some devices, retrying in 5 secs
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
APIC error on CPU0: 40(40)
ata1.00: qc timeout (cmd 0xec)
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata1: failed to recover some devices, retrying in 5 secs
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
APIC error on CPU0: 40(40)
ata2.00: qc timeout (cmd 0xec)
ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata2: failed to recover some devices, retrying in 5 secs
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
APIC error on CPU0: 40(40)
ata2.00: qc timeout (cmd 0xec)
ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata2: failed to recover some devices, retrying in 5 secs
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
APIC error on CPU0: 40(40)
ata2.00: qc timeout (cmd 0xec)
ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata2: failed to recover some devices, retrying in 5 secs
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
pata_amd 0000:00:09.0: version 0.3.10
PCI: Setting latency timer of device 0000:00:09.0 to 64
scsi7 : pata_amd
scsi8 : pata_amd
ata5: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
ata6: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
I tried systemrescuecd with the 'noapic' option - same result. Long hangs, no
disks found.
lspci
00:00.0 RAM memory: nVidia Corporation MCP65 Memory Controller (rev a1)
00:01.0 ISA bridge: nVidia Corporation MCP65 LPC Bridge (rev a2)
00:01.1 SMBus: nVidia Corporation MCP65 SMBus (rev a1)
00:01.2 RAM memory: nVidia Corporation MCP65 Memory Controller (rev a1)
00:02.0 USB Controller: nVidia Corporation MCP65 USB Controller (rev a1)
00:02.1 USB Controller: nVidia Corporation MCP65 USB Controller (rev a1)
00:08.0 PCI bridge: nVidia Corporation MCP65 PCI bridge (rev a1)
00:09.0 IDE interface: nVidia Corporation MCP65 IDE (rev a1)
00:0a.0 IDE interface: nVidia Corporation MCP65 SATA Controller (rev a1)
00:0b.0 PCI bridge: nVidia Corporation Unknown device 045b (rev a1)
00:0c.0 PCI bridge: nVidia Corporation MCP65 PCI Express bridge (rev a1)
00:0d.0 PCI bridge: nVidia Corporation MCP65 PCI Express bridge (rev a1)
00:0e.0 PCI bridge: nVidia Corporation MCP65 PCI Express bridge (rev a1)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM
Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control
01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI
Express Gigabit Ethernet controller (rev 01)
02:08.0 SCSI storage controller: Adaptec AHA-2944UW / AIC-7884U (rev 01)
02:09.0 Multimedia audio controller: Creative Labs SB0400 Audigy2 Value
04:00.0 VGA compatible controller: nVidia Corporation Unknown device 0402 (rev
a1)
dmesg
[ 0.000000] Linux version 2.6.24.2reiser4 (root@energy) (gcc version 4.2.3
(Gentoo 4.2.3 p1.0)) #6 SMP Tue Mar 4 17:28:59 CET 2008
[ 0.000000] Command line: root=/dev/sda3 nmi_watchdog=0 console=tty6
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e6000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 00000000cffb0000 (usable)
[ 0.000000] BIOS-e820: 00000000cffb0000 - 00000000cffc0000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000cffc0000 - 00000000cfff0000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000cfff0000 - 00000000d0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff380000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 0000000130000000 (usable)
[ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 256 used
[ 0.000000] Entering add_active_range(0, 256, 851888) 1 entries of 256 used
[ 0.000000] Entering add_active_range(0, 1048576, 1245184) 2 entries of 256
used
[ 0.000000] end_pfn_map = 1245184
[ 0.000000] DMI present.
[ 0.000000] ACPI: RSDP 000F98E0, 0014 (r0 ACPIAM)
[ 0.000000] ACPI: RSDT CFFB0000, 003C (r1 A M I OEMRSDT 12000731 MSFT
97)
[ 0.000000] ACPI: FACP CFFB0200, 0084 (r2 A_M_I OEMFACP 12000601 MSFT
97)
[ 0.000000] ACPI: DSDT CFFB0450, 4FFA (r1 ASR19 ASR19186 186 INTL
20051117)
[ 0.000000] ACPI: FACS CFFC0000, 0040
[ 0.000000] ACPI: APIC CFFB0390, 0080 (r1 A M I OEMAPIC 12000731 MSFT
97)
[ 0.000000] ACPI: MCFG CFFB0410, 003C (r1 A M I OEMMCFG 12000731 MSFT
97)
[ 0.000000] ACPI: OEMB CFFC0040, 0060 (r1 A M I AMI_OEM 12000731 MSFT
97)
[ 0.000000] ACPI: HPET CFFB5450, 0038 (r1 A M I OEMHPET0 12000731 MSFT
97)
[ 0.000000] ACPI: SSDT CFFB5490, 030E (r1 A M I POWERNOW 1 AMD
1)
[ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 256 used
[ 0.000000] Entering add_active_range(0, 256, 851888) 1 entries of 256 used
[ 0.000000] Entering add_active_range(0, 1048576, 1245184) 2 entries of 256
used
[ 0.000000] No mptable found.
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] DMA32 4096 -> 1048576
[ 0.000000] Normal 1048576 -> 1245184
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[3] active PFN ranges
[ 0.000000] 0: 0 -> 159
[ 0.000000] 0: 256 -> 851888
[ 0.000000] 0: 1048576 -> 1245184
[ 0.000000] On node 0 totalpages: 1048399
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 856 pages reserved
[ 0.000000] DMA zone: 3087 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 14280 pages used for memmap
[ 0.000000] DMA32 zone: 833512 pages, LIFO batch:31
[ 0.000000] Normal zone: 2688 pages used for memmap
[ 0.000000] Normal zone: 193920 pages, LIFO batch:31
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] ACPI: PM-Timer IO Port: 0x2008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 (Bootup-CPU)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] Processor #1
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] ACPI: IRQ14 used by override.
[ 0.000000] ACPI: IRQ15 used by override.
[ 0.000000] Setting APIC routing to flat
[ 0.000000] ACPI: HPET id: 0x10de8201 base: 0xfed00000
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] swsusp: Registered nosave memory region: 000000000009f000 -
00000000000a0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 -
00000000000e6000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000e6000 -
0000000000100000
[ 0.000000] swsusp: Registered nosave memory region: 00000000cffb0000 -
00000000cffc0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000cffc0000 -
00000000cfff0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000cfff0000 -
00000000d0000000
[ 0.000000] swsusp: Registered nosave memory region: 00000000d0000000 -
00000000fec00000
[ 0.000000] swsusp: Registered nosave memory region: 00000000fec00000 -
00000000fec01000
[ 0.000000] swsusp: Registered nosave memory region: 00000000fec01000 -
00000000fee00000
[ 0.000000] swsusp: Registered nosave memory region: 00000000fee00000 -
00000000fef00000
[ 0.000000] swsusp: Registered nosave memory region: 00000000fef00000 -
00000000ff380000
[ 0.000000] swsusp: Registered nosave memory region: 00000000ff380000 -
0000000100000000
[ 0.000000] Allocating PCI resources starting at d4000000 (gap:
d0000000:2ec00000)
[ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] PERCPU: Allocating 31408 bytes of per cpu data
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total
pages: 1030519
[ 0.000000] Kernel command line: root=/dev/sda3 nmi_watchdog=0 console=tty6
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[ 0.000000] hpet clockevent registered
[ 0.000000] TSC calibrated against HPET
[ 48.747446] Marking TSC unstable due to TSCs unsynchronized
[ 48.747447] time.c: Detected 3013.888 MHz processor.
[ 48.751279] Console: colour VGA+ 80x25
[ 48.751281] console [tty6] enabled
[ 48.755890] Dentry cache hash table entries: 524288 (order: 10, 4194304
bytes)
[ 48.758116] Inode-cache hash table entries: 262144 (order: 9, 2097152
bytes)
[ 48.758884] Checking aperture...
[ 48.758922] CPU 0: aperture @ ecc8000000 size 32 MB
[ 48.758959] Aperture too small (32 MB)
[ 48.764827] No AGP bridge found
[ 48.764863] Your BIOS doesn't leave a aperture memory hole
[ 48.764901] Please enable the IOMMU option in the BIOS setup
[ 48.764939] This costs you 64 MB of RAM
[ 48.790106] Mapping aperture over 65536 KB of RAM @ 8000000
[ 48.813687] Memory: 4049936k/4980736k available (2204k kernel code, 143440k
reserved, 681k data, 172k init)
[ 48.813756] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=2,
Nodes=1
[ 48.893771] Calibrating delay using timer specific routine.. 6034.65
BogoMIPS (lpj=10053840)
[ 48.893864] Mount-cache hash table entries: 256
[ 48.893972] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64
bytes/line)
[ 48.894012] CPU: L2 Cache: 1024K (64 bytes/line)
[ 48.894050] CPU: Physical Processor ID: 0
[ 48.894086] CPU: Processor Core ID: 0
[ 48.894139] SMP alternatives: switching to UP code
[ 48.894504] ACPI: Core revision 20070126
[ 48.929680] Using local APIC timer interrupts.
[ 48.962824] APIC timer calibration result 12557873
[ 48.962826] Detected 12.557 MHz APIC timer.
[ 48.962910] SMP alternatives: switching to SMP code
[ 48.963141] Booting processor 1/2 APIC 0x1
[ 48.973258] Initializing CPU#1
[ 49.056020] Calibrating delay using timer specific routine.. 6030.92
BogoMIPS (lpj=10046281)
[ 49.056024] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64
bytes/line)
[ 49.056026] CPU: L2 Cache: 1024K (64 bytes/line)
[ 49.056027] CPU: Physical Processor ID: 0
[ 49.056028] CPU: Processor Core ID: 1
[ 49.056109] AMD Athlon(tm) 64 X2 Dual Core Processor 6000+ stepping 03
[ 49.056167] Brought up 2 CPUs
[ 49.056624] net_namespace: 120 bytes
[ 49.056866] NET: Registered protocol family 16
[ 49.056978] ACPI: bus type pci registered
[ 49.057060] PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
[ 49.057099] PCI: Not using MMCONFIG.
[ 49.057135] PCI: Using configuration type 1
[ 49.059381] ACPI: EC: Look up EC in DSDT
[ 49.062825] ACPI: Interpreter enabled
[ 49.062863] ACPI: (supports S0 S1 S3 S4 S5)
[ 49.063033] ACPI: Using IOAPIC for interrupt routing
[ 49.063242] Error attaching device data
[ 49.063281] Error attaching device data
[ 49.063320] Error attaching device data
[ 49.063359] Error attaching device data
[ 49.068281] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 49.068803] PCI: Transparent bridge - 0000:00:08.0
[ 49.069095] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 49.069228] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[ 49.069326] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR10._PRT]
[ 49.069382] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR11._PRT]
[ 49.069438] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR13._PRT]
[ 49.069494] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR12._PRT]
[ 49.073455] ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *11
[ 49.073793] ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *5
[ 49.074127] ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *0,
disabled.
