Re: Twinhan DTV-DVB 3056 Hybrid HID PCI won't work

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi,

Am Sonntag, den 06.05.2007, 11:54 +0200 schrieb Egidio:
> Just one more bit for my problem....
> 
> 
> Some my work around shows that with this:
> 
> arecord -D hw:1,0 -r 32000 -c 2 -f S16_LE | sox -q -c 2 -r 32000 -w -t 
> wav - -t alsa hw:0,0
> 
> I can get AUDIO from Analog TV Tuner but no from external source 
> Composite1. :-)

please try to change .amux LINE1 for comp1 and svideo to LINE2 in
saa7134-cards.c for the TIGER_S.

Is there a audio mux chip on the board or can you provide a high
resolution photo.

Related, does radio work?

> Still not working DVB.

Please try to change in saa7134-dvb.c

static struct tda1004x_config philips_tiger_s_config = {
	.demod_address = 0x08,
	.invert        = 1,
	.invert_oclk   = 0,
	.xtal_freq     = TDA10046_XTAL_16M,
	.agc_config    = TDA10046_AGC_TDA827X,
	.gpio_config   = TDA10046_GP01_I,
	.if_freq       = TDA10046_FREQ_045,
	.i2c_gate      = 0x4b,
	.tuner_address = 0x61,
	.tuner_config  = 2,
	.antenna_switch= 1,
	.request_firmware = philips_tda1004x_request_firmware
};

.i2c_gate from 0x4b to 0x42 and recompile.

