Just an update. I think I have wvdial and its related programs like
wvstreams installed. I re-executed the commands you suggested earlier.
Here are the results.
[root@localhost agrsm06pci-2.1.80~20100106]# ./agrsm-test
Found drivers for boot kernel 2.6.32.12-pclos1.bfs at:
find: paths must precede expression: agrserial.ko
Usage: find [-H] [-L] [-P] [-Olevel] [-D
help|tree|search|stat|rates|opt|exec] [path...] [expression]
Loading drivers:
Checking for utility wvdialconf
Found /usr/bin/wvdialconf, preparing to run:
wvdialconf /etc/wvdial.conf
Modem Port Scan<*1>: Scanning ttyS0 first, /dev/modem is a link to it.
Modem Port Scan<*1>: S0 S1 S2 S3
A reboot may be necessary before modem detection through:
sudo modprobe agrserial
Which will load agrmodem, agrserial and create the symbolic link needed for:
sudo wvdialconf
The installation record has been written to ./agrsm-test.txt
<<end of agrsm-test>>
I assume the modprobe command noted in these results is the same as the
one you mentioned earlier, so I ignored that. So I manually tried the
wvdial command listed with these results:
[root@localhost agrsm06pci-2.1.80~20100106]# wvdialconf /etc/wvdial.conf
Editing `/etc/wvdial.conf'.
Scanning your serial ports for a modem.
Modem Port Scan<*1>: Scanning ttyS0 first, /dev/modem is a link to it.
Modem Port Scan<*1>: S0 S1 S2 S3
Sorry, no modem was detected! Is it in use by another program?
Did you configure it properly with setserial?
<<end of wvdialconf>>
I did review the available help on the setserial command, but at this
point, I have no idea what the proper command should be.
Thanks.
On 05/25/2010 10:57 AM, mwl wrote:-ex
Here are the results of the commands you suggested.
# modprobe agrmodem
# modprobe agrserial
# ./agrsm-test
Found drivers for boot kernel 2.6.32.12-pclos1.bfs at:
find: paths must precede expression: agrserial.ko
Usage: find [-H] [-L] [-P] [-Olevel] [-D
help|tree|search|stat|rates|opt|exec] [path...] [expression]
Loading drivers:
Checking for utility wvdialconf
Utility wvdialconf not found
The installation record has been written to ./agrsm-test.txt
<<end>>
I rebooted and rechecked with
# modprobe -l agr*
kernel/drivers/extra/agrserial.ko.gz
kernel/drivers/extra/agrmodem.ko.gz
extra/agrserial.ko
extra/agrmodem.ko
I know you prefer to test with wvdial, but because I am still having
problems getting wvdial and wvstreams installed, I tried dialing out
with KPPP and get the same message about the modem being busy. I am
trying to connect with the dev/modem device. I looked thru the list
of available modems trying to find one that used AGR or something
similar, but there was none.
Thanks for your continued help.
On 05/24/2010 06:52 PM, Marvin Stodolsky wrote:
Martin,
Loading will be OK, I expect, if you as root,
# modprobe agrmodem
# modprobe agrserial
Then run
# ./agrsm-test
The problem which we can fix later is that the /etc/modprobe file/line
for pre-loading agrmodem before agrserial is not yet present.
We can fix this later.
Test and report back.
MarvS
On Mon, May 24, 2010 at 10:08 AM, mwl<mossianin_lbcmi@xxxxxxxxxx>
wrote:
The results of the find show the following:
/lib/modules/2.6.32.12-pclos1.bfs/extra/agrmodem.ko
/lib/modules/2.6.32.12-pclos1.bfs/extra/agrserial.ko
Thanks.
On 05/23/2010 05:09 PM, Marvin Stodolsky wrote:
Martin,
Again check where they installed to with:
$ find /lib/modules -name agr*.ko
MarvS
On Sun, May 23, 2010 at 6:32 PM, mwl<mossianin_lbcmi@xxxxxxxxxx>
wrote:
The following is the results of the install sequence. If I am
understanding
correctly, it looks like the driver installed.