[ 49.074487] ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *0,
disabled.
[ 49.074847] ACPI: PCI Interrupt Link [LNEA] (IRQs 16 17 18 19) *0,
disabled.
[ 49.075207] ACPI: PCI Interrupt Link [LNEB] (IRQs 16 17 18 19) *10
[ 49.075541] ACPI: PCI Interrupt Link [LNEC] (IRQs 16 17 18 19) *0,
disabled.
[ 49.075902] ACPI: PCI Interrupt Link [LNED] (IRQs 16 17 18 19) *10
[ 49.076239] ACPI: PCI Interrupt Link [LUB0] (IRQs 20 21 22 23) *5
[ 49.076573] ACPI: PCI Interrupt Link [LMAD] (IRQs 20 21 22 23) *0,
disabled.
[ 49.076933] ACPI: PCI Interrupt Link [LUB2] (IRQs 20 21 22 23) *7
[ 49.077267] ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *0,
disabled.
[ 49.077628] ACPI: PCI Interrupt Link [LAZA] (IRQs 20 21 22 23) *0,
disabled.
[ 49.077988] ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *11
[ 49.078322] ACPI: PCI Interrupt Link [LPMU] (IRQs 20 21 22 23) *0,
disabled.
[ 49.078683] ACPI: PCI Interrupt Link [LSA0] (IRQs 20 21 22 23) *15
[ 49.079017] ACPI: PCI Interrupt Link [LSA1] (IRQs 20 21 22 23) *0,
disabled.
[ 49.079415] ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22 23) *0,
disabled.
[ 49.079776] ACPI: PCI Interrupt Link [UB11] (IRQs 20 21 22 23) *0,
disabled.
[ 49.080137] ACPI: PCI Interrupt Link [UB12] (IRQs 20 21 22 23) *0,
disabled.
[ 49.080456] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 49.080509] pnp: PnP ACPI init
[ 49.080548] ACPI: bus type pnp registered
[ 49.083088] pnp: PnP ACPI: found 13 devices
[ 49.083125] ACPI: ACPI bus type pnp unregistered
[ 49.083244] SCSI subsystem initialized
[ 49.083300] libata version 3.00 loaded.
[ 49.083353] usbcore: registered new interface driver usbfs
[ 49.083407] usbcore: registered new interface driver hub
[ 49.083464] usbcore: registered new device driver usb
[ 49.083546] PCI: Using ACPI for IRQ routing
[ 49.083584] PCI: If a device doesn't work, try "pci=routeirq". If it
helps, post a report
[ 49.092621] PCI-DMA: Disabling AGP.
[ 49.093359] PCI-DMA: aperture base @ 8000000 size 65536 KB
[ 49.093401] PCI-DMA: using GART IOMMU.
[ 49.093441] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
[ 49.093600] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31
[ 49.093739] hpet0: 3 32-bit timers, 25000000 Hz
[ 49.095903] Time: hpet clocksource has been installed.
[ 49.095951] Switched to high resolution mode on CPU 0
[ 49.096038] Switched to high resolution mode on CPU 1
[ 49.102635] system 00:05: ioport range 0x4d0-0x4d1 has been reserved
[ 49.102675] system 00:05: ioport range 0x800-0x80f has been reserved
[ 49.102714] system 00:05: ioport range 0x2000-0x207f has been reserved
[ 49.102754] system 00:05: ioport range 0x2080-0x20ff has been reserved
[ 49.106152] system 00:05: ioport range 0x2400-0x247f has been reserved
[ 49.106192] system 00:05: ioport range 0x2480-0x24ff has been reserved
[ 49.106231] system 00:05: ioport range 0x2800-0x287f has been reserved
[ 49.106270] system 00:05: ioport range 0x2880-0x28ff has been reserved
[ 49.106309] system 00:05: ioport range 0x2c00-0x2c7f has been reserved
[ 49.106349] system 00:05: ioport range 0x2c80-0x2cff has been reserved
[ 49.106389] system 00:05: iomem range 0x0-0x0 could not be reserved
[ 49.106428] system 00:05: iomem range 0xfee01000-0xfeefffff has been
reserved
[ 49.106472] system 00:07: iomem range 0xfec00000-0xfec00fff could not be
reserved
[ 49.106520] system 00:07: iomem range 0xfee00000-0xfee00fff could not be
reserved
[ 49.106570] system 00:0a: ioport range 0x290-0x29f has been reserved
[ 49.106613] system 00:0b: iomem range 0xe0000000-0xefffffff has been
reserved
[ 49.106658] system 00:0c: iomem range 0x0-0x9ffff could not be reserved
[ 49.106698] system 00:0c: iomem range 0xc0000-0xcffff has been reserved
[ 49.106740] system 00:0c: iomem range 0xe0000-0xfffff could not be reserved
[ 49.106780] system 00:0c: iomem range 0x100000-0xcfffffff could not be
reserved
[ 49.106827] system 00:0c: iomem range 0xff380000-0xffffffff could not be
reserved
[ 49.107108] PCI: Bridge: 0000:00:08.0
[ 49.107145] IO window: d000-dfff
[ 49.107182] MEM window: f9f00000-f9ffffff
[ 49.107219] PREFETCH window: disabled.
[ 49.107257] PCI: Bridge: 0000:00:0b.0
[ 49.107293] IO window: c000-cfff
[ 49.107330] MEM window: f9e00000-f9efffff
[ 49.107367] PREFETCH window: disabled.
[ 49.107404] PCI: Bridge: 0000:00:0c.0
[ 49.107440] IO window: disabled.
[ 49.107476] MEM window: disabled.
[ 49.107512] PREFETCH window: disabled.
[ 49.107549] PCI: Bridge: 0000:00:0d.0
[ 49.107585] IO window: e000-efff
[ 49.107622] MEM window: fa000000-febfffff
[ 49.107659] PREFETCH window: d0000000-dfffffff
[ 49.107697] PCI: Bridge: 0000:00:0e.0
[ 49.107733] IO window: disabled.
[ 49.107769] MEM window: disabled.
[ 49.107805] PREFETCH window: disabled.
[ 49.107848] PCI: Setting latency timer of device 0000:00:08.0 to 64
[ 49.107857] PCI: Setting latency timer of device 0000:00:0b.0 to 64
[ 49.107862] PCI: Setting latency timer of device 0000:00:0c.0 to 64
[ 49.107866] PCI: Setting latency timer of device 0000:00:0d.0 to 64
[ 49.107871] PCI: Setting latency timer of device 0000:00:0e.0 to 64
[ 49.107877] NET: Registered protocol family 2
[ 49.139202] IP route cache hash table entries: 131072 (order: 8, 1048576
bytes)
[ 49.139805] TCP established hash table entries: 262144 (order: 10, 4194304
bytes)
[ 49.141228] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 49.141693] TCP: Hash tables configured (established 262144 bind 65536)
[ 49.141733] TCP reno registered
[ 49.149967] Loading Reiser4. See www.namesys.com for a description of
Reiser4.
[ 49.150075] Block layer SCSI generic (bsg) driver version 0.4 loaded (major
254)
[ 49.150123] io scheduler noop registered
[ 49.150161] io scheduler cfq registered (default)
[ 49.150855] Boot video device is 0000:04:00.0
[ 49.150958] PCI: Setting latency timer of device 0000:00:0b.0 to 64
[ 49.150975] assign_interrupt_mode Found MSI capability
[ 49.151029] Allocate Port Service[0000:00:0b.0:pcie00]
[ 49.151071] PCI: Setting latency timer of device 0000:00:0c.0 to 64
[ 49.151087] assign_interrupt_mode Found MSI capability
[ 49.151135] Allocate Port Service[0000:00:0c.0:pcie00]
[ 49.151172] PCI: Setting latency timer of device 0000:00:0d.0 to 64
[ 49.151187] assign_interrupt_mode Found MSI capability
[ 49.151235] Allocate Port Service[0000:00:0d.0:pcie00]
[ 49.151274] PCI: Setting latency timer of device 0000:00:0e.0 to 64
[ 49.151290] assign_interrupt_mode Found MSI capability
[ 49.151338] Allocate Port Service[0000:00:0e.0:pcie00]
[ 49.151515] input: Power Button (FF) as /class/input/input0
[ 49.151553] ACPI: Power Button (FF) [PWRF]
[ 49.151638] input: Power Button (CM) as /class/input/input1
[ 49.151676] ACPI: Power Button (CM) [PWRB]
[ 49.151812] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor
Device is not present [20070126]
[ 49.151917] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor
Device is not present [20070126]
[ 49.175824] Real Time Clock Driver v1.12ac
[ 49.175942] hpet_resources: 0xfed00000 is busy
[ 49.175960] Linux agpgart interface v0.102
[ 49.176044] Driver 'sd' needs updating - please use bus_type methods
[ 49.176117] ahci 0000:00:0a.0: version 3.0
[ 49.176291] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 23
[ 49.176335] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LSA0] -> GSI 23
(level, low) -> IRQ 23
[ 50.176871] ahci 0000:00:0a.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf
impl IDE mode
[ 50.176922] ahci 0000:00:0a.0: flags: 64bit sntf led clo pmp pio
[ 50.176962] PCI: Setting latency timer of device 0000:00:0a.0 to 64
[ 50.177163] scsi0 : ahci
[ 50.177259] scsi1 : ahci
[ 50.177325] scsi2 : ahci
[ 50.177392] scsi3 : ahci
[ 50.177480] ata1: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc100
irq 315
[ 50.177528] ata2: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc180
irq 315
[ 50.177575] ata3: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc200
irq 315
[ 50.177623] ata4: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc280
irq 315
[ 50.808824] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 80.743754] ata1.00: qc timeout (cmd 0xec)
[ 80.743792] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[ 80.743831] ata1: failed to recover some devices, retrying in 5 secs
[ 86.368194] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 86.368803] ata1.00: ATA-7: WDC WD1600JS-00MHB1, 10.02E01, max UDMA/133
[ 86.368846] ata1.00: 312581808 sectors, multi 16: LBA48
[ 86.369491] ata1.00: configured for UDMA/133
[ 87.000153] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 87.020703] ata2.00: ATA-8: SAMSUNG HD501LJ, CR100-12, max UDMA7
[ 87.020742] ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 87.022737] ata2.00: configured for UDMA/133
[ 87.339415] ata3: SATA link down (SStatus 0 SControl 300)
[ 87.658721] ata4: SATA link down (SStatus 0 SControl 300)
[ 87.658810] scsi 0:0:0:0: Direct-Access ATA WDC WD1600JS-00M 10.0
PQ: 0 ANSI: 5
[ 87.658917] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042
MB)
[ 87.658962] sd 0:0:0:0: [sda] Write Protect is off
[ 87.659000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 87.659008] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 87.659078] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042
MB)
[ 87.659121] sd 0:0:0:0: [sda] Write Protect is off
[ 87.659159] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 87.659166] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 87.659215] sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
[ 87.696698] sd 0:0:0:0: [sda] Attached SCSI disk
