Hi Greg,
On Wed, Jun 5, 2019 at 6:01 AM Greg Ungerer <gerg@xxxxxxxxxx> wrote:
>
> Hi Sergio,
>
> On 4/6/19 7:36 pm, Sergio Paracuellos wrote:
> > On Tue, Jun 4, 2019 at 9:14 AM Greg Ungerer <gerg@xxxxxxxxxx> wrote:
> >> On 4/6/19 3:06 pm, Sergio Paracuellos wrote:
> >>> On Tue, Jun 4, 2019 at 3:31 AM Greg Ungerer <gerg@xxxxxxxxxx> wrote:
> >>>> On 4/6/19 5:59 am, Sergio Paracuellos wrote:
> >>>>> On Mon, Jun 3, 2019 at 2:32 PM Greg Ungerer <gerg@xxxxxxxxxx> wrote:
> >>>>>> On 3/6/19 3:34 pm, Sergio Paracuellos wrote:
> >>>>>>> On Mon, Jun 3, 2019 at 3:26 AM Greg Ungerer <gerg@xxxxxxxxxx> wrote:
> >>>>>>>> On 31/5/19 10:37 pm, Sergio Paracuellos wrote:
> >>>>>>>>> On Thu, May 30, 2019 at 3:46 AM Greg Ungerer <gerg@xxxxxxxxxx> wrote:
> >>>>>>>>>> On 30/5/19 10:44 am, Greg Ungerer wrote:
> >>>>>>>>>>> On 29/5/19 6:08 pm, Sergio Paracuellos wrote:
> >>>>>>>>>>> [snip]
> >>>>>>> Can you try to read and set BIT(10) instead of write it directly?:
> >>>>>>>
> >>>>>>> Instead of:
> >>>>>>>
> >>>>>>> rt_sysc_w32(PERST_MODE_GPIO, MT7621_GPIO_MODE);
> >>>>>>
> >>>>>> Oh, yeah, that is definitely not going to work. There is a bunch of
> >>>>>> other GPIO control bits in there for other hardware blocks. Would
> >>>>>> explain the broken NAND flash behavior...
> >>>>>
> >>>>> Yes, my bad here. Sometimes is better to go to sleep :)).
> >>>>>>
> >>>>>>> Do:
> >>>>>>>
> >>>>>>> u32 val = rt_sysc_r32(MT7621_GPIO_MODE);
> >>>>>>> val |= PERST_MODE_GPIO;
> >>>>>>> rt_sysc_w32(val, MT7621_GPIO_MODE);
> >>>>>>
> >>>>>> Much better result with that. Though ultimately it should clear
> >>>>>> bits 10 and 11 (both are PERST_MODE bits) and then OR in BIT(10).
> >>>>>
> >>>>> Ok, so the following should do the trick:
> >>>>>
> >>>>> rt_sysc_m32(PERST_MODE_MASK, PERST_MODE_GPIO, MT7621_GPIO_MODE);
> >>>>>
> >>>>> with PERST_MODE_MASK defined as:
> >>>>>
> >>>>> #define PERST_MODE_MASK GENMASK(11, 10)
> >>>>>
> >>>>> (patch attached with this changes)
> >>>>
> >>>> I have mostly good news and a little bad news :-)
> >>>>
> >>>> I should have tested more thoroughly last night. Anyway, the new patch
> >>>> works, even the IRQ of the PCI device. My Wifi PCI device works just
> >>>> as well now as it did with the 4.20 pci-mt7621.c/pci-mt7621-phy.c.
> >>>> I still get the lines:
> >>>>
> >>>> pcieport 0000:00:00.0: of_irq_parse_pci: failed with rc=-22
> >>>> pcieport 0000:00:00.0: enabling device (0004 -> 0006)
> >>>>
> >>>> However that is referring to the root host PCI device (0000:00:00.0),
> >>>> not my PCI peripheral device (which is 0000:01:00.0). It is actually
> >>>> probed and working properly.
> >>>>
> >>>> That is the good news.
