Re: Hauppauge HVR-1700 Support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Torben Viets wrote:
> Steven Toth wrote:
>> Torben Viets wrote:
>>> Hello,
>>>
>>> thanks for the quick reply.
>>>
>>> Steven Toth wrote:
>>>> Torben Viets wrote:
>>>>> Hello,
>>>>>
>>>>> I have a Hauppauge HVR-1700 PCI Express, I have read all posts about
>>>>> this card here, but I didn't get it working, how does it work?
>>>>
>>>> It's working fine for me on a stock 7.10 ubuntu install.
>>>>
>>>>>
>>>>> Kernel: linux-2.6.25-git10
>>>>>
>>>>> Firmware-Files:
>>>>> ls -al /lib/firmware/2.6.25-git10/
>>>>> total 416
>>>>> drwxr-xr-x 2 root root     91 Apr 27 16:27 .
>>>>> drwxr-xr-x 3 root root     25 Apr 27 16:26 ..
>>>>> -rw-r--r-- 1 root root  24878 Apr 27 16:27 dvb-fe-tda10048-1.0.fw
>>>>> -r--r--r-- 1 root root  16382 Apr 27 16:27 v4l-cx23885-avcore-01.fw
>>>>> -r--r--r-- 1 root root 376836 Apr 27 16:26 v4l-cx23885-enc.fw
>>>>>
>>>>> The modules I use are from the actual v4l-dvb hg, if I type make load,
>>>>> the only thing I get is a /dev/video0, but I have no picture with 
>>>>> xawtv...
>>>>
>>>> /dev/video doesn't work, it's not supported.
>>>>
>>> Are there any plans to support it?
>>
>>
>> No immediate plans.
>>
>>
>>>> You should aim to use the dvb-apps tools (tzap, scan) and mplayer as 
>>>> example tools, or MythTV as an app.
>>>>
>>>>
>>>>>
>>>>> The DVB doesn't work at all, I have no /dev/dvb*, here is my dmesg:
>>>>>
>>>>> cx23885 driver version 0.0.1 loaded
>>>>> ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 24 (level, low) -> IRQ 24
>>>>> CORE cx23885[0]: subsystem: 0070:8101, board: Hauppauge WinTV-HVR1700
>>>>> [card=8,autodetected]
>>>>> cx23885[0]: i2c bus 0 registered
>>>>> cx23885[0]: i2c bus 1 registered
>>>>> cx23885[0]: i2c bus 2 registered
>>>>> tveeprom 0-0050: Huh, no eeprom present (err=-5)?
>>>>> tveeprom 0-0050: Encountered bad packet header [00].
>>>>> Corrupt or not a Hauppauge
>>>>> eeprom.
>>>>> cx23885[0]: warning: unknown hauppauge model #0
>>>>> cx23885[0]: hauppauge eeprom: model=0
>>>>> cx23885[0]: cx23885 based dvb card
>>>>> tda10048_readreg: readreg error (ret == -5)
>>>>> cx23885[0]: frontend initialization failed
>>>>> cx23885_dvb_register() dvb_register failed err = -1
>>>>> cx23885_dev_setup() Failed to register dvb on VID_C
>>>>> cx23885_dev_checkrevision() New hardware revision found 0x0
>>>>> cx23885_dev_checkrevision() Hardware revision unknown 0x0
>>>>> cx23885[0]/0: found at 0000:02:00.0, rev: 2, irq: 24, latency: 0, 
>>>>> mmio:
>>>>> 0xfe800000
>>>>
>>>> This looks bad, it looks like i2c is broken badly, so that the 
>>>> eeprom isn't detected and the demodulator isn't found during attach. 
>>>> This is the reason why your missing /dev/dvb/adapterX/
>>>>
>>>> No idea why. Try loading the cx23885 with debug=5 and report any log 
>>>> messages here - on this mailing list.
>>> here ist the debug=5 output
>>>
>>> cx23885[0]/0: cx23885_dev_setup() Memory configured for PCIe bridge 
>>> type 885
>>> cx23885[0]/0: cx23885_init_tsport(portno=2)