[ 87.696832] scsi 1:0:0:0: Direct-Access ATA SAMSUNG HD501LJ CR10
PQ: 0 ANSI: 5
[ 87.696940] sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108
MB)
[ 87.696985] sd 1:0:0:0: [sdb] Write Protect is off
[ 87.697022] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 87.697031] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 87.697101] sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108
MB)
[ 87.697144] sd 1:0:0:0: [sdb] Write Protect is off
[ 87.697182] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 87.697189] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 87.697238] sdb: sdb1 sdb2
[ 87.720300] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 87.720614] ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 22
[ 87.720659] ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUB2] -> GSI 22
(level, low) -> IRQ 22
[ 87.720952] PCI: Setting latency timer of device 0000:00:02.1 to 64
[ 87.720956] ehci_hcd 0000:00:02.1: EHCI Host Controller
[ 87.721072] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus
number 1
[ 87.721146] ehci_hcd 0000:00:02.1: debug port 1
[ 87.721185] PCI: cache line size of 64 is not supported by device
0000:00:02.1
[ 87.721193] ehci_hcd 0000:00:02.1: irq 22, io mem 0xf9dfec00
[ 87.729429] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10
Dec 2004
[ 87.729591] usb usb1: configuration #1 chosen from 1 choice
[ 87.729657] hub 1-0:1.0: USB hub found
[ 87.729698] hub 1-0:1.0: 10 ports detected
[ 87.831809] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64
irq 1,12
[ 87.834655] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 87.834694] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 87.890390] input: AT Translated Set 2 keyboard as /class/input/input2
[ 88.057853] usb 1-3: new high speed USB device using ehci_hcd and address 2
[ 88.182269] usb 1-3: configuration #1 chosen from 1 choice
[ 88.182606] hub 1-3:1.0: USB hub found
[ 88.182959] hub 1-3:1.0: 4 ports detected
[ 88.510234] usb 1-5: new high speed USB device using ehci_hcd and address 3
[ 88.639370] usb 1-5: configuration #1 chosen from 1 choice
[ 88.826522] usb 1-3.1: new low speed USB device using ehci_hcd and address
4
[ 88.928973] usb 1-3.1: configuration #1 chosen from 1 choice
[ 89.122483] usb 1-3.4: new high speed USB device using ehci_hcd and address
5
[ 89.195695] usb 1-3.4: device descriptor read/64, error -71
[ 89.371925] usb 1-3.4: device descriptor read/64, error -71
[ 89.541544] usb 1-3.4: new high speed USB device using ehci_hcd and address
6
[ 89.614755] usb 1-3.4: device descriptor read/64, error -71
[ 89.790985] usb 1-3.4: device descriptor read/64, error -71
[ 89.960730] usb 1-3.4: new high speed USB device using ehci_hcd and address
7
[ 90.366204] usb 1-3.4: device not accepting address 7, error -71
[ 90.432921] usb 1-3.4: new high speed USB device using ehci_hcd and address
8
[ 90.838511] usb 1-3.4: device not accepting address 8, error -71
[ 90.843129] input: Logitech USB Receiver as /class/input/input3
[ 90.859316] input: USB HID v1.11 Mouse [Logitech USB Receiver] on
usb-0000:00:02.1-3.1
[ 90.865040] input: Logitech USB Receiver as /class/input/input4
[ 90.885926] input: USB HID v1.11 Device [Logitech USB Receiver] on
usb-0000:00:02.1-3.1
[ 90.886029] usbcore: registered new interface driver usbhid
[ 90.886068] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 90.886113] TCP cubic registered
[ 90.886152] NET: Registered protocol family 1
[ 90.886209] powernow-k8: Found 1 AMD Athlon(tm) 64 X2 Dual Core Processor
6000+ processors (2 cpu cores) (version 2.20.00)
[ 90.886262] powernow-k8: 0 : fid 0x16 (3000 MHz), vid 0x6
[ 90.886301] powernow-k8: 1 : fid 0x14 (2800 MHz), vid 0x8
[ 90.886339] powernow-k8: 2 : fid 0x12 (2600 MHz), vid 0xa
[ 90.886378] powernow-k8: 3 : fid 0x10 (2400 MHz), vid 0xc
[ 90.886416] powernow-k8: 4 : fid 0xe (2200 MHz), vid 0xe
[ 90.886454] powernow-k8: 5 : fid 0xc (2000 MHz), vid 0x10
[ 90.889850] powernow-k8: 6 : fid 0xa (1800 MHz), vid 0x10
[ 90.889889] powernow-k8: 7 : fid 0x2 (1000 MHz), vid 0x12
[ 90.900783] ReiserFS: sda3: found reiserfs format "3.6" with standard
journal
[ 90.900825] ReiserFS: sda3: using ordered data mode
[ 90.910333] ReiserFS: sda3: journal params: device sda3, size 8192, journal
first block 18, max trans len 1024, max batch 900, max commit age 30, max
trans age 30
[ 90.911226] ReiserFS: sda3: checking transaction log (sda3)
[ 90.954640] ReiserFS: sda3: Using r5 hash to sort names
[ 90.954690] VFS: Mounted root (reiserfs filesystem) readonly.
[ 90.954740] Freeing unused kernel memory: 172k freed
[ 91.040511] Clocksource tsc unstable (delta = -144182848 ns)
[ 92.705141] ReiserFS: sda3: switching to journaled data mode
[ 92.875659] r8169 Gigabit Ethernet driver 2.2LK loaded
[ 92.875868] ACPI: PCI Interrupt Link [LNEB] enabled at IRQ 19
[ 92.875873] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNEB] -> GSI 19
(level, low) -> IRQ 19
[ 92.875881] PCI: Setting latency timer of device 0000:01:00.0 to 64
[ 92.876029] eth0: RTL8168b/8111b at 0xffffc20000172000, 00:19:66:47:f3:cb,
XID 38000000 IRQ 314
[ 93.020810] reiser4: sdb2: found disk format 4.0.0.
[ 101.258255] reiser4: sda6: found disk format 4.0.0.
[ 101.716150] reiser4: sdb1: found disk format 4.0.0.
[ 102.062717] Adding 1951888k swap on /dev/sda2. Priority:-1 extents:1
across:1951888k
[ 103.594035] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 18
[ 103.594041] ACPI: PCI Interrupt 0000:02:09.0[A] -> Link [LNKB] -> GSI 18
(level, low) -> IRQ 18
[ 103.595129] Audigy2 value: Special config.
[ 105.122084] w83627ehf: Found W83627EHG chip at 0x290
[ 106.260422] r8169: eth0: link up
[ 106.260427] r8169: eth0: link up
[ 106.747221] NET: Registered protocol family 17
[ 110.231622] nvidia: module license 'NVIDIA' taints kernel.
[ 110.403019] ACPI: PCI Interrupt Link [LNED] enabled at IRQ 17
[ 110.403027] ACPI: PCI Interrupt 0000:04:00.0[A] -> Link [LNED] -> GSI 17
(level, low) -> IRQ 17
[ 110.403032] PCI: Setting latency timer of device 0000:04:00.0 to 64
[ 110.403117] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 171.06 Wed Feb
20 09:02:26 PST 2008
[ 299.415650] usb 1-3.2: new full speed USB device using ehci_hcd and address
9
[ 299.483823] usb 1-3.2: configuration #1 chosen from 2 choices
[ 299.509674] Initializing USB Mass Storage driver...
[ 299.509771] scsi4 : SCSI emulation for USB Mass Storage devices
[ 299.509315] usb-storage: device found at 9
[ 299.509318] usb-storage: waiting for device to settle before scanning
[ 299.509821] usbcore: registered new interface driver usb-storage
[ 299.509823] USB Mass Storage support registered.
[ 302.973619] scsi 4:0:0:0: Direct-Access Motorola Motorola Phone 2.31
PQ: 0 ANSI: 2
[ 303.092568] sd 4:0:0:0: [sdc] 979456 512-byte hardware sectors (501 MB)
[ 303.100559] sd 4:0:0:0: [sdc] Write Protect is off
[ 303.100563] sd 4:0:0:0: [sdc] Mode Sense: 0b 00 00 08
[ 303.100574] sd 4:0:0:0: [sdc] Assuming drive cache: write through
[ 303.130402] sd 4:0:0:0: [sdc] 979456 512-byte hardware sectors (501 MB)
[ 303.138545] sd 4:0:0:0: [sdc] Write Protect is off
[ 303.138548] sd 4:0:0:0: [sdc] Mode Sense: 0b 00 00 08
[ 303.138550] sd 4:0:0:0: [sdc] Assuming drive cache: write through
[ 303.138552] sdc: sdc1
[ 303.161436] sd 4:0:0:0: [sdc] Attached SCSI removable disk
[ 303.161600] usb-storage: device scan complete
[ 303.176188] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 303.176213] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 303.176238] sd 4:0:0:0: Attached scsi generic sg2 type 0
cat /proc/interrupts
CPU0 CPU1
0: 56 1 IO-APIC-edge timer
1: 11 4589 IO-APIC-edge i8042
8: 0 1 IO-APIC-edge rtc
9: 0 1 IO-APIC-fasteoi acpi
12: 0 3 IO-APIC-edge i8042
17: 26 70891 IO-APIC-fasteoi nvidia
18: 0 0 IO-APIC-fasteoi EMU10K1
22: 49 30631 IO-APIC-fasteoi ehci_hcd:usb1
314: 9 4439 PCI-MSI-edge eth0
315: 32 27847 PCI-MSI-edge ahci
NMI: 0 0 Non-maskable interrupts
LOC: 105026 170031 Local timer interrupts
RES: 27983 12360 Rescheduling interrupts
CAL: 1902 237 function call interrupts
TLB: 5129 4330 TLB shootdowns
TRM: 0 0 Thermal event interrupts
THR: 0 0 Threshold APIC interrupts
SPU: 0 0 Spurious interrupts
ERR: 0
cat /proc/cpuinfo
processor : 0
vendor_id : AuthenticAMD
cpu family : 15
model : 67
model name : AMD Athlon(tm) 64 X2 Dual Core Processor 6000+
stepping : 3
cpu MHz : 2000.000
cache size : 1024 KB
physical id : 0
siblings : 2
core id : 0
cpu cores : 2
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca
cmov pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt rdtscp
lm 3dnowext 3dnow rep_good pni cx16 lahf_lm cmp_legacy svm extapic cr8_legacy
bogomips : 4023.10
TLB size : 1024 4K pages
clflush size : 64
cache_alignment : 64
address sizes : 40 bits physical, 48 bits virtual
power management: ts fid vid ttp tm stc
processor : 1
vendor_id : AuthenticAMD
cpu family : 15
model : 67
model name : AMD Athlon(tm) 64 X2 Dual Core Processor 6000+
stepping : 3
cpu MHz : 2000.000
cache size : 1024 KB
physical id : 0
siblings : 2
core id : 1
cpu cores : 2
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca
cmov pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt rdtscp
lm 3dnowext 3dnow rep_good pni cx16 lahf_lm cmp_legacy svm extapic cr8_legacy
bogomips : 4023.10
TLB size : 1024 4K pages
clflush size : 64
cache_alignment : 64
address sizes : 40 bits physical, 48 bits virtual
power management: ts fid vid ttp tm stc
sh /usr/src/linux/scripts/ver_linux
If some fields are empty or look unusual you may have an old version.