> >>>
> >>> That makes sense :). Good news are always good news even bads are
> >>> coming also :))
> >>>
> >>>>
> >>>>
> >>>>> It would be also good to know what happen if you comment the following lines:
> >>>>>
> >>>>> pcie_write(pcie, 0xffffffff, RALINK_PCI_MEMBASE);
> >>>>> pcie_write(pcie, RALINK_PCI_IO_MAP_BASE, RALINK_PCI_IOBASE);
> >>>>>
> >>>>> Are they really needed?
> >>>>
> >>>> Had no effect for me. Everything worked the same with or without
> >>>> those lines as far as I could tell.
> >>>
> >>> Ok, I won't include them when I send a clean patch series with all of
> >>> this changes.
> >>>
> >>>>
> >>>>
> >>>> [snip]
> >>>>> Only one step more to get this properly working.
> >>>>
> >>>> Ok, now the bad news.
> >>>>
> >>>> I often get the boot hanging at various points in the PCI
> >>>> initialization, setup and probing.
> >>>>
> >>>> For example sometimes it hangs with boot up to:
> >>>>
> >>>> mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
> >>>>
> >>>>
> >>>> Then sometimes it hangs at:
> >>>>
> >>>> mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
> >>>> mt7621-pci 1e140000.pcie: Port 454043648 N_FTS = 0
> >>>> mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
> >>>> mt7621-pci 1e140000.pcie: Port 454043648 N_FTS = 1
> >>>> mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
> >>>> mt7621-pci 1e140000.pcie: Port 454043648 N_FTS = 2
> >>>> mt7621-pci 1e140000.pcie: pcie0 no card, disable it (RST & CLK)
> >>>> mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK)
> >>>> mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
> >>>>
> >>>
> >>> It is weird, here it is not initializing any port... All of them are disabled.
> >>>
> >>>>
> >>>> And then I also see it hang up to:
> >>>>
> >>>> mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
> >>>> mt7621-pci 1e140000.pcie: Port 454043648 N_FTS = 0
> >>>> mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
> >>>> mt7621-pci 1e140000.pcie: Port 454043648 N_FTS = 1
> >>>> mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
> >>>> mt7621-pci 1e140000.pcie: Port 454043648 N_FTS = 2
> >>>> mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK)
> >>>> mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
> >>>> mt7621-pci 1e140000.pcie: PCIE0 enabled
> >>>> mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
> >>>> mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
> >>>> pci_bus 0000:00: root bus resource [io 0xffffffff]
> >>>> pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
> >>>> pci_bus 0000:00: root bus resource [bus 00-ff]
> >>>> pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
> >>>>
> >>>>
> >>>> It happens on cold or warm boots. Sometimes it boots up all the
> >>>> way and everything works perfectly.
> >>>
> >>> Can you try to change all the msleeps of the code driver in favour of
> >>> mdelay's? Looks like
> >>> some timing problem.
> >>
> >> Changed the msleeps to mdelays and it still hangs somtimes.
> >> I doubled the delay times in the msleeps and tried that too -
> >> that also sometimes hangs.
> >>
> >>
> >>> If it doesn't work, it would be great to have a full trace of working
> >>> 4.20 and no working current 5.x series
> >>> version just to carefully compare them.
> >>
> >> I'll attach at the end a full working boot trace from 5.1 with the 4.20 pci-mt7621.c.
> >> I'll attach a 5.1 boot trace with your patch and hang below. Not that this very
> >> same image doesn't always hang. Same binary will sometimes boot fine.
> >>
> >>
> >>>> I had perfect reliable boot and operation with linux-5.1 using the
> >>>> older 4.20 pci-mt7621.c and pci-mt7621-phy.c.
> >>>
> >>> AFAICT, there is not pci-mt7621-phy.c in the v4.20, isn't it? Do you
> >>> mean you put also that
> >>> code into that version and compile them? Or are you just using "pci-mt7621.c"?
> >>
> >> I just leave that pci-mt7621-phy.c code in place in linux-5.1 when I copy in
> >> the linux-4.20 pci-mt7621.c - even though it isn't used in that case.
> >>
> >> One thing I always notice is that the PCI probing happens much earlier
> >> with the 4.20 pci-mt7621.c. Not sure that will have any impact though.
