Hi Egidio,
Am Donnerstag, den 10.05.2007, 18:14 +0200 schrieb Egidio:
> hermann pitton ha scritto:
> > Am Mittwoch, den 09.05.2007, 23:21 +0200 schrieb Egidio:
> >
> > > :-D 8-) 8-)
> > >
> > > cool very cool...
> > >
> > > I recompiled only saa7134_dvb.c as you mentioned .... 8-)
> > >
> > > Yes it works!
> > >
> > > see the dmesg for saa:
> > >
> > >
> > > saa7130/34: v4l2 driver version 0.2.14 loaded
> > > saa7133[0]: found at 0000:02:09.0, rev: 209, irq: 20, latency: 32,
> > > mmio: 0xed000000
> > > saa7133[0]: subsystem: 1822:0022, board: Philips Tiger - S Reference
> > > design [card=109,insmod option]
> > > saa7133[0]: board init: gpio is 40000
> > > saa7133[0]: i2c eeprom 00: 22 18 22 00 54 20 1c 00 43 43 a9 1c 55 d2
> > > b2 92
> > > saa7133[0]: i2c eeprom 10: 00 01 fb 00 ff 20 ff ff ff ff ff ff ff ff
> > > ff ff
> > > saa7133[0]: i2c eeprom 20: 01 40 01 02 03 01 01 03 08 ff 00 10 ff ff
> > > ff ff
> > > saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> > > ff ff
> > > saa7133[0]: i2c eeprom 40: ff 21 00 c2 84 10 03 32 15 50 ff ff ff ff
> > > ff ff
> > > saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> > > ff ff
> > > saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> > > ff ff
> > > saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> > > ff ff
> > > saa7133[0]: i2c scan: found device @ 0x10 [???]
> > > saa7133[0]: i2c scan: found device @ 0x84 [???]
> > > saa7133[0]: i2c scan: found device @ 0xa0 [eeprom]
> > > tuner 0-0042: chip found @ 0x84 (saa7133[0])
> > > saa7133[0]: registered device video0 [v4l2]
> > > saa7133[0]: registered device vbi0
> > > saa7133[0]: registered device radio0
> > > saa7134 ALSA driver for DMA sound loaded
> > > saa7133[0]/alsa: saa7133[0] at 0xed000000 irq 20 registered as card -2
> > > DVB: registering new adapter (saa7133[0]).
> > >
> > >
> > > see the dmesg for tda
> > >
> > > tda1004x: setting up plls for 48MHz sampling clock
> > > tda1004x: timeout waiting for DSP ready
> > > tda1004x: found firmware revision 0 -- invalid
> > > tda1004x: trying to boot from eeprom
> > > tda1004x: found firmware revision 0 -- invalid
> > > tda1004x: waiting for firmware upload...
> > > tda1004x: found firmware revision 29 -- ok
> > > tda1004x: setting up plls for 48MHz sampling clock
> > > tda1004x: found firmware revision 29 -- ok
> > > tda1004x: setting up plls for 48MHz sampling clock
> > > tda1004x: found firmware revision 29 -- ok
> > >
> > > see the kaffeine
> > >
> > > Using DVB device 0:0 "Philips TDA10046H DVB-T"
> > > tuning DVB-T to 810000000 Hz
> > > inv:2 bw:0 fecH:2 fecL:1 mod:3 tm:1 gi:0 hier:0
> > > .... LOCKED.
> > > Transponders: 1/7
> > > Reading SDT: pid=17
> > > Rete 4: sid=11
> > > Italia 1: sid=12
> > > Teleradio Padre Pio: sid=13
> > > Sportitalia: sid=14
> > > ecc...
> > >
> > >
> > > Radio is ok with gnome radio
> > > Analog TV is ok with kdetv and tvtime
> > > Composite 1 is also ok and with audio too... I see was just an issue
> > > to set in gnome mixer the capture for saa7134 audio driver
> > >
> > > Also I tested that with only
> > >
> > > sox -r 32000 -w -t alsa hw:1,0 -t alsa hw:0,0
> > >
> > > I can hear audio from analog source... dvb it not need!