Compare to the current minimal requirements in Documentation/Changes.
Linux energy 2.6.24.2reiser4 #6 SMP Tue Mar 4 17:28:59 CET 2008 x86_64 AMD
Athlon(tm) 64 X2 Dual Core Processor 6000+ AuthenticAMD GNU/Linux
Gnu C 4.2.3
Gnu make 3.81
binutils 2.18.50.0.4.20080208
util-linux 2.13.1
mount 2.13.1
module-init-tools 3.4
e2fsprogs 1.40.6
reiserfsprogs 3.6.19
reiser4progs 1.0.6
PPP 2.4.4
Linux C Library 2.7
Dynamic linker (ldd) 2.7
Procps 3.2.7
Net-tools 1.60
Kbd 1.13
Sh-utils 6.10
udev 118
Modules Loaded nls_iso8859_15 nls_cp850 vfat fat nls_base sg
usb_storage nvidia af_packet k8temp w83627ehf hwmon_vid hwmon i2c_core
snd_seq_midi snd_emu10k1_synth snd_emux_synth snd_seq_virmidi
snd_seq_midi_emul snd_pcm_oss snd_mixer_oss snd_seq_oss snd_seq_midi_event
snd_seq snd_emu10k1 snd_rawmidi firmware_class snd_ac97_codec ac97_bus
snd_pcm snd_seq_device snd_timer snd_page_alloc snd_util_mem snd_hwdep snd
soundcore r8169
If you want/need more information or want me to do something please ask me
directly - I am not subscribed to any of the two lists. If I need to RTFM
please point me to the right FM.
Glück Auf,
Volker
#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.24.2
# Tue Mar 4 17:20:19 2008
#
CONFIG_64BIT=y
# CONFIG_X86_32 is not set
CONFIG_X86_64=y
CONFIG_X86=y
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CMOS_UPDATE=y
CONFIG_CLOCKSOURCE_WATCHDOG=y
CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y
CONFIG_LOCKDEP_SUPPORT=y
CONFIG_STACKTRACE_SUPPORT=y
CONFIG_SEMAPHORE_SLEEPERS=y
CONFIG_MMU=y
CONFIG_ZONE_DMA=y
# CONFIG_QUICKLIST is not set
CONFIG_GENERIC_ISA_DMA=y
CONFIG_GENERIC_IOMAP=y
CONFIG_GENERIC_BUG=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_ARCH_MAY_HAVE_PC_FDC=y
CONFIG_DMI=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
# CONFIG_RWSEM_XCHGADD_ALGORITHM is not set
# CONFIG_ARCH_HAS_ILOG2_U32 is not set
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_GENERIC_TIME_VSYSCALL=y
CONFIG_ARCH_SUPPORTS_OPROFILE=y
CONFIG_ZONE_DMA32=y
CONFIG_ARCH_POPULATES_NODE_MAP=y
CONFIG_AUDIT_ARCH=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_GENERIC_PENDING_IRQ=y
# CONFIG_KTIME_SCALAR is not set
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
#
# General setup
#
CONFIG_EXPERIMENTAL=y
CONFIG_LOCK_KERNEL=y
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION="reiser4"
CONFIG_LOCALVERSION_AUTO=y
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
CONFIG_POSIX_MQUEUE=y
# CONFIG_BSD_PROCESS_ACCT is not set
# CONFIG_TASKSTATS is not set
# CONFIG_USER_NS is not set
# CONFIG_PID_NS is not set
# CONFIG_AUDIT is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=16
# CONFIG_CGROUPS is not set
# CONFIG_FAIR_GROUP_SCHED is not set
CONFIG_SYSFS_DEPRECATED=y
# CONFIG_RELAY is not set
# CONFIG_BLK_DEV_INITRD is not set
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SYSCTL=y
CONFIG_EMBEDDED=y
# CONFIG_UID16 is not set
# CONFIG_SYSCTL_SYSCALL is not set
# CONFIG_KALLSYMS is not set
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_VM_EVENT_COUNTERS=y
# CONFIG_SLUB_DEBUG is not set
# CONFIG_SLAB is not set
CONFIG_SLUB=y
# CONFIG_SLOB is not set
CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
# CONFIG_MODULE_FORCE_UNLOAD is not set
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_KMOD=y
CONFIG_STOP_MACHINE=y
CONFIG_BLOCK=y
# CONFIG_BLK_DEV_IO_TRACE is not set
CONFIG_BLK_DEV_BSG=y
CONFIG_BLOCK_COMPAT=y
#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
# CONFIG_IOSCHED_AS is not set
# CONFIG_IOSCHED_DEADLINE is not set
CONFIG_IOSCHED_CFQ=y
# CONFIG_DEFAULT_AS is not set
# CONFIG_DEFAULT_DEADLINE is not set
CONFIG_DEFAULT_CFQ=y
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="cfq"
CONFIG_PREEMPT_NOTIFIERS=y
#
# Processor type and features
#
CONFIG_TICK_ONESHOT=y
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y
CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
CONFIG_SMP=y
CONFIG_X86_PC=y
# CONFIG_X86_ELAN is not set
# CONFIG_X86_VOYAGER is not set
# CONFIG_X86_NUMAQ is not set
# CONFIG_X86_SUMMIT is not set
# CONFIG_X86_BIGSMP is not set
# CONFIG_X86_VISWS is not set
# CONFIG_X86_GENERICARCH is not set
# CONFIG_X86_ES7000 is not set
# CONFIG_X86_VSMP is not set
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
# CONFIG_M686 is not set
# CONFIG_MPENTIUMII is not set
# CONFIG_MPENTIUMIII is not set
# CONFIG_MPENTIUMM is not set
# CONFIG_MPENTIUM4 is not set
# CONFIG_MK6 is not set
# CONFIG_MK7 is not set
CONFIG_MK8=y
# CONFIG_MCRUSOE is not set
# CONFIG_MEFFICEON is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP2 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MGEODEGX1 is not set
# CONFIG_MGEODE_LX is not set
# CONFIG_MCYRIXIII is not set
# CONFIG_MVIAC3_2 is not set
# CONFIG_MVIAC7 is not set
# CONFIG_MPSC is not set
# CONFIG_MCORE2 is not set
# CONFIG_GENERIC_CPU is not set
CONFIG_X86_L1_CACHE_BYTES=64
CONFIG_X86_INTERNODE_CACHE_BYTES=64
CONFIG_X86_CMPXCHG=y
CONFIG_X86_L1_CACHE_SHIFT=6
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_INTEL_USERCOPY=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_X86_TSC=y
CONFIG_X86_MINIMUM_CPU_FAMILY=64
CONFIG_HPET_TIMER=y
CONFIG_HPET_EMULATE_RTC=y
CONFIG_GART_IOMMU=y
# CONFIG_CALGARY_IOMMU is not set
CONFIG_SWIOTLB=y
CONFIG_NR_CPUS=2
# CONFIG_SCHED_SMT is not set
CONFIG_SCHED_MC=y
# CONFIG_PREEMPT_NONE is not set
CONFIG_PREEMPT_VOLUNTARY=y
# CONFIG_PREEMPT is not set
CONFIG_PREEMPT_BKL=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_X86_IO_APIC=y
CONFIG_X86_MCE=y
# CONFIG_X86_MCE_INTEL is not set
CONFIG_X86_MCE_AMD=y
# CONFIG_MICROCODE is not set
CONFIG_X86_MSR=y
CONFIG_X86_CPUID=y
# CONFIG_NUMA is not set
CONFIG_ARCH_FLATMEM_ENABLE=y
CONFIG_ARCH_SPARSEMEM_ENABLE=y
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
# CONFIG_SPARSEMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
# CONFIG_SPARSEMEM_STATIC is not set
CONFIG_SPARSEMEM_VMEMMAP_ENABLE=y
CONFIG_SPLIT_PTLOCK_CPUS=4
CONFIG_RESOURCES_64BIT=y
CONFIG_ZONE_DMA_FLAG=1
CONFIG_BOUNCE=y
CONFIG_VIRT_TO_BUS=y
CONFIG_MTRR=y
# CONFIG_SECCOMP is not set
# CONFIG_CC_STACKPROTECTOR is not set
# CONFIG_HZ_100 is not set
# CONFIG_HZ_250 is not set
CONFIG_HZ_300=y
# CONFIG_HZ_1000 is not set
CONFIG_HZ=300
# CONFIG_KEXEC is not set
# CONFIG_CRASH_DUMP is not set
CONFIG_PHYSICAL_START=0x200000
# CONFIG_RELOCATABLE is not set
CONFIG_PHYSICAL_ALIGN=0x200000
CONFIG_HOTPLUG_CPU=y
CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
#
# Power management options
#
CONFIG_ARCH_HIBERNATION_HEADER=y
CONFIG_PM=y
# CONFIG_PM_LEGACY is not set
# CONFIG_PM_DEBUG is not set
CONFIG_PM_SLEEP_SMP=y
CONFIG_PM_SLEEP=y
CONFIG_SUSPEND_SMP_POSSIBLE=y
CONFIG_SUSPEND=y
CONFIG_HIBERNATION_SMP_POSSIBLE=y
CONFIG_HIBERNATION=y
CONFIG_PM_STD_PARTITION=""