> >>
> >
> > It seems it is related because, looking at the trace which hangs I can see:
> >
> > mt7621-pci 1e140000.pcie: failed to get gpio perst
> > mt7621-pci 1e140000.pcie: Parsing DT failed
> >
> > At that point gpio's driver are not being probed yet. This not happen
> > with the original
> > patch because it just access to memory to set up all the stuff intead
> > of use the gpio's
> > consumers apis which, IMHO, is the way to go.
> >
> > Can you try to return "-EPROBE_DEFER" if getting the gpio fails in
> > initialization?
> >
> > (patch attached with this change and removing the two lines which
> > seems to not be needed
> > commented in previous patch)
>
> New patch tried. Behavior is no different. Occasional hang during boot.
> I can see that it does the probe, and now deferr. Full boot log of a
> hung boot below.
Ok, so that means it was properly being deferred with the previous patch also.
The original code set up all at a very early stage (arch_initcall)
just after the pinctrl
driver is being set up. The new one without my last patches was also
being executed
later because of the phy. At arch_initcall the 'phy_create()' is
called before the phy module is initialized, so 'phy_class' is NULL,
the new phy isn't placed in the right class, and it cannot be found.
So the phy driver uses 'module_init' instead of 'arch_initcall' and it
worked for the gnubee board. But according to your traces when it
hangs the problem seems to be with gpio's being resetting or something
so the pcie link is not in up
state for any reason I cannot understand. So we have to determine if
the problem is because of the phy and gpio init being done in later
stages.
We can try to change 'arch_initcall' to a later stage changing it to
'module_init' to see if it is a deferring problem or something. The
other thing we can try to determine if it is a gpio access problem is
to change in the last patch
the gpio descriptor uses with you initial memory accessign hack to see
if it eventually hungs or not. If this both tests result in eventually
hung boot I'll try to prepare a patch with the current phy code in the
'arch_initcall' stage putting in the the same pci-mt7621.c file to see
if order matters. No more ideas by now, sorry :(
> Regards
> Greg
Best regards,
Sergio Paracuellos
>
>
> --------------------------------------------------------------------------------
> Linux version 5.1.0-ac0 (gerg@goober) (gcc version 5.4.0 (GCC)) #78 SMP Wed Jun 5 13:45:19 AEST 2019
> SoC Type: MediaTek MT7621 ver:1 eco:3
> printk: bootconsole [early0] enabled
> CPU0 revision is: 0001992f (MIPS 1004Kc)
> OF: fdt: No chosen node found, continuing without
> MIPS: machine is Digi EX15
> Determined physical RAM map:
> memory: 10000000 @ 00000000 (usable)
> Initial ramdisk at: 0x81000000 (16920576 bytes)
> VPE topology {2,2} total 4
> Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
> Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
> MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
> Zone ranges:
> Normal [mem 0x0000000000000000-0x000000000fffffff]
> Movable zone start for each node
> Early memory node ranges
> node 0: [mem 0x0000000000000000-0x000000000fffffff]
> Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
> random: get_random_bytes called from start_kernel+0xb0/0x524 with crng_init=0
> percpu: Embedded 15 pages/cpu s30144 r8192 d23104 u61440
> Built 1 zonelists, mobility grouping on. Total pages: 65024
> Kernel command line: boot=network boot_ver=19.3.223.0-0c02c07312-dirty console=ttyS0,115200 ubi.mtd=3 root=/dev/ram0 rd_start=0x81000000 rd_size=0x1023000
> Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
> Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
> Writing ErrCtl register=00020513
> Readback ErrCtl register=00020513
> Memory: 233756K/262144K available (7216K kernel code, 247K rwdata, 1320K rodata, 292K init, 230K bss, 28388K reserved, 0K cma-reserved)
> SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
> rcu: Hierarchical RCU implementation.
> rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
> NR_IRQS: 256
> clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
> sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 21474836475000000ns
> Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
> pid_max: default: 32768 minimum: 301
> Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
> Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
> rcu: Hierarchical SRCU implementation.
> smp: Bringing up secondary CPUs ...
> Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
> Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
> MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
> CPU1 revision is: 0001992f (MIPS 1004Kc)
> Synchronize counters for CPU 1: done.
> Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
> Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
> MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
> CPU2 revision is: 0001992f (MIPS 1004Kc)
> Synchronize counters for CPU 2: done.
> Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
> Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
> MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
> CPU3 revision is: 0001992f (MIPS 1004Kc)
> Synchronize counters for CPU 3: done.
> smp: Brought up 1 node, 4 CPUs
> devtmpfs: initialized
> clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
> futex hash table entries: 1024 (order: 3, 32768 bytes)
> pinctrl core: initialized pinctrl subsystem
> NET: Registered protocol family 16
> mt7621-pci 1e140000.pcie: failed to get gpio perst
> mt7621-pci 1e140000.pcie: Parsing DT failed
> SCSI subsystem initialized
> usbcore: registered new interface driver usbfs
> usbcore: registered new interface driver hub
> usbcore: registered new device driver usb
> pcf857x 0-0026: probed
> i2c-mt7621 1e000900.i2c: clock 400KHz, re-start not support
> clocksource: Switched to clocksource GIC
> NET: Registered protocol family 2
> tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
> TCP established hash table entries: 2048 (order: 1, 8192 bytes)
> TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
> TCP: Hash tables configured (established 2048 bind 2048)
> UDP hash table entries: 256 (order: 1, 8192 bytes)
> UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
> NET: Registered protocol family 1
> Trying to unpack rootfs image as initramfs...
> rootfs image is not initramfs (invalid magic at start of compressed archive); looks like an initrd
> Freeing initrd memory: 16524K
> Initialise system trusted keyrings
> workingset: timestamp_bits=30 max_order=16 bucket_order=0
> squashfs: version 4.0 (2009/01/31) Phillip Lougher
> random: fast init done
> Key type asymmetric registered
> Asymmetric key parser 'x509' registered
> Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
> mt7621_gpio 1e000600.gpio: registering 32 gpios
> mt7621_gpio 1e000600.gpio: registering 32 gpios
> mt7621_gpio 1e000600.gpio: registering 32 gpios
> Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
> printk: console [ttyS0] disabled
> 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 18, base_baud = 3125000) is a 16550A
> printk: console [ttyS0] enabled
> printk: console [ttyS0] enabled
> printk: bootconsole [early0] disabled
> printk: bootconsole [early0] disabled
> 1e000d00.uartlite: ttyS1 at MMIO 0x1e000d00 (irq = 19, base_baud = 3125000) is a 16550A
> ledman: Copyright (C) SnapGear, 2000-2010.
> ledman: registered ERASE switch on IRQ28
> snapdog: HW/SW watchdog timer for SnapGear/Others
> cacheinfo: Failed to find cpu0 device node
> cacheinfo: Unable to detect cache hierarchy for CPU 0
> brd: module loaded
> mt7621-nand: NAND register bank at 0xbe003000
> mt7621-nand: NAND ECC register bank at 0xbe003800
> nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xdc
> nand: Micron NAND 512MiB 3,3V 8-bit
> nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
> nand: ecc bit: 4, spare_per_sector: 16
> Bad block table found at page 262080, version 0x01
> Bad block table found at page 262016, version 0x01
> 5 fixed-partitions partitions found on MTD device MT7621-NAND
> Creating 5 MTD partitions on "MT7621-NAND":
> 0x000000000000-0x000000200000 : "u-boot"
> 0x000000200000-0x000000300000 : "u-boot-env"
> 0x000000300000-0x000000500000 : "log"
> 0x000000500000-0x000020000000 : "flash"
> 0x000000000000-0x000020000000 : "all"
> libphy: Fixed MDIO Bus: probed
> tun: Universal TUN/TAP device driver, 1.6
> libphy: mdio: probed
> mtk_soc_eth 1e100000.ethernet: generated random MAC address 8a:8c:8b:24:60:92
> mtk_soc_eth 1e100000.ethernet: connected mac 0 to PHY at fixed-0:00 [uid=00000000, driver=Generic PHY]
> mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21
> PPP generic driver version 2.4.2
> PPP BSD Compression module registered
> PPP Deflate Compression module registered
> PPP MPPE Compression module registered
> NET: Registered protocol family 24
> SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256).
