Hi Sergio,
On 31/5/19 10:37 pm, Sergio Paracuellos wrote:
On Thu, May 30, 2019 at 3:46 AM Greg Ungerer <gerg@xxxxxxxxxx> wrote:
On 30/5/19 10:44 am, Greg Ungerer wrote:
On 29/5/19 6:08 pm, Sergio Paracuellos wrote:
[snip]
I have added gpio consumer stuff and reorder a bit the code to be more
similar to 4.20.
I attach the patch. I have not try it to compile it, because my normal
environment is in another
computer and I am in the middle of moving from my current house and
don't have access to it, sorry.
So, please try this and let's see what happens.
No problem, thanks for the patch.
Unfortunately always locks up on kernel boot:
...
mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
mt7621-pci 1e140000.pcie: Port 454043648 N_FTS = 0
mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
mt7621-pci 1e140000.pcie: Port 454043648 N_FTS = 1
mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
mt7621-pci 1e140000.pcie: Port 454043648 N_FTS = 2
mt7621-pci 1e140000.pcie: pcie0 no card, disable it (RST & CLK)
mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK)
mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
That was original linux-5.1 patched with your attached patch.
I'll try and dig down into that further today and get some
feedback on where it is failing.
The first problem I see is that the GPIO MODE register bits for
PERST_MODE are set to 00, so in "PCIe Reset" mode. If I hack in
a register update for that with:
/* Force PERST PCIe reset into GPIO mode */
*(unsigned int *)(0xbe000060) |= BIT(10);
I have set GPIO mode for this in the new attached patch.
I do that at the start of mt7621_pcie_init_ports(). With that in
place I get further:
mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
mt7621-pci 1e140000.pcie: Port 454043648 N_FTS = 0
mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
mt7621-pci 1e140000.pcie: Port 454043648 N_FTS = 1
mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
mt7621-pci 1e140000.pcie: Port 454043648 N_FTS = 2
mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK)
mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
mt7621-pci 1e140000.pcie: PCIE0 enabled
mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [io 0xffffffff]
pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
pci_bus 0000:00: root bus resource [bus 00-ff]
pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
It hangs there...
I had review the boot order is working for you in version 4.20 and the
order with the new patch applied. There were
only one difference, the place where interrupt bits are set. I have
changed that also in the new attached patch.
For me, the order now and how the different boot steps are being done
in v4.20 are the same.
One other thing I don't really understand why is needed but is in the
v4.20 code are this two lines:
pcie_write(pcie, 0xffffffff, RALINK_PCI_MEMBASE);
pcie_write(pcie, RALINK_PCI_IO_MAP_BASE, RALINK_PCI_IOBASE);
These are added also in the current patch.
Tried out this latest patch. Unfortunately no good news.
Boot gets through the PCI bus scan, but does not find any devices:
mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
mt7621-pci 1e140000.pcie: Port 454043648 N_FTS = 0
mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
mt7621-pci 1e140000.pcie: Port 454043648 N_FTS = 1
mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
mt7621-pci 1e140000.pcie: Port 454043648 N_FTS = 2
mt7621-pci 1e140000.pcie: pcie0 no card, disable it (RST & CLK)
mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK)
mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
mt7621-pci 1e140000.pcie: Nothing is connected in virtual bridges. Exiting...
And now in the completely weird and un-expected department the boot
continues on and appears to hang for me when it tries to attach a
UBI NAND flash partition. It hangs there for about a minute or so
and then dumps complaing about flash problems:
ubi0: attaching mtd3
ubi0: scanning is finished
ubi0: empty MTD device detected
ubi0 warning: do_sync_erase: error -5 while erasing PEB 0, retry
ubi0 warning: do_sync_erase: error -5 while erasing PEB 0, retry
ubi0 warning: do_sync_erase: error -5 while erasing PEB 0, retry
ubi0 error: do_sync_erase: cannot erase PEB 0, error -5
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 5.1.0-ac0 #59
Stack : 000000f0 00000000 00000000 808e0000 8ebf2000 80070584 808285b8 0000000b
00000038 00000000 80827e00 8fc23b1c 80870000 00000001 8fc23ab0 aeddef9b
00000000 00000000 80920000 00000000 00000000 808e7693 000000f1 00000000
203a6d6d 00000000 00000000 00000000 80870000 00000000 00000000 8080a01c
00000000 80870000 8ebf1014 8ebd2000 00000018 80361d24 00000004 808e0004
...
Call Trace:
[<8000cfc0>] show_stack+0x94/0x12c
[<806e553c>] dump_stack+0x8c/0xd0
[<803c73c8>] do_sync_erase+0xf4/0x208
[<803c7694>] ubi_io_sync_erase+0x1b8/0x304
[<803cbc90>] ubi_early_get_peb+0x148/0x1dc
[<803ba930>] create_vtbl+0xb4/0x29c
[<803bafc8>] ubi_read_volume_table+0x27c/0xae4
[<803cc294>] ubi_attach+0x570/0x15dc
[<803bf2a0>] ubi_attach_mtd_dev+0x5b0/0xbec
[<808b0488>] ubi_init+0x1c0/0x274
[<800015f4>] do_one_initcall+0x50/0x1ac
[<80897e98>] kernel_init_freeable+0x184/0x26c
[<807035b4>] kernel_init+0x14/0x110
[<800071f8>] ret_from_kernel_thread+0x14/0x1c
I tried booting and running this several times, I always get the same
long hang and dump from USB/NAND. If I copy in the one linux-4.20
file, drivers/staging/mt7621-pci/pci-mt7621.c, then the system
boots, scans and finds PCI devices, and does not hang/dump on
UBI/NAND flash setup.
I'll try and dig into it some time today and get you some feedback.
Regards
Greg
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