[agrsm06pci-2.1.80~20100106]# make clean
make -C /lib/modules/2.6.32.12-pclos1.bfs/build
M=/usr/src/agrsm06pci-2.1.80~20100106 clean
make[1]: Entering directory
`/usr/src/kernel-devel-2.6.32.12-pclos1.bfs'
CLEAN /usr/src/agrsm06pci-2.1.80~20100106/.tmp_versions
CLEAN /usr/src/agrsm06pci-2.1.80~20100106/Module.symvers
/usr/src/agrsm06pci-2.1.80~20100106/modules.order
make[1]: Leaving directory
`/usr/src/kernel-devel-2.6.32.12-pclos1.bfs'
[agrsm06pci-2.1.80~20100106]# make
make -C /lib/modules/2.6.32.12-pclos1.bfs/build
M=/usr/src/agrsm06pci-2.1.80~20100106 modules
make[1]: Entering directory
`/usr/src/kernel-devel-2.6.32.12-pclos1.bfs'
CC [M] /usr/src/agrsm06pci-2.1.80~20100106/agrsoftmodem.o
/usr/src/agrsm06pci-2.1.80~20100106/agrsoftmodem.c: In function
‘agr_pci_find_device’:
/usr/src/agrsm06pci-2.1.80~20100106/agrsoftmodem.c:364: warning:
ignoring
return value of ‘pci_enable_device’, declared with attribute
warn_unused_result
/usr/src/agrsm06pci-2.1.80~20100106/agrsoftmodem.c: In function
‘x_linux_dbg_print_crit’:
/usr/src/agrsm06pci-2.1.80~20100106/agrsoftmodem.c:349: warning: the
frame
size of 1540 bytes is larger than 1024 bytes
/usr/src/agrsm06pci-2.1.80~20100106/agrsoftmodem.c: In function
‘x_linux_dbg_print’:
/usr/src/agrsm06pci-2.1.80~20100106/agrsoftmodem.c:337: warning: the
frame
size of 1540 bytes is larger than 1024 bytes
SHIPPED /usr/src/agrsm06pci-2.1.80~20100106/agrmodemlib.o
CC [M] /usr/src/agrsm06pci-2.1.80~20100106/hda.o
CC [M] /usr/src/agrsm06pci-2.1.80~20100106/serial26.o
LD [M] /usr/src/agrsm06pci-2.1.80~20100106/agrmodem.o
LD [M] /usr/src/agrsm06pci-2.1.80~20100106/agrserial.o
Building modules, stage 2.
MODPOST 2 modules
WARNING: could not find
/usr/src/agrsm06pci-2.1.80~20100106/.agrmodemlib.o.cmd for
/usr/src/agrsm06pci-2.1.80~20100106/agrmodemlib.o
CC /usr/src/agrsm06pci-2.1.80~20100106/agrmodem.mod.o
LD [M] /usr/src/agrsm06pci-2.1.80~20100106/agrmodem.ko
CC /usr/src/agrsm06pci-2.1.80~20100106/agrserial.mod.o
LD [M] /usr/src/agrsm06pci-2.1.80~20100106/agrserial.ko
make[1]: Leaving directory
`/usr/src/kernel-devel-2.6.32.12-pclos1.bfs'
[agrsm06pci-2.1.80~20100106]# make module_install
make: *** No rule to make target `module_install'. Stop.