> CSLIP: code copyright 1989 Regents of the University of California.
> usbcore: registered new interface driver ar5523
> usbcore: registered new interface driver asix
> usbcore: registered new interface driver ax88179_178a
> usbcore: registered new interface driver cdc_ether
> usbcore: registered new interface driver cdc_eem
> usbcore: registered new interface driver rndis_host
> usbcore: registered new interface driver cdc_subset
> usbcore: registered new interface driver cdc_ncm
> usbcore: registered new interface driver qmi_wwan
> usbcore: registered new interface driver cdc_mbim
> ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
> ehci-pci: EHCI PCI platform driver
> ehci-platform: EHCI generic platform driver
> ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
> ohci-pci: OHCI PCI platform driver
> xhci-mtk 1e1c0000.xhci: xHCI Host Controller
> xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
> xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000210010
> xhci-mtk 1e1c0000.xhci: irq 20, io mem 0x1e1c0000
> usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.01
> usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
> usb usb1: Product: xHCI Host Controller
> usb usb1: Manufacturer: Linux 5.1.0-ac0 xhci-hcd
> usb usb1: SerialNumber: 1e1c0000.xhci
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 2 ports detected
> xhci-mtk 1e1c0000.xhci: xHCI Host Controller
> xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
> xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed
> usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
> usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.01
> usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
> usb usb2: Product: xHCI Host Controller
> usb usb2: Manufacturer: Linux 5.1.0-ac0 xhci-hcd
> usb usb2: SerialNumber: 1e1c0000.xhci
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 1 port detected
> usbcore: registered new interface driver cdc_acm
> cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
> usbcore: registered new interface driver cdc_wdm
> usbcore: registered new interface driver usb-storage
> usbcore: registered new interface driver usbserial_generic
> usbserial: USB Serial support registered for generic
> usbcore: registered new interface driver ipw
> usbserial: USB Serial support registered for IPWireless converter
> usbcore: registered new interface driver option
> usbserial: USB Serial support registered for GSM modem (1-port)
> usbcore: registered new interface driver qcaux
> usbserial: USB Serial support registered for qcaux
> usbcore: registered new interface driver qcserial
> usbserial: USB Serial support registered for Qualcomm USB modem
> usbcore: registered new interface driver quatech2
> usbserial: USB Serial support registered for Quatech 2nd gen USB to Serial Driver
> usbcore: registered new interface driver usb_serial_simple
> usbserial: USB Serial support registered for carelink
> usbserial: USB Serial support registered for zio
> usbserial: USB Serial support registered for funsoft
> usbserial: USB Serial support registered for flashloader
> usbserial: USB Serial support registered for google
> usbserial: USB Serial support registered for libtransistor
> usbserial: USB Serial support registered for vivopay
> usbserial: USB Serial support registered for moto_modem
> usbserial: USB Serial support registered for motorola_tetra
> usbserial: USB Serial support registered for novatel_gps
> usbserial: USB Serial support registered for hp4x
> usbserial: USB Serial support registered for suunto
> usbserial: USB Serial support registered for siemens_mpi
> u32 classifier
> input device check on
> ipip: IPv4 and MPLS over IPv4 tunneling driver
> gre: GRE over IPv4 demultiplexor driver
> ip_gre: GRE over IPv4 tunneling driver
> Initializing XFRM netlink socket
> NET: Registered protocol family 10
> Segment Routing with IPv6
> sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
> NET: Registered protocol family 17
> NET: Registered protocol family 15
> 8021q: 802.1Q VLAN Support v1.8
> Loading compiled-in X.509 certificates
> mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
> mt7621-pci 1e140000.pcie: Port 0 N_FTS = 1b102800
> mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
> mt7621-pci 1e140000.pcie: Port 1 N_FTS = 1b102800
> mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
> mt7621-pci 1e140000.pcie: Port 2 N_FTS = 1b102800
> mt7621-pci 1e140000.pcie: pcie0 no card, disable it (RST & CLK)
> mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK)
> mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
>
> [HUNG]
>
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