CONFIG_ACPI=y
CONFIG_ACPI_SLEEP=y
# CONFIG_ACPI_PROCFS is not set
CONFIG_ACPI_PROCFS_POWER=y
CONFIG_ACPI_SYSFS_POWER=y
CONFIG_ACPI_PROC_EVENT=y
CONFIG_ACPI_AC=y
CONFIG_ACPI_BATTERY=y
CONFIG_ACPI_BUTTON=y
CONFIG_ACPI_FAN=y
# CONFIG_ACPI_DOCK is not set
CONFIG_ACPI_PROCESSOR=y
CONFIG_ACPI_HOTPLUG_CPU=y
CONFIG_ACPI_THERMAL=y
# CONFIG_ACPI_ASUS is not set
# CONFIG_ACPI_TOSHIBA is not set
# CONFIG_ACPI_CUSTOM_DSDT is not set
CONFIG_ACPI_BLACKLIST_YEAR=0
# CONFIG_ACPI_DEBUG is not set
CONFIG_ACPI_EC=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_SYSTEM=y
CONFIG_X86_PM_TIMER=y
CONFIG_ACPI_CONTAINER=y
# CONFIG_ACPI_SBS is not set
#
# CPU Frequency scaling
#
CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_TABLE=y
# CONFIG_CPU_FREQ_DEBUG is not set
CONFIG_CPU_FREQ_STAT=y
# CONFIG_CPU_FREQ_STAT_DETAILS is not set
# CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set
# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND=y
# CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE is not set
CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
CONFIG_CPU_FREQ_GOV_POWERSAVE=y
# CONFIG_CPU_FREQ_GOV_USERSPACE is not set
CONFIG_CPU_FREQ_GOV_ONDEMAND=y
# CONFIG_CPU_FREQ_GOV_CONSERVATIVE is not set
#
# CPUFreq processor drivers
#
# CONFIG_X86_ACPI_CPUFREQ is not set
CONFIG_X86_POWERNOW_K8=y
CONFIG_X86_POWERNOW_K8_ACPI=y
# CONFIG_X86_SPEEDSTEP_CENTRINO is not set
# CONFIG_X86_P4_CLOCKMOD is not set
#
# shared options
#
# CONFIG_X86_ACPI_CPUFREQ_PROC_INTF is not set
# CONFIG_X86_SPEEDSTEP_LIB is not set
# CONFIG_CPU_IDLE is not set
#
# Bus options (PCI etc.)
#
CONFIG_PCI=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_MMCONFIG=y
CONFIG_PCI_DOMAINS=y
# CONFIG_DMAR is not set
CONFIG_PCIEPORTBUS=y
CONFIG_PCIEAER=y
CONFIG_ARCH_SUPPORTS_MSI=y
CONFIG_PCI_MSI=y
CONFIG_PCI_LEGACY=y
CONFIG_HT_IRQ=y
CONFIG_ISA_DMA_API=y
CONFIG_K8_NB=y
# CONFIG_PCCARD is not set
# CONFIG_HOTPLUG_PCI is not set
#
# Executable file formats / Emulations
#
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_MISC=m
CONFIG_IA32_EMULATION=y
CONFIG_IA32_AOUT=m
CONFIG_COMPAT=y
CONFIG_COMPAT_FOR_U64_ALIGNMENT=y
CONFIG_SYSVIPC_COMPAT=y
#
# Networking
#
CONFIG_NET=y
#
# Networking options
#
CONFIG_PACKET=m
CONFIG_PACKET_MMAP=y
CONFIG_UNIX=y
# CONFIG_NET_KEY is not set
CONFIG_INET=y
# CONFIG_IP_MULTICAST is not set
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_IP_FIB_HASH=y
# CONFIG_IP_PNP is not set
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
# CONFIG_ARPD is not set
# CONFIG_SYN_COOKIES is not set
# CONFIG_INET_AH is not set
# CONFIG_INET_ESP is not set
# CONFIG_INET_IPCOMP is not set
# CONFIG_INET_XFRM_TUNNEL is not set
# CONFIG_INET_TUNNEL is not set
# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
# CONFIG_INET_XFRM_MODE_TUNNEL is not set
# CONFIG_INET_XFRM_MODE_BEET is not set
# CONFIG_INET_LRO is not set
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_CUBIC=y
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TCP_MD5SIG is not set
# CONFIG_IPV6 is not set
# CONFIG_INET6_XFRM_TUNNEL is not set
# CONFIG_INET6_TUNNEL is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
CONFIG_VLAN_8021Q=m
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_NET_SCHED is not set
#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
CONFIG_BT=m
CONFIG_BT_L2CAP=m
CONFIG_BT_SCO=m
CONFIG_BT_RFCOMM=m
CONFIG_BT_RFCOMM_TTY=y
CONFIG_BT_BNEP=m
CONFIG_BT_BNEP_MC_FILTER=y
CONFIG_BT_BNEP_PROTO_FILTER=y
CONFIG_BT_HIDP=m
#
# Bluetooth device drivers
#
# CONFIG_BT_HCIUSB is not set
# CONFIG_BT_HCIBTUSB is not set
CONFIG_BT_HCIUART=m
CONFIG_BT_HCIUART_H4=y
CONFIG_BT_HCIUART_BCSP=y
CONFIG_BT_HCIUART_LL=y
# CONFIG_BT_HCIBCM203X is not set
# CONFIG_BT_HCIBPA10X is not set
# CONFIG_BT_HCIBFUSB is not set
CONFIG_BT_HCIVHCI=m
# CONFIG_AF_RXRPC is not set
#
# Wireless
#
# CONFIG_CFG80211 is not set
# CONFIG_WIRELESS_EXT is not set
# CONFIG_MAC80211 is not set
# CONFIG_IEEE80211 is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
#
# Device Drivers
#
#
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
# CONFIG_STANDALONE is not set
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=m
# CONFIG_SYS_HYPERVISOR is not set
# CONFIG_CONNECTOR is not set
# CONFIG_MTD is not set
# CONFIG_PARPORT is not set
CONFIG_PNP=y
# CONFIG_PNP_DEBUG is not set
#
# Protocols
#
CONFIG_PNPACPI=y
CONFIG_BLK_DEV=y
# CONFIG_BLK_DEV_FD is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=m
# CONFIG_BLK_DEV_CRYPTOLOOP is not set
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_SX8 is not set
# CONFIG_BLK_DEV_UB is not set
# CONFIG_BLK_DEV_RAM is not set
CONFIG_CDROM_PKTCDVD=m
CONFIG_CDROM_PKTCDVD_BUFFERS=16
# CONFIG_CDROM_PKTCDVD_WCACHE is not set
# CONFIG_ATA_OVER_ETH is not set
# CONFIG_MISC_DEVICES is not set
# CONFIG_IDE is not set
#
# SCSI device support
#
# CONFIG_RAID_ATTRS is not set
CONFIG_SCSI=y
CONFIG_SCSI_DMA=y
CONFIG_SCSI_TGT=m
# CONFIG_SCSI_NETLINK is not set
CONFIG_SCSI_PROC_FS=y
#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
CONFIG_CHR_DEV_ST=m
# CONFIG_CHR_DEV_OSST is not set
CONFIG_BLK_DEV_SR=m
CONFIG_BLK_DEV_SR_VENDOR=y
CONFIG_CHR_DEV_SG=m
CONFIG_CHR_DEV_SCH=m
#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
CONFIG_SCSI_MULTI_LUN=y
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set
# CONFIG_SCSI_SCAN_ASYNC is not set
CONFIG_SCSI_WAIT_SCAN=m
#
# SCSI Transports
#
CONFIG_SCSI_SPI_ATTRS=y
# CONFIG_SCSI_FC_ATTRS is not set
# CONFIG_SCSI_ISCSI_ATTRS is not set
# CONFIG_SCSI_SAS_ATTRS is not set
# CONFIG_SCSI_SAS_LIBSAS is not set
# CONFIG_SCSI_SRP_ATTRS is not set
CONFIG_SCSI_LOWLEVEL=y
# CONFIG_ISCSI_TCP is not set
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_3W_9XXX is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AACRAID is not set
CONFIG_SCSI_AIC7XXX=m
CONFIG_AIC7XXX_CMDS_PER_DEVICE=32
CONFIG_AIC7XXX_RESET_DELAY_MS=5000
CONFIG_AIC7XXX_DEBUG_ENABLE=y
CONFIG_AIC7XXX_DEBUG_MASK=0
CONFIG_AIC7XXX_REG_PRETTY_PRINT=y
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_AIC94XX is not set
# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_SCSI_ARCMSR is not set
# CONFIG_MEGARAID_NEWGEN is not set
# CONFIG_MEGARAID_LEGACY is not set
# CONFIG_MEGARAID_SAS is not set
# CONFIG_SCSI_HPTIOP is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_STEX is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_IPR is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
# CONFIG_SCSI_QLA_FC is not set
# CONFIG_SCSI_QLA_ISCSI is not set
# CONFIG_SCSI_LPFC is not set
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_DEBUG is not set
# CONFIG_SCSI_SRP is not set
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
CONFIG_ATA_ACPI=y
CONFIG_SATA_AHCI=y