>>> CORE cx23885[0]: subsystem: 0070:8101, board: Hauppauge WinTV-HVR1700 
>>> [card=8,autodetected]
>>> cx23885[0]/0: cx23885_pci_quirks()
>>> cx23885[0]/0: cx23885_dev_setup() tuner_type = 0x0 tuner_addr = 0x0
>>> cx23885[0]/0: cx23885_dev_setup() radio_type = 0x0 radio_addr = 0x0
>>> cx23885[0]/0: cx23885_reset()
>>> cx23885[0]/0: cx23885_sram_channel_setup() Configuring channel [VID A]
>>> cx23885[0]/0: cx23885_sram_channel_setup() 0x000107b0 <- 0x00000040
>>> cx23885[0]/0: cx23885_sram_channel_setup() 0x000107c0 <- 0x00000b80
>>> cx23885[0]/0: cx23885_sram_channel_setup() 0x000107d0 <- 0x000016c0
>>> cx23885[0]/0: [bridge 885] sram setup VID A: bpl=2880 lines=3
>>> cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch2]
>>> cx23885[0]/0: cx23885_sram_channel_setup() Configuring channel [TS1 B]
>>> cx23885[0]/0: cx23885_sram_channel_setup() 0x00010400 <- 0x00005000
>>> cx23885[0]/0: cx23885_sram_channel_setup() 0x00010410 <- 0x000052f0
>>> cx23885[0]/0: cx23885_sram_channel_setup() 0x00010420 <- 0x000055e0
>>> cx23885[0]/0: cx23885_sram_channel_setup() 0x00010430 <- 0x000058d0
>>> cx23885[0]/0: cx23885_sram_channel_setup() 0x00010440 <- 0x00005bc0
>>> cx23885[0]/0: [bridge 885] sram setup TS1 B: bpl=752 lines=5
>>> cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch4]
>>> cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch5]
>>> cx23885[0]/0: cx23885_sram_channel_setup() Configuring channel [TS2 C]
>>> cx23885[0]/0: cx23885_sram_channel_setup() 0x000108d0 <- 0x00006000
>>> cx23885[0]/0: cx23885_sram_channel_setup() 0x000108e0 <- 0x000062f0
>>> cx23885[0]/0: cx23885_sram_channel_setup() 0x000108f0 <- 0x000065e0
>>> cx23885[0]/0: cx23885_sram_channel_setup() 0x00010900 <- 0x000068d0
>>> cx23885[0]/0: cx23885_sram_channel_setup() 0x00010910 <- 0x00006bc0
>>> cx23885[0]/0: [bridge 885] sram setup TS2 C: bpl=752 lines=5
>>> cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch7]
>>> cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch8]
>>> cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch9]
>>> cx23885[0]: i2c bus 0 registered
>>> cx23885[0]: i2c bus 1 registered
>>> cx23885[0]: i2c bus 2 registered
>>
>> Everything looks fine up to this point, then i2c looks bad.
>>
>> Can you try again with modprobe cx23885 i2c_scan=1 and post the output 
>> again? (Output will be large - feel free to use pastebin.com and post 
>> the URL here).
> 
> hmm, output doesn't change with it. here is a lsmod plus a complete 
> dmesg, is some module missing?
> 
> http://pastebin.com/f4f9b58ed
> 

The module option isn't active.

Unload the cx23885 module (and any dependencies) then try modprobe 
i2c_scan=1

When the module option is set correctly, you'll see a lot of extra debug 
messages.

- Steve


_______________________________________________
linux-dvb mailing list
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

[Index of Archives]     [Linux Media]     [Video 4 Linux]     [Asterisk]     [Samba]     [Xorg]     [Xfree86]     [Linux USB]

  Powered by Linux