> > >
> > > THANK YOU!
> > > :-*
> > >
> > >
> > > P.S.
> > > That jpg is my card!
> > > _____________________________________________
> > >
> > >
> > >
> > >
> > > hermann pitton ha scritto:
> > >
> > > > Hi,
> > > >
> > > > Am Sonntag, den 06.05.2007, 11:54 +0200 schrieb Egidio:
> > > >
> > > >
> > > > > Just one more bit for my problem....
> > > > >
> > > > >
> > > > > Some my work around shows that with this:
> > > > >
> > > > > arecord -D hw:1,0 -r 32000 -c 2 -f S16_LE | sox -q -c 2 -r 32000 -w -t
> > > > > wav - -t alsa hw:0,0
> > > > >
> > > > > I can get AUDIO from Analog TV Tuner but no from external source
> > > > > Composite1. :-)
> > > > >
> > > > >
> > > > please try to change .amux LINE1 for comp1 and svideo to LINE2 in
> > > > saa7134-cards.c for the TIGER_S.
> > > >
> > > > Is there a audio mux chip on the board or can you provide a high
> > > > resolution photo.
> > > >
> > > > Related, does radio work?
> > > >
> > > >
> > > >
> > > > > Still not working DVB.
> > > > >
> > > > >
> > > > Please try to change in saa7134-dvb.c
> > > >
> > > > static struct tda1004x_config philips_tiger_s_config = {
> > > > .demod_address = 0x08,
> > > > .invert = 1,
> > > > .invert_oclk = 0,
> > > > .xtal_freq = TDA10046_XTAL_16M,
> > > > .agc_config = TDA10046_AGC_TDA827X,
> > > > .gpio_config = TDA10046_GP01_I,
> > > > .if_freq = TDA10046_FREQ_045,
> > > > .i2c_gate = 0x4b,
> > > > .tuner_address = 0x61,
> > > > .tuner_config = 2,
> > > > .antenna_switch= 1,
> > > > .request_firmware = philips_tda1004x_request_firmware
> > > > };
> > > >
> > > > .i2c_gate from 0x4b to 0x42 and recompile.
> > > >
> > > > Good luck,
> > > >
> > > > Hermann
> > > >
> > > >
> > > >
> > > >
> > > > > Help!
> > > > > Ciao.
> > > > >
> > > > > ______________________________
> > > > >
> > > > >
> > > > >
> > > > >
> > > > > > Hi Linux-dvb developers,
> > > > > >
> > > > > > here is my problem... I bought the card in subject in a computer store
> > > > > > that under XP is reconised as: DTV-DVB 3056 Hybrid HID PCI capture
> > > > > > card but under LINUX it won't know to be supported and work correctly.
> > > > > > (see www.twinhan.com/product_D%2BA_3056_1.asp for more info)
> > > > > >
> > > > > > Some my work around put me in this situation, I can get a minimal
> > > > > > working if I force saa7134 as card=109, in this way kdetv scan analog
> > > > > > TV and show me the video in a very good way but no AUDIO, kaffeine or
> > > > > > scan (dvb utilitis) are ko and I still didn't try FM + lirc.
> > > > > >
> > > > > > If you see below a problem occur in communication between saa7134 and
> > > > > > Tuner that appear to me as the main issue.
> > > > > >
> > > > > > I am not a developer (I am not able to write codes) but if someone of
> > > > > > you guide me to make some tests and debugs, I am very happy :-) and we
> > > > > > could have made one more goals for the opensource comunity :-) so
> > > > > > other folks with my same card can get help.
> > > > > >
> > > > > > Here is a brief of what says kaffeine:
> > > > > >
> > > > > > ........