# CONFIG_SATA_SVW is not set
# CONFIG_ATA_PIIX is not set
# CONFIG_SATA_MV is not set
# CONFIG_SATA_NV is not set
# CONFIG_PDC_ADMA is not set
# CONFIG_SATA_QSTOR is not set
# CONFIG_SATA_PROMISE is not set
# CONFIG_SATA_SX4 is not set
# CONFIG_SATA_SIL is not set
# CONFIG_SATA_SIL24 is not set
# CONFIG_SATA_SIS is not set
# CONFIG_SATA_ULI is not set
# CONFIG_SATA_VIA is not set
# CONFIG_SATA_VITESSE is not set
# CONFIG_SATA_INIC162X is not set
# CONFIG_PATA_ACPI is not set
# CONFIG_PATA_ALI is not set
# CONFIG_PATA_AMD is not set
# CONFIG_PATA_ARTOP is not set
# CONFIG_PATA_ATIIXP is not set
# CONFIG_PATA_CMD640_PCI is not set
# CONFIG_PATA_CMD64X is not set
# CONFIG_PATA_CS5520 is not set
# CONFIG_PATA_CS5530 is not set
# CONFIG_PATA_CYPRESS is not set
# CONFIG_PATA_EFAR is not set
# CONFIG_ATA_GENERIC is not set
# CONFIG_PATA_HPT366 is not set
# CONFIG_PATA_HPT37X is not set
# CONFIG_PATA_HPT3X2N is not set
# CONFIG_PATA_HPT3X3 is not set
# CONFIG_PATA_IT821X is not set
# CONFIG_PATA_IT8213 is not set
# CONFIG_PATA_JMICRON is not set
# CONFIG_PATA_TRIFLEX is not set
# CONFIG_PATA_MARVELL is not set
# CONFIG_PATA_MPIIX is not set
# CONFIG_PATA_OLDPIIX is not set
# CONFIG_PATA_NETCELL is not set
# CONFIG_PATA_NS87410 is not set
# CONFIG_PATA_NS87415 is not set
# CONFIG_PATA_OPTI is not set
# CONFIG_PATA_OPTIDMA is not set
# CONFIG_PATA_PDC_OLD is not set
# CONFIG_PATA_RADISYS is not set
# CONFIG_PATA_RZ1000 is not set
# CONFIG_PATA_SC1200 is not set
# CONFIG_PATA_SERVERWORKS is not set
# CONFIG_PATA_PDC2027X is not set
# CONFIG_PATA_SIL680 is not set
# CONFIG_PATA_SIS is not set
# CONFIG_PATA_VIA is not set
# CONFIG_PATA_WINBOND is not set
# CONFIG_PATA_PLATFORM is not set
# CONFIG_MD is not set
# CONFIG_FUSION is not set
#
# IEEE 1394 (FireWire) support
#
CONFIG_FIREWIRE=m
CONFIG_FIREWIRE_OHCI=m
CONFIG_FIREWIRE_SBP2=m
# CONFIG_IEEE1394 is not set
# CONFIG_I2O is not set
# CONFIG_MACINTOSH_DRIVERS is not set
CONFIG_NETDEVICES=y
# CONFIG_NETDEVICES_MULTIQUEUE is not set
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_MACVLAN is not set
# CONFIG_EQUALIZER is not set
CONFIG_TUN=m
# CONFIG_VETH is not set
# CONFIG_NET_SB1000 is not set
# CONFIG_ARCNET is not set
# CONFIG_NET_ETHERNET is not set
CONFIG_NETDEV_1000=y
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_E1000E is not set
# CONFIG_IP1000 is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
CONFIG_R8169=m
# CONFIG_R8169_NAPI is not set
CONFIG_R8169_VLAN=y
# CONFIG_SIS190 is not set
# CONFIG_SKGE is not set
# CONFIG_SKY2 is not set
# CONFIG_SK98LIN is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
# CONFIG_QLA3XXX is not set
# CONFIG_ATL1 is not set
# CONFIG_NETDEV_10000 is not set
# CONFIG_TR is not set
#
# Wireless LAN
#
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
#
# USB Network Adapters
#
# CONFIG_USB_CATC is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
# CONFIG_USB_USBNET is not set
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
# CONFIG_NET_FC is not set
# CONFIG_SHAPER is not set
# CONFIG_NETCONSOLE is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
# CONFIG_ISDN is not set
# CONFIG_PHONE is not set
#
# Input device support
#
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
# CONFIG_INPUT_POLLDEV is not set
#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=m
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1680
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=1050
# CONFIG_INPUT_JOYDEV is not set
CONFIG_INPUT_EVDEV=y
# CONFIG_INPUT_EVBUG is not set
#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_LKKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TABLET is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_INPUT_MISC is not set
#
# Hardware I/O ports
#
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
# CONFIG_SERIO_SERPORT is not set
# CONFIG_SERIO_CT82C710 is not set
# CONFIG_SERIO_PCIPS2 is not set
CONFIG_SERIO_LIBPS2=y
# CONFIG_SERIO_RAW is not set
# CONFIG_GAMEPORT is not set
#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_VT_HW_CONSOLE_BINDING is not set
# CONFIG_SERIAL_NONSTANDARD is not set
#
# Serial drivers
#
# CONFIG_SERIAL_8250 is not set
CONFIG_FIX_EARLYCON_MEM=y
#
# Non-8250 serial port support
#
# CONFIG_SERIAL_JSM is not set
CONFIG_UNIX98_PTYS=y
# CONFIG_LEGACY_PTYS is not set
# CONFIG_IPMI_HANDLER is not set
# CONFIG_HW_RANDOM is not set
CONFIG_NVRAM=m
CONFIG_RTC=y
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_MWAVE is not set
# CONFIG_PC8736x_GPIO is not set
# CONFIG_RAW_DRIVER is not set
CONFIG_HPET=y
# CONFIG_HPET_RTC_IRQ is not set
CONFIG_HPET_MMAP=y
CONFIG_HANGCHECK_TIMER=m
# CONFIG_TCG_TPM is not set
# CONFIG_TELCLOCK is not set
CONFIG_DEVPORT=y
CONFIG_I2C=m
CONFIG_I2C_BOARDINFO=y
CONFIG_I2C_CHARDEV=m
#
# I2C Algorithms
#
CONFIG_I2C_ALGOBIT=m
# CONFIG_I2C_ALGOPCF is not set
# CONFIG_I2C_ALGOPCA is not set
#
# I2C Hardware Bus support
#
# CONFIG_I2C_ALI1535 is not set
# CONFIG_I2C_ALI1563 is not set
# CONFIG_I2C_ALI15X3 is not set
CONFIG_I2C_AMD756=m
# CONFIG_I2C_AMD756_S4882 is not set
# CONFIG_I2C_AMD8111 is not set
# CONFIG_I2C_I801 is not set
# CONFIG_I2C_I810 is not set
# CONFIG_I2C_PIIX4 is not set
CONFIG_I2C_NFORCE2=m
# CONFIG_I2C_OCORES is not set
# CONFIG_I2C_PARPORT_LIGHT is not set
# CONFIG_I2C_PROSAVAGE is not set
# CONFIG_I2C_SAVAGE4 is not set
# CONFIG_I2C_SIMTEC is not set
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
# CONFIG_I2C_SIS96X is not set
# CONFIG_I2C_TAOS_EVM is not set
# CONFIG_I2C_STUB is not set
# CONFIG_I2C_TINY_USB is not set
# CONFIG_I2C_VIA is not set
# CONFIG_I2C_VIAPRO is not set
# CONFIG_I2C_VOODOO3 is not set
#
# Miscellaneous I2C Chip support
#
# CONFIG_SENSORS_DS1337 is not set
# CONFIG_SENSORS_DS1374 is not set
# CONFIG_DS1682 is not set
CONFIG_SENSORS_EEPROM=m
# CONFIG_SENSORS_PCF8574 is not set
# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_PCF8591 is not set
# CONFIG_SENSORS_MAX6875 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set
#
# SPI support
#
# CONFIG_SPI is not set
# CONFIG_SPI_MASTER is not set
# CONFIG_W1 is not set
CONFIG_POWER_SUPPLY=y
# CONFIG_POWER_SUPPLY_DEBUG is not set
# CONFIG_PDA_POWER is not set
# CONFIG_BATTERY_DS2760 is not set
CONFIG_HWMON=m
CONFIG_HWMON_VID=m
# CONFIG_SENSORS_ABITUGURU is not set
# CONFIG_SENSORS_ABITUGURU3 is not set
# CONFIG_SENSORS_AD7418 is not set
# CONFIG_SENSORS_ADM1021 is not set
# CONFIG_SENSORS_ADM1025 is not set
# CONFIG_SENSORS_ADM1026 is not set
# CONFIG_SENSORS_ADM1029 is not set
# CONFIG_SENSORS_ADM1031 is not set
# CONFIG_SENSORS_ADM9240 is not set
# CONFIG_SENSORS_ADT7470 is not set
CONFIG_SENSORS_K8TEMP=m
# CONFIG_SENSORS_ASB100 is not set
# CONFIG_SENSORS_ATXP1 is not set
# CONFIG_SENSORS_DS1621 is not set
# CONFIG_SENSORS_I5K_AMB is not set
# CONFIG_SENSORS_F71805F is not set
# CONFIG_SENSORS_F71882FG is not set
# CONFIG_SENSORS_F75375S is not set
# CONFIG_SENSORS_FSCHER is not set
# CONFIG_SENSORS_FSCPOS is not set
# CONFIG_SENSORS_FSCHMD is not set
# CONFIG_SENSORS_GL518SM is not set
# CONFIG_SENSORS_GL520SM is not set
# CONFIG_SENSORS_CORETEMP is not set
# CONFIG_SENSORS_IT87 is not set
# CONFIG_SENSORS_LM63 is not set
# CONFIG_SENSORS_LM75 is not set
# CONFIG_SENSORS_LM77 is not set
# CONFIG_SENSORS_LM78 is not set
# CONFIG_SENSORS_LM80 is not set
# CONFIG_SENSORS_LM83 is not set
# CONFIG_SENSORS_LM85 is not set
# CONFIG_SENSORS_LM87 is not set
# CONFIG_SENSORS_LM90 is not set
# CONFIG_SENSORS_LM92 is not set
# CONFIG_SENSORS_LM93 is not set
# CONFIG_SENSORS_MAX1619 is not set
# CONFIG_SENSORS_MAX6650 is not set
# CONFIG_SENSORS_PC87360 is not set
# CONFIG_SENSORS_PC87427 is not set
# CONFIG_SENSORS_SIS5595 is not set
# CONFIG_SENSORS_DME1737 is not set
# CONFIG_SENSORS_SMSC47M1 is not set
# CONFIG_SENSORS_SMSC47M192 is not set
# CONFIG_SENSORS_SMSC47B397 is not set
# CONFIG_SENSORS_THMC50 is not set
# CONFIG_SENSORS_VIA686A is not set
# CONFIG_SENSORS_VT1211 is not set
# CONFIG_SENSORS_VT8231 is not set
# CONFIG_SENSORS_W83781D is not set
# CONFIG_SENSORS_W83791D is not set
# CONFIG_SENSORS_W83792D is not set
# CONFIG_SENSORS_W83793 is not set
# CONFIG_SENSORS_W83L785TS is not set
# CONFIG_SENSORS_W83627HF is not set
CONFIG_SENSORS_W83627EHF=m
