> > > > Also when I plugged it in, it sat there for about 10 seconds before > > finishing loading (dmesg printed another 5 lines about the device > > after about 10 seconds), but still no tuning. > > Can I see those five lines? ;-) > > While you're at it, you may as well include dmesg from the point that the bridge driver loads and on. > Here's dmesg from the point it starts up until it finishes printing stuff. usb 2-10: new high speed USB device using ehci_hcd and address 22 usb 2-10: configuration #1 chosen from 1 choice af9015_usb_probe: af9015_identify_state: reply:01 dvb-usb: found a 'Leadtek Winfast DTV Dongle Gold' in cold state, will try to load a firmware dvb-usb: downloading firmware from file 'dvb-usb-af9015.fw' af9015_download_firmware: dvb-usb: found a 'Leadtek Winfast DTV Dongle Gold' in warm state. dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. DVB: registering new adapter (Leadtek Winfast DTV Dongle Gold) af9015_eeprom_dump: 00: 31 c2 bb 0b 00 00 00 00 13 04 29 60 00 02 01 02 10: 00 80 00 fa fa 10 40 ef 01 30 31 30 31 30 32 30 20: 35 30 35 30 30 30 30 31 ff ff ff ff ff ff ff ff 30: 00 00 3a 01 00 08 02 00 cc 10 00 00 9c ff ff ff 40: ff ff ff ff ff 08 02 00 1d 8d c4 04 82 ff ff ff 50: ff ff ff ff ff 26 00 00 04 03 09 04 10 03 4c 00 60: 65 00 61 00 64 00 74 00 65 00 6b 00 30 03 57 00 70: 69 00 6e 00 46 00 61 00 73 00 74 00 20 00 44 00 80: 54 00 56 00 20 00 44 00 6f 00 6e 00 67 00 6c 00 90: 65 00 20 00 47 00 6f 00 6c 00 64 00 20 03 30 00 a0: 31 00 30 00 31 00 30 00 31 00 30 00 31 00 30 00 b0: 36 00 30 00 30 00 30 00 30 00 31 00 00 ff ff ff c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff af9015_read_config: xtal:2 set adc_clock:28000 af9015_read_config: tuner id1:156 af9015_read_config: spectral inversion:0 af9015_set_gpios: af9013: firmware version:4.95.0 DVB: registering frontend 2 (Afatech AF9013 DVB-T)... af9015_tuner_attach: tda18271_tuner_attach: tda18271 5-00c0: creating new instance TDA18271HD/C1 detected @ 5-00c0 input: IR-receiver inside an USB DVB receiver as /class/input/input34 dvb-usb: schedule remote query interval to 200 msecs. dvb-usb: Leadtek Winfast DTV Dongle Gold successfully initialized and connected. af9015_init: af9015_download_ir_table: input: Leadtek WinFast DTV Dongle Gold as /class/input/input35 input: USB HID v1.01 Keyboard [Leadtek WinFast DTV Dongle Gold] on usb-0000:00:02.1-10 > > You said that you tuned to "channel 7, sydney, australia" -- is that an 8 MHz channel? What frequency is it on? > This is channel 7's entry in channels.conf: 7 Digital:177500000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_2_3:FEC_2_3:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_16:HIERARCHY_NONE:513:514:1312 Jarryd. _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