> > > > > > Not able to lock to the signal on the given frequency
> > > > > > Frontend closed
> > > > > > dvbsi: Cant tune DVB
> > > > > > Using DVB device 0:0 "Philips TDA10046H DVB-T"
> > > > > > tuning DVB-T to 602000000 Hz
> > > > > > inv:2 bw:0 fecH:1 fecL:9 mod:3 tm:1 gi:3 hier:0
> > > > > > ...............
> > > > > >
> > > > > > And here is what says dmesg:
> > > > > >
> > > > > > saa7130/34: v4l2 driver version 0.2.14 loaded
> > > > > > saa7133[0]: found at 0000:02:09.0, rev: 209, irq: 20, latency: 32,
> > > > > > mmio: 0xed000000
> > > > > > saa7133[0]: subsystem: 1822:0022, board: Philips Tiger - S Reference
> > > > > > design [card=109,insmod option]
> > > > > > saa7133[0]: board init: gpio is 40000
> > > > > > tuner 0-0042: chip found @ 0x84 (saa7133[0])
> > > > > > tuner 0-0042: setting tuner address to 61
> > > > > > tuner 0-0042: type set to tda8290+75a
> > > > > > tuner 0-0042: setting tuner address to 61
> > > > > > tuner 0-0042: type set to tda8290+75a
> > > > > > saa7133[0]: i2c eeprom 00: 22 18 22 00 54 20 1c 00 43 43 a9 1c 55 d2
> > > > > > b2 92
> > > > > > saa7133[0]: i2c eeprom 10: 00 01 fb 00 ff 20 ff ff ff ff ff ff ff ff
> > > > > > ff ff
> > > > > > saa7133[0]: i2c eeprom 20: 01 40 01 02 03 01 01 03 08 ff 00 10 ff ff
> > > > > > ff ff
> > > > > > saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> > > > > > ff ff
> > > > > > saa7133[0]: i2c eeprom 40: ff 21 00 c2 84 10 03 32 15 50 ff ff ff ff
> > > > > > ff ff
> > > > > > saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> > > > > > ff ff
> > > > > > saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> > > > > > ff ff
> > > > > > saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> > > > > > ff ff
> > > > > > saa7133[0]: registered device video0 [v4l2]
> > > > > > saa7133[0]: registered device vbi0
> > > > > > saa7133[0]: registered device radio0
> > > > > > DVB: registering new adapter (saa7133[0]).
> > > > > > DVB: registering frontend 0 (Philips TDA10046H DVB-T)...
> > > > > > tda1004x: setting up plls for 48MHz sampling clock
> > > > > > saa7134 ALSA driver for DMA sound loaded
> > > > > > saa7133[0]/alsa: saa7133[0] at 0xed000000 irq 20 registered as card -2
> > > > > > tda1004x: found firmware revision 29 -- ok
> > > > > > saa7133[0]/dvb: could not access tda8290 I2C gate
> > > > > > tda827x_probe_version: could not read from tuner at addr: 0xc2
> > > > > > tda1004x: setting up plls for 48MHz sampling clock
> > > > > > tda1004x: found firmware revision 29 -- ok
> > > > > > saa7133[0]/dvb: could not access tda8290 I2C gate
> > > > > > tda827x_probe_version: could not read from tuner at addr: 0xc2
> > > > > > saa7133[0]/dvb: could not access tda8290 I2C gate
> > > > > > saa7133[0]/dvb: could not access tda8290 I2C gate
> > > > > > tda827x_probe_version: could not read from tuner at addr: 0xc2
> > > > > > saa7133[0]/dvb: could not access tda8290 I2C gate
> > > > > > tda1004x: setting up plls for 48MHz sampling clock
> > > > > > tda1004x: found firmware revision 29 -- ok
> > > > > > saa7133[0]/dvb: could not access tda8290 I2C gate
> > > > > > tda827x_probe_version: could not read from tuner at addr: 0xc2
> > > > > >
> > > > > > As I said to me the problem seems a comunication problems with the tuner.
> > > > > >
> > > > > > I am sure that the main chips mounted on the board are saa7131E and
> > > > > > TDA 10046A, the only quarz I see is a 32.1F6G and unfortunately I
> > > > > > can't see last chip near the antenna inputs because a metallic box
> > > > > > covers that part.