# CONFIG_SENSORS_HDAPS is not set
# CONFIG_SENSORS_APPLESMC is not set
# CONFIG_HWMON_DEBUG_CHIP is not set
# CONFIG_WATCHDOG is not set
#
# Sonics Silicon Backplane
#
CONFIG_SSB_POSSIBLE=y
# CONFIG_SSB is not set
#
# Multifunction device drivers
#
# CONFIG_MFD_SM501 is not set
#
# Multimedia devices
#
CONFIG_VIDEO_DEV=m
CONFIG_VIDEO_V4L1=y
CONFIG_VIDEO_V4L1_COMPAT=y
CONFIG_VIDEO_V4L2=y
CONFIG_VIDEO_CAPTURE_DRIVERS=y
# CONFIG_VIDEO_ADV_DEBUG is not set
CONFIG_VIDEO_HELPER_CHIPS_AUTO=y
CONFIG_VIDEO_SAA711X=m
CONFIG_VIDEO_TVP5150=m
# CONFIG_VIDEO_VIVI is not set
# CONFIG_VIDEO_BT848 is not set
# CONFIG_VIDEO_CPIA is not set
# CONFIG_VIDEO_CPIA2 is not set
# CONFIG_VIDEO_SAA5246A is not set
# CONFIG_VIDEO_SAA5249 is not set
# CONFIG_TUNER_3036 is not set
# CONFIG_VIDEO_STRADIS is not set
# CONFIG_VIDEO_ZORAN is not set
# CONFIG_VIDEO_SAA7134 is not set
# CONFIG_VIDEO_MXB is not set
# CONFIG_VIDEO_DPC is not set
# CONFIG_VIDEO_HEXIUM_ORION is not set
# CONFIG_VIDEO_HEXIUM_GEMINI is not set
# CONFIG_VIDEO_CX88 is not set
# CONFIG_VIDEO_CX23885 is not set
# CONFIG_VIDEO_IVTV is not set
# CONFIG_VIDEO_CAFE_CCIC is not set
CONFIG_V4L_USB_DRIVERS=y
# CONFIG_VIDEO_PVRUSB2 is not set
CONFIG_VIDEO_EM28XX=m
# CONFIG_VIDEO_USBVISION is not set
# CONFIG_USB_VICAM is not set
# CONFIG_USB_IBMCAM is not set
# CONFIG_USB_KONICAWC is not set
# CONFIG_USB_QUICKCAM_MESSENGER is not set
# CONFIG_USB_ET61X251 is not set
# CONFIG_VIDEO_OVCAMCHIP is not set
# CONFIG_USB_W9968CF is not set
# CONFIG_USB_OV511 is not set
# CONFIG_USB_SE401 is not set
# CONFIG_USB_SN9C102 is not set
# CONFIG_USB_STV680 is not set
# CONFIG_USB_ZC0301 is not set
# CONFIG_USB_PWC is not set
# CONFIG_USB_ZR364XX is not set
# CONFIG_RADIO_ADAPTERS is not set
CONFIG_DVB_CORE=m
CONFIG_DVB_CORE_ATTACH=y
CONFIG_DVB_CAPTURE_DRIVERS=y
#
# Supported SAA7146 based PCI Adapters
#
# CONFIG_DVB_AV7110 is not set
# CONFIG_DVB_BUDGET is not set
# CONFIG_DVB_BUDGET_CI is not set
# CONFIG_DVB_BUDGET_AV is not set
#
# Supported USB Adapters
#
# CONFIG_DVB_USB is not set
# CONFIG_DVB_TTUSB_BUDGET is not set
# CONFIG_DVB_TTUSB_DEC is not set
# CONFIG_DVB_CINERGYT2 is not set
#
# Supported FlexCopII (B2C2) Adapters
#
# CONFIG_DVB_B2C2_FLEXCOP is not set
#
# Supported BT878 Adapters
#
#
# Supported Pluto2 Adapters
#
# CONFIG_DVB_PLUTO2 is not set
#
# Supported DVB Frontends
#
#
# Customise DVB Frontends
#
# CONFIG_DVB_FE_CUSTOMISE is not set
#
# DVB-S (satellite) frontends
#
# CONFIG_DVB_STV0299 is not set
# CONFIG_DVB_CX24110 is not set
# CONFIG_DVB_CX24123 is not set
# CONFIG_DVB_TDA8083 is not set
# CONFIG_DVB_MT312 is not set
# CONFIG_DVB_VES1X93 is not set
# CONFIG_DVB_S5H1420 is not set
# CONFIG_DVB_TDA10086 is not set
#
# DVB-T (terrestrial) frontends
#
# CONFIG_DVB_SP8870 is not set
# CONFIG_DVB_SP887X is not set
# CONFIG_DVB_CX22700 is not set
# CONFIG_DVB_CX22702 is not set
# CONFIG_DVB_L64781 is not set
# CONFIG_DVB_TDA1004X is not set
# CONFIG_DVB_NXT6000 is not set
CONFIG_DVB_MT352=m
CONFIG_DVB_ZL10353=m
# CONFIG_DVB_DIB3000MB is not set
# CONFIG_DVB_DIB3000MC is not set
# CONFIG_DVB_DIB7000M is not set
# CONFIG_DVB_DIB7000P is not set
#
# DVB-C (cable) frontends
#
# CONFIG_DVB_VES1820 is not set
# CONFIG_DVB_TDA10021 is not set
# CONFIG_DVB_TDA10023 is not set
# CONFIG_DVB_STV0297 is not set
#
# ATSC (North American/Korean Terrestrial/Cable DTV) frontends
#
# CONFIG_DVB_NXT200X is not set
# CONFIG_DVB_OR51211 is not set
# CONFIG_DVB_OR51132 is not set
# CONFIG_DVB_BCM3510 is not set
# CONFIG_DVB_LGDT330X is not set
# CONFIG_DVB_S5H1409 is not set
#
# Tuners/PLL support
#
# CONFIG_DVB_PLL is not set
# CONFIG_DVB_TDA826X is not set
# CONFIG_DVB_TDA827X is not set
# CONFIG_DVB_TUNER_QT1010 is not set
# CONFIG_DVB_TUNER_MT2060 is not set
# CONFIG_DVB_TUNER_MT2266 is not set
# CONFIG_DVB_TUNER_MT2131 is not set
# CONFIG_DVB_TUNER_DIB0070 is not set
#
# Miscellaneous devices
#
# CONFIG_DVB_LNBP21 is not set
# CONFIG_DVB_ISL6421 is not set
# CONFIG_DVB_TUA6100 is not set
CONFIG_VIDEO_TUNER=m
CONFIG_VIDEO_TUNER_CUSTOMIZE=y
CONFIG_TUNER_MT20XX=m
CONFIG_TUNER_TDA8290=m
CONFIG_TUNER_TEA5761=m
CONFIG_TUNER_TEA5767=m
CONFIG_TUNER_SIMPLE=m
CONFIG_VIDEO_IR_I2C=m
CONFIG_VIDEO_IR=m
CONFIG_VIDEO_TVEEPROM=m
# CONFIG_DAB is not set
#
# Graphics support
#
CONFIG_AGP=y
CONFIG_AGP_AMD64=y
# CONFIG_AGP_INTEL is not set
# CONFIG_AGP_SIS is not set
# CONFIG_AGP_VIA is not set
# CONFIG_DRM is not set
# CONFIG_VGASTATE is not set
# CONFIG_VIDEO_OUTPUT_CONTROL is not set
# CONFIG_FB is not set
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
# Display device support
#
# CONFIG_DISPLAY_SUPPORT is not set
#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
# CONFIG_VGACON_SOFT_SCROLLBACK is not set
CONFIG_VIDEO_SELECT=y
CONFIG_DUMMY_CONSOLE=y
#
# Sound
#
CONFIG_SOUND=m
#
# Advanced Linux Sound Architecture
#
CONFIG_SND=m
CONFIG_SND_TIMER=m
CONFIG_SND_PCM=m
CONFIG_SND_HWDEP=m
CONFIG_SND_RAWMIDI=m
CONFIG_SND_SEQUENCER=m
# CONFIG_SND_SEQ_DUMMY is not set
CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=m
CONFIG_SND_PCM_OSS=m
# CONFIG_SND_PCM_OSS_PLUGINS is not set
CONFIG_SND_SEQUENCER_OSS=y
CONFIG_SND_RTCTIMER=m
CONFIG_SND_SEQ_RTCTIMER_DEFAULT=y
# CONFIG_SND_DYNAMIC_MINORS is not set
# CONFIG_SND_SUPPORT_OLD_API is not set
CONFIG_SND_VERBOSE_PROCFS=y
# CONFIG_SND_VERBOSE_PRINTK is not set
# CONFIG_SND_DEBUG is not set
#
# Generic devices
#
CONFIG_SND_MPU401_UART=m
CONFIG_SND_AC97_CODEC=m
CONFIG_SND_DUMMY=m
CONFIG_SND_VIRMIDI=m
# CONFIG_SND_MTPAV is not set
# CONFIG_SND_SERIAL_U16550 is not set
CONFIG_SND_MPU401=m
#
# PCI devices
#
# CONFIG_SND_AD1889 is not set
# CONFIG_SND_ALS300 is not set
# CONFIG_SND_ALS4000 is not set
# CONFIG_SND_ALI5451 is not set
# CONFIG_SND_ATIIXP is not set
# CONFIG_SND_ATIIXP_MODEM is not set
# CONFIG_SND_AU8810 is not set
# CONFIG_SND_AU8820 is not set
# CONFIG_SND_AU8830 is not set
# CONFIG_SND_AZT3328 is not set
# CONFIG_SND_BT87X is not set
# CONFIG_SND_CA0106 is not set
# CONFIG_SND_CMIPCI is not set
# CONFIG_SND_CS4281 is not set
# CONFIG_SND_CS46XX is not set
# CONFIG_SND_CS5530 is not set
# CONFIG_SND_DARLA20 is not set
# CONFIG_SND_GINA20 is not set
# CONFIG_SND_LAYLA20 is not set
# CONFIG_SND_DARLA24 is not set
# CONFIG_SND_GINA24 is not set
# CONFIG_SND_LAYLA24 is not set
# CONFIG_SND_MONA is not set
# CONFIG_SND_MIA is not set
# CONFIG_SND_ECHO3G is not set
# CONFIG_SND_INDIGO is not set
# CONFIG_SND_INDIGOIO is not set
# CONFIG_SND_INDIGODJ is not set
CONFIG_SND_EMU10K1=m
# CONFIG_SND_EMU10K1X is not set
# CONFIG_SND_ENS1370 is not set
# CONFIG_SND_ENS1371 is not set
# CONFIG_SND_ES1938 is not set
# CONFIG_SND_ES1968 is not set
# CONFIG_SND_FM801 is not set
# CONFIG_SND_HDA_INTEL is not set
# CONFIG_SND_HDSP is not set
# CONFIG_SND_HDSPM is not set
# CONFIG_SND_ICE1712 is not set
# CONFIG_SND_ICE1724 is not set
# CONFIG_SND_INTEL8X0 is not set
# CONFIG_SND_INTEL8X0M is not set
# CONFIG_SND_KORG1212 is not set
# CONFIG_SND_MAESTRO3 is not set
# CONFIG_SND_MIXART is not set
# CONFIG_SND_NM256 is not set
# CONFIG_SND_PCXHR is not set
# CONFIG_SND_RIPTIDE is not set
# CONFIG_SND_RME32 is not set
# CONFIG_SND_RME96 is not set
# CONFIG_SND_RME9652 is not set
# CONFIG_SND_SONICVIBES is not set
# CONFIG_SND_TRIDENT is not set
# CONFIG_SND_VIA82XX is not set
# CONFIG_SND_VIA82XX_MODEM is not set
# CONFIG_SND_VX222 is not set
# CONFIG_SND_YMFPCI is not set
CONFIG_SND_AC97_POWER_SAVE=y
