Torben Viets wrote: > Hello, > > thanks for the quick reply. > > Steven Toth wrote: >> Torben Viets wrote: >>> Hello, >>> >>> I have a Hauppauge HVR-1700 PCI Express, I have read all posts about >>> this card here, but I didn't get it working, how does it work? >> >> It's working fine for me on a stock 7.10 ubuntu install. >> >>> >>> Kernel: linux-2.6.25-git10 >>> >>> Firmware-Files: >>> ls -al /lib/firmware/2.6.25-git10/ >>> total 416 >>> drwxr-xr-x 2 root root 91 Apr 27 16:27 . >>> drwxr-xr-x 3 root root 25 Apr 27 16:26 .. >>> -rw-r--r-- 1 root root 24878 Apr 27 16:27 dvb-fe-tda10048-1.0.fw >>> -r--r--r-- 1 root root 16382 Apr 27 16:27 v4l-cx23885-avcore-01.fw >>> -r--r--r-- 1 root root 376836 Apr 27 16:26 v4l-cx23885-enc.fw >>> >>> The modules I use are from the actual v4l-dvb hg, if I type make load, >>> the only thing I get is a /dev/video0, but I have no picture with >>> xawtv... >> >> /dev/video doesn't work, it's not supported. >> > Are there any plans to support it? No immediate plans. >> You should aim to use the dvb-apps tools (tzap, scan) and mplayer as >> example tools, or MythTV as an app. >> >> >>> >>> The DVB doesn't work at all, I have no /dev/dvb*, here is my dmesg: >>> >>> cx23885 driver version 0.0.1 loaded >>> ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 24 (level, low) -> IRQ 24 >>> CORE cx23885[0]: subsystem: 0070:8101, board: Hauppauge WinTV-HVR1700 >>> [card=8,autodetected] >>> cx23885[0]: i2c bus 0 registered >>> cx23885[0]: i2c bus 1 registered >>> cx23885[0]: i2c bus 2 registered >>> tveeprom 0-0050: Huh, no eeprom present (err=-5)? >>> tveeprom 0-0050: Encountered bad packet header [00]. >>> Corrupt or not a Hauppauge >>> eeprom. >>> cx23885[0]: warning: unknown hauppauge model #0 >>> cx23885[0]: hauppauge eeprom: model=0 >>> cx23885[0]: cx23885 based dvb card >>> tda10048_readreg: readreg error (ret == -5) >>> cx23885[0]: frontend initialization failed >>> cx23885_dvb_register() dvb_register failed err = -1 >>> cx23885_dev_setup() Failed to register dvb on VID_C >>> cx23885_dev_checkrevision() New hardware revision found 0x0 >>> cx23885_dev_checkrevision() Hardware revision unknown 0x0 >>> cx23885[0]/0: found at 0000:02:00.0, rev: 2, irq: 24, latency: 0, mmio: >>> 0xfe800000 >> >> This looks bad, it looks like i2c is broken badly, so that the eeprom >> isn't detected and the demodulator isn't found during attach. This is >> the reason why your missing /dev/dvb/adapterX/ >> >> No idea why. Try loading the cx23885 with debug=5 and report any log >> messages here - on this mailing list. > here ist the debug=5 output > > cx23885[0]/0: cx23885_dev_setup() Memory configured for PCIe bridge type > 885 > cx23885[0]/0: cx23885_init_tsport(portno=2) > CORE cx23885[0]: subsystem: 0070:8101, board: Hauppauge WinTV-HVR1700 > [card=8,autodetected] > cx23885[0]/0: cx23885_pci_quirks() > cx23885[0]/0: cx23885_dev_setup() tuner_type = 0x0 tuner_addr = 0x0 > cx23885[0]/0: cx23885_dev_setup() radio_type = 0x0 radio_addr = 0x0 > cx23885[0]/0: cx23885_reset() > cx23885[0]/0: cx23885_sram_channel_setup() Configuring channel [VID A] > cx23885[0]/0: cx23885_sram_channel_setup() 0x000107b0 <- 0x00000040 > cx23885[0]/0: cx23885_sram_channel_setup() 0x000107c0 <- 0x00000b80 > cx23885[0]/0: cx23885_sram_channel_setup() 0x000107d0 <- 0x000016c0 > cx23885[0]/0: [bridge 885] sram setup VID A: bpl=2880 lines=3 > cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch2] > cx23885[0]/0: cx23885_sram_channel_setup() Configuring channel [TS1 B] > cx23885[0]/0: cx23885_sram_channel_setup() 0x00010400 <- 0x00005000 > cx23885[0]/0: cx23885_sram_channel_setup() 0x00010410 <- 0x000052f0 > cx23885[0]/0: cx23885_sram_channel_setup() 0x00010420 <- 0x000055e0 > cx23885[0]/0: cx23885_sram_channel_setup() 0x00010430 <- 0x000058d0 > cx23885[0]/0: cx23885_sram_channel_setup() 0x00010440 <- 0x00005bc0 > cx23885[0]/0: [bridge 885] sram setup TS1 B: bpl=752 lines=5 > cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch4] > cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch5] > cx23885[0]/0: cx23885_sram_channel_setup() Configuring channel [TS2 C] > cx23885[0]/0: cx23885_sram_channel_setup() 0x000108d0 <- 0x00006000 > cx23885[0]/0: cx23885_sram_channel_setup() 0x000108e0 <- 0x000062f0 > cx23885[0]/0: cx23885_sram_channel_setup() 0x000108f0 <- 0x000065e0 > cx23885[0]/0: cx23885_sram_channel_setup() 0x00010900 <- 0x000068d0 > cx23885[0]/0: cx23885_sram_channel_setup() 0x00010910 <- 0x00006bc0 > cx23885[0]/0: [bridge 885] sram setup TS2 C: bpl=752 lines=5 > cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch7] > cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch8] > cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch9] > cx23885[0]: i2c bus 0 registered > cx23885[0]: i2c bus 1 registered > cx23885[0]: i2c bus 2 registered Everything looks fine up to this point, then i2c looks bad. Can you try again with modprobe cx23885 i2c_scan=1 and post the output again? (Output will be large - feel free to use pastebin.com and post the URL here). Regards, Steve _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