> > > > > >
> > > > > > This card is a Analog TV + DVB + FM + Capture card (composite source +
> > > > > > S-video), all inputs (AUDIO included) are on the card.
> > > > > >
> > > > > > My distro is UBUNTU Feisty 7.04 with kernel 2.6.20-15-generic and
> > > > > > this is what lspci -vv says about my card:
> > > > > >
> > > > > > 02:09.0 Multimedia controller: Philips Semiconductors SAA7133/SAA7135
> > > > > > Video Broadcast Decoder (rev d1)
> > > > > > Subsystem: Twinhan Technology Co. Ltd Unknown device 0022
> > > > > > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV-
> > > > > > VGASnoop- ParErr- Stepping- SERR- FastB2B-
> > > > > > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
> > > > > >
> > > > > >
> > > > > > > TAbort- <TAbort- <MAbort- >SERR- <PERR-
> > > > > > >
> > > > > > >
> > > > > > Latency: 32 (21000ns min, 8000ns max)
> > > > > > Interrupt: pin A routed to IRQ 20
> > > > > > Region 0: Memory at ed000000 (32-bit, non-prefetchable)
> > > > > > [size=2K]
> > > > > > Capabilities: <access denied>
> > > > > >
> > > > > >
> > > > > > Guys a big Thank you to who will help me!
> > > > > > :-)
> > > > > >
> > > > > > Ciao!
> > > > > >
> > > > > >
> >
> >
> > Hi Egidio,
> >
> > thanks for testing and have fun!
> >
> > Take some more time to test all, see also Hartmut's previous
> > instructions in case of a LowNoiseAmplifier (LNA) is present on the
> > lists.
> >
> > Don't bother to ask further questions, in case of analog issues you
> > might drop over to the video4linux-list.
> >
> > If you are through, please send us a patch with your SOB.
> >
> > Cheers,
> > Hermann
> >
> >
> Hi herman,
> just to be clear of what more test you ask.
>
> Actually to get audio I do:
>
> 1. sox -r 32000 -w -t alsa hw:1,0 -t alsa hw:0,0 in a terminal window
> 2. I select in gnome mixer the saa7134 device and under this device I
> just click in switch (interrutori) tab for:
> a) selecting a voice/block called video - for Analog TV & RADIO
> audio
yes, this is OK.
> b) selecting a voice/block called capture channel 1 for Composite
> 1 audio
> c) selecting a voice/block called capture channel 2 for S-video
> audio
>
> I sow that in the tab window volume (gnome mixer in saa7134 device)
> the singles volume adjustion has no effect.
Current behavior and OK too. We can keep the .amux from the TIGER_S.
> Now with this scenario what test you want do I do?
With sound on radio the antenna input switching should be fine.
If no issues with DVB-T and analog picture the LNA config should be fine
too. Also firmware loading is clear, no firmware eeprom there.
> More what you mean for "please send us a patch with your SOB"??
> what's "SOB"??
"Signed-off-by" followed by your name and email addr.
http://linuxtv.org/v4lwiki/index.php/SubmittingPatches#Sign_your_work
I can provide the patch for you, but need your SOB after testing it.
> Lirc is still not tested.
Nothing would happen. The Philips reference TIGER_S design has no
remote. How many keys yours has and is some model name on it?
Maybe others have a clue if you upload a picture somewhere (don't send
such to the lists, but to Gunther at the bttv-gallery.de, like all other
information he requires) or it is a known DTV variant.
We have info on the v4l-wiki how to deal with remotes.
Likely on the gpio 0x040000 pin at least key down/up is connected.
A shot in the dark, try card=78, enable debug=1 for the ir-common
module. Check "dmesg" what happens when pressing number keys etc.
Unlikely that anything matches.
Allow me to send a copy to the video4linux-list, then we can cut down
previous stuff next.
Cheers,
Hermann
_______________________________________________
linux-dvb mailing list
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