Good luck,

Hermann


> Help!
> Ciao.
> 
> ______________________________
> 
> 
> > Hi Linux-dvb developers,
> >
> > here is my problem... I bought the card in subject in a computer store 
> > that under XP is reconised as: DTV-DVB 3056 Hybrid HID PCI capture 
> > card but under LINUX it won't know to be supported and work correctly.
> > (see www.twinhan.com/product_D%2BA_3056_1.asp for more info)
> >
> > Some my work around put me in this situation, I can get a minimal 
> > working if I force saa7134 as card=109, in this way kdetv scan analog 
> > TV and show me the video in a very good way but no AUDIO, kaffeine or 
> > scan (dvb utilitis) are ko and I still didn't try FM + lirc.
> >
> > If you see below a problem occur in communication between saa7134 and 
> > Tuner that appear to me as the main issue.
> >
> > I am not a developer (I am not able to write codes) but if someone of 
> > you guide me to make some tests and debugs, I am very happy :-) and we 
> > could have made one more goals for the opensource comunity :-) so 
> > other folks with my same card can get help.
> >
> > Here is a brief of what says kaffeine:
> >
> > ........
> > Not able to lock to the signal on the given frequency
> > Frontend closed
> > dvbsi: Cant tune DVB
> > Using DVB device 0:0 "Philips TDA10046H DVB-T"
> > tuning DVB-T to 602000000 Hz
> > inv:2 bw:0 fecH:1 fecL:9 mod:3 tm:1 gi:3 hier:0
> > ...............
> >
> > And here is what says dmesg:
> >
> > saa7130/34: v4l2 driver version 0.2.14 loaded
> > saa7133[0]: found at 0000:02:09.0, rev: 209, irq: 20, latency: 32, 
> > mmio: 0xed000000
> > saa7133[0]: subsystem: 1822:0022, board: Philips Tiger - S Reference 
> > design [card=109,insmod option]
> > saa7133[0]: board init: gpio is 40000
> > tuner 0-0042: chip found @ 0x84 (saa7133[0])
> > tuner 0-0042: setting tuner address to 61
> > tuner 0-0042: type set to tda8290+75a
> > tuner 0-0042: setting tuner address to 61
> > tuner 0-0042: type set to tda8290+75a
> > saa7133[0]: i2c eeprom 00: 22 18 22 00 54 20 1c 00 43 43 a9 1c 55 d2 
> > b2 92
> > saa7133[0]: i2c eeprom 10: 00 01 fb 00 ff 20 ff ff ff ff ff ff ff ff 
> > ff ff
> > saa7133[0]: i2c eeprom 20: 01 40 01 02 03 01 01 03 08 ff 00 10 ff ff 
> > ff ff
> > saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
> > ff ff
> > saa7133[0]: i2c eeprom 40: ff 21 00 c2 84 10 03 32 15 50 ff ff ff ff 
> > ff ff
> > saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
> > ff ff
> > saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
> > ff ff
> > saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
> > ff ff
> > saa7133[0]: registered device video0 [v4l2]
> > saa7133[0]: registered device vbi0
> > saa7133[0]: registered device radio0
> > DVB: registering new adapter (saa7133[0]).
> > DVB: registering frontend 0 (Philips TDA10046H DVB-T)...
> > tda1004x: setting up plls for 48MHz sampling clock
> > saa7134 ALSA driver for DMA sound loaded
> > saa7133[0]/alsa: saa7133[0] at 0xed000000 irq 20 registered as card -2
> > tda1004x: found firmware revision 29 -- ok
> > saa7133[0]/dvb: could not access tda8290 I2C gate
> > tda827x_probe_version: could not read from tuner at addr: 0xc2
> > tda1004x: setting up plls for 48MHz sampling clock
> > tda1004x: found firmware revision 29 -- ok
> > saa7133[0]/dvb: could not access tda8290 I2C gate
> > tda827x_probe_version: could not read from tuner at addr: 0xc2
> > saa7133[0]/dvb: could not access tda8290 I2C gate
> > saa7133[0]/dvb: could not access tda8290 I2C gate
> > tda827x_probe_version: could not read from tuner at addr: 0xc2
> > saa7133[0]/dvb: could not access tda8290 I2C gate
> > tda1004x: setting up plls for 48MHz sampling clock
> > tda1004x: found firmware revision 29 -- ok
> > saa7133[0]/dvb: could not access tda8290 I2C gate
> > tda827x_probe_version: could not read from tuner at addr: 0xc2
> >
> > As I said to me the problem seems a comunication problems with the tuner.
> >
> > I am sure that the main chips mounted on the board are saa7131E and 
> > TDA 10046A, the only quarz I see is a 32.1F6G and unfortunately I 
> > can't see last chip near the antenna inputs because a metallic box 
> > covers that part.
> >
> > This card is a Analog TV + DVB + FM + Capture card (composite source + 
> > S-video), all inputs (AUDIO included) are on the card.
> >
> > My distro is UBUNTU Feisty  7.04 with kernel  2.6.20-15-generic and 
> > this is what lspci -vv says about my card:
> >
> > 02:09.0 Multimedia controller: Philips Semiconductors SAA7133/SAA7135 
> > Video Broadcast Decoder (rev d1)
> >             Subsystem: Twinhan Technology Co. Ltd Unknown device 0022
> >             Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- 
> > VGASnoop- ParErr- Stepping- SERR- FastB2B-
> >             Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium 
> > >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> >             Latency: 32 (21000ns min, 8000ns max)
> >             Interrupt: pin A routed to IRQ 20
> >             Region 0: Memory at ed000000 (32-bit, non-prefetchable) 
> > [size=2K]
> >             Capabilities: <access denied>
> >
> >
> > Guys a big Thank you to who will help me!
> > :-)
> >
> > Ciao!
> >
> > _______________________________________________
> > linux-dvb mailing list
> > linux-dvb@xxxxxxxxxxx
> > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
> >
> 
> 
> _______________________________________________
> linux-dvb mailing list
> linux-dvb@xxxxxxxxxxx
> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb


_______________________________________________
linux-dvb mailing list
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

[Index of Archives]     [Linux Media]     [Video 4 Linux]     [Asterisk]     [Samba]     [Xorg]     [Xfree86]     [Linux USB]

  Powered by Linux