CONFIG_SND_AC97_POWER_SAVE_DEFAULT=0
#
# USB devices
#
CONFIG_SND_USB_AUDIO=m
# CONFIG_SND_USB_USX2Y is not set
# CONFIG_SND_USB_CAIAQ is not set
#
# System on Chip audio support
#
# CONFIG_SND_SOC is not set
#
# SoC Audio support for SuperH
#
#
# Open Sound System
#
# CONFIG_SOUND_PRIME is not set
CONFIG_AC97_BUS=m
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
# CONFIG_HID_DEBUG is not set
# CONFIG_HIDRAW is not set
#
# USB Input Devices
#
CONFIG_USB_HID=y
# CONFIG_USB_HIDINPUT_POWERBOOK is not set
# CONFIG_HID_FF is not set
# CONFIG_USB_HIDDEV is not set
CONFIG_USB_SUPPORT=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB_ARCH_HAS_EHCI=y
CONFIG_USB=y
# CONFIG_USB_DEBUG is not set
#
# Miscellaneous USB options
#
# CONFIG_USB_DEVICEFS is not set
# CONFIG_USB_DEVICE_CLASS is not set
# CONFIG_USB_DYNAMIC_MINORS is not set
CONFIG_USB_SUSPEND=y
# CONFIG_USB_PERSIST is not set
# CONFIG_USB_OTG is not set
#
# USB Host Controller Drivers
#
CONFIG_USB_EHCI_HCD=y
# CONFIG_USB_EHCI_SPLIT_ISO is not set
# CONFIG_USB_EHCI_ROOT_HUB_TT is not set
# CONFIG_USB_EHCI_TT_NEWSCHED is not set
# CONFIG_USB_ISP116X_HCD is not set
CONFIG_USB_OHCI_HCD=m
# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
# CONFIG_USB_UHCI_HCD is not set
# CONFIG_USB_SL811_HCD is not set
# CONFIG_USB_R8A66597_HCD is not set
#
# USB Device Class drivers
#
CONFIG_USB_ACM=m
CONFIG_USB_PRINTER=m
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#
#
# may also be needed; see USB_STORAGE Help for more information
#
CONFIG_USB_STORAGE=m
# CONFIG_USB_STORAGE_DEBUG is not set
# CONFIG_USB_STORAGE_DATAFAB is not set
# CONFIG_USB_STORAGE_FREECOM is not set
# CONFIG_USB_STORAGE_ISD200 is not set
# CONFIG_USB_STORAGE_DPCM is not set
# CONFIG_USB_STORAGE_USBAT is not set
# CONFIG_USB_STORAGE_SDDR09 is not set
# CONFIG_USB_STORAGE_SDDR55 is not set
# CONFIG_USB_STORAGE_JUMPSHOT is not set
# CONFIG_USB_STORAGE_ALAUDA is not set
# CONFIG_USB_STORAGE_KARMA is not set
# CONFIG_USB_LIBUSUAL is not set
#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set
# CONFIG_USB_MON is not set
#
# USB port drivers
#
#
# USB Serial Converter support
#
# CONFIG_USB_SERIAL is not set
#
# USB Miscellaneous drivers
#
# CONFIG_USB_EMI62 is not set
# CONFIG_USB_EMI26 is not set
# CONFIG_USB_ADUTUX is not set
# CONFIG_USB_AUERSWALD is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
# CONFIG_USB_BERRY_CHARGE is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYPRESS_CY7C63 is not set
# CONFIG_USB_CYTHERM is not set
# CONFIG_USB_PHIDGET is not set
# CONFIG_USB_IDMOUSE is not set
# CONFIG_USB_FTDI_ELAN is not set
# CONFIG_USB_APPLEDISPLAY is not set
# CONFIG_USB_SISUSBVGA is not set
# CONFIG_USB_LD is not set
# CONFIG_USB_TRANCEVIBRATOR is not set
# CONFIG_USB_IOWARRIOR is not set
#
# USB DSL modem support
#
#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
# CONFIG_MMC is not set
# CONFIG_NEW_LEDS is not set
# CONFIG_INFINIBAND is not set
# CONFIG_EDAC is not set
# CONFIG_RTC_CLASS is not set
# CONFIG_DMADEVICES is not set
CONFIG_VIRTUALIZATION=y
CONFIG_KVM=m
# CONFIG_KVM_INTEL is not set
CONFIG_KVM_AMD=m
#
# Userspace I/O
#
# CONFIG_UIO is not set
#
# Firmware Drivers
#
# CONFIG_EDD is not set
# CONFIG_DELL_RBU is not set
# CONFIG_DCDBAS is not set
CONFIG_DMIID=y
#
# File systems
#
CONFIG_EXT2_FS=y
# CONFIG_EXT2_FS_XATTR is not set
# CONFIG_EXT2_FS_XIP is not set
# CONFIG_EXT3_FS is not set
# CONFIG_EXT4DEV_FS is not set
CONFIG_REISER4_FS=y
# CONFIG_REISER4_DEBUG is not set
CONFIG_REISERFS_FS=y
# CONFIG_REISERFS_CHECK is not set
# CONFIG_REISERFS_PROC_INFO is not set
# CONFIG_REISERFS_FS_XATTR is not set
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
# CONFIG_QUOTA is not set
CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
# CONFIG_FUSE_FS is not set
#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=m
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_UDF_FS=m
CONFIG_UDF_NLS=y
#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=m
CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=m
CONFIG_FAT_DEFAULT_CODEPAGE=850
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-15"
# CONFIG_NTFS_FS is not set
#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
# CONFIG_PROC_KCORE is not set
CONFIG_PROC_SYSCTL=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_HUGETLBFS is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_CONFIGFS_FS=m
#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_HFSPLUS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
# CONFIG_NETWORK_FILESYSTEMS is not set
#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y
CONFIG_NLS=m
CONFIG_NLS_DEFAULT="iso8859-15"
# CONFIG_NLS_CODEPAGE_437 is not set
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
CONFIG_NLS_CODEPAGE_850=m
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_CODEPAGE_1250 is not set
# CONFIG_NLS_CODEPAGE_1251 is not set
CONFIG_NLS_ASCII=m
CONFIG_NLS_ISO8859_1=m
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_13 is not set
# CONFIG_NLS_ISO8859_14 is not set
CONFIG_NLS_ISO8859_15=m
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
CONFIG_NLS_UTF8=m
# CONFIG_DLM is not set
# CONFIG_INSTRUMENTATION is not set
#
# Kernel hacking
#
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
CONFIG_PRINTK_TIME=y
# CONFIG_ENABLE_WARN_DEPRECATED is not set
# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_MAGIC_SYSRQ=y
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_KERNEL is not set
# CONFIG_DEBUG_BUGVERBOSE is not set
# CONFIG_SAMPLES is not set
CONFIG_EARLY_PRINTK=y
#
# Security options
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
# CONFIG_SECURITY_FILE_CAPABILITIES is not set
CONFIG_CRYPTO=y
# CONFIG_CRYPTO_MANAGER is not set
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
# CONFIG_CRYPTO_NULL is not set
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_SHA1 is not set
# CONFIG_CRYPTO_SHA256 is not set
# CONFIG_CRYPTO_SHA512 is not set
# CONFIG_CRYPTO_WP512 is not set
# CONFIG_CRYPTO_TGR192 is not set
# CONFIG_CRYPTO_GF128MUL is not set
# CONFIG_CRYPTO_ECB is not set
# CONFIG_CRYPTO_CBC is not set
# CONFIG_CRYPTO_PCBC is not set
# CONFIG_CRYPTO_LRW is not set
# CONFIG_CRYPTO_XTS is not set
# CONFIG_CRYPTO_CRYPTD is not set
# CONFIG_CRYPTO_DES is not set
# CONFIG_CRYPTO_FCRYPT is not set
# CONFIG_CRYPTO_BLOWFISH is not set
# CONFIG_CRYPTO_TWOFISH is not set
# CONFIG_CRYPTO_TWOFISH_X86_64 is not set
# CONFIG_CRYPTO_SERPENT is not set
# CONFIG_CRYPTO_AES is not set
# CONFIG_CRYPTO_AES_X86_64 is not set
# CONFIG_CRYPTO_CAST5 is not set
# CONFIG_CRYPTO_CAST6 is not set
# CONFIG_CRYPTO_TEA is not set
# CONFIG_CRYPTO_ARC4 is not set
# CONFIG_CRYPTO_KHAZAD is not set
# CONFIG_CRYPTO_ANUBIS is not set
# CONFIG_CRYPTO_SEED is not set
# CONFIG_CRYPTO_DEFLATE is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
# CONFIG_CRYPTO_CRC32C is not set
# CONFIG_CRYPTO_CAMELLIA is not set
# CONFIG_CRYPTO_TEST is not set
# CONFIG_CRYPTO_AUTHENC is not set
# CONFIG_CRYPTO_HW is not set
#
# Library routines
#
CONFIG_BITREVERSE=y
# CONFIG_CRC_CCITT is not set
CONFIG_CRC16=m
CONFIG_CRC_ITU_T=m
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
CONFIG_LIBCRC32C=m
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
CONFIG_LZO_COMPRESS=y
CONFIG_LZO_DECOMPRESS=y
CONFIG_PLIST=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