[root@localhost agrsm06pci-2.1.80~20100106]# make modules_install
make -C /lib/modules/2.6.32.12-pclos1.bfs/build
M=/usr/src/agrsm06pci-2.1.80~20100106 modules_install
make[1]: Entering directory
`/usr/src/kernel-devel-2.6.32.12-pclos1.bfs'
INSTALL /usr/src/agrsm06pci-2.1.80~20100106/agrmodem.ko
INSTALL /usr/src/agrsm06pci-2.1.80~20100106/agrserial.ko
DEPMOD 2.6.32.12-pclos1.bfs
make[1]: Leaving directory
`/usr/src/kernel-devel-2.6.32.12-pclos1.bfs'
<<end of install>>
Based on earlier instructions, I then tried the agrsm-test as
follows:
[agrsm06pci-2.1.80~20100106]# ./agrsm-test
Found drivers for boot kernel 2.6.32.12-pclos1.bfs at:
find: paths must precede expression: agrserial.ko
Usage: find [-H] [-L] [-P] [-Olevel] [-D
help|tree|search|stat|rates|opt|exec] [path...] [expression]
Loading drivers:
FATAL: Error inserting agrserial
(/lib/modules/2.6.32.12-pclos1.bfs/extra/agrserial.ko): No such
device
Checking for utility wvdialconf
Utility wvdialconf not found
The installation record has been written to ./agrsm-test.txt
<<end of agrsm-test>>
When I noticed the FATAL, I did find the file(device?) at the
location
specified in the error message, so now I am stumped (again).
Because the test noted that wvdial did not exist, I tried using
KPPP to
connect and all I get is a message about the modem being busy.
I am trying to get my hands on wvdial, but that requires
wvstreams, which
will not install for some reason. So, I thought I would pass
along what
I
can in the hopes that there is enough there to help solve the
problem.
Thanks.
On 05/23/2010 02:54 PM, Marvin Stodolsky wrote:
Martin
Use agrsm06pci-2.1.80-20106
After the
# make clean
# make
read the Makefile with
# more Makefile
You will thus see that the command needed is:
# make modules_install
Why the LSI maintainer choose this variant is obscure.
MarvS
On Sun, May 23, 2010 at 4:32 PM, mwl<mossianin_lbcmi@xxxxxxxxxx>
wrote:
I apologize for the slowness of my responses lately. I have been
waiting
for PCLinux to release a more current kernel to the ones that we
have
been
discussing. Now, they have the 2.6.32 kernel and I have
upgraded the
problem machine to that kernel and have been re-attempting to
get this
Agere
11c1:0630 modem working.
I started off with what I believe is the most recent driver
(agrsm06pci-2.1.80-20100106) and executed the following commands
from
the
usr/src directory
[agrsm06pci-2.1.80~20100106]#make clean
make -C /lib/modules/2.6.32.12-pclos1.bfs/build
M=/usr/src/agrsm06pci-2.1.80~20100106 clean
make[1]: Entering directory
`/usr/src/kernel-devel-2.6.32.12-pclos1.bfs'
CLEAN /usr/src/agrsm06pci-2.1.80~20100106/.tmp_versions
CLEAN /usr/src/agrsm06pci-2.1.80~20100106/Module.symvers
/usr/src/agrsm06pci-2.1.80~20100106/Module.markers
/usr/src/agrsm06pci-2.1.80~20100106/modules.order
make[1]: Leaving directory
`/usr/src/kernel-devel-2.6.32.12-pclos1.bfs'
[agrsm06pci-2.1.80~20100106]# make
make -C /lib/modules/2.6.32.12-pclos1.bfs/build
M=/usr/src/agrsm06pci-2.1.80~20100106 modules
make[1]: Entering directory
`/usr/src/kernel-devel-2.6.32.12-pclos1.bfs'
CC [M] /usr/src/agrsm06pci-2.1.80~20100106/agrsoftmodem.o
/usr/src/agrsm06pci-2.1.80~20100106/agrsoftmodem.c: In function
‘agr_pci_find_device’:
/usr/src/agrsm06pci-2.1.80~20100106/agrsoftmodem.c:364: warning:
ignoring
return value of ‘pci_enable_device’, declared with attribute
warn_unused_result
/usr/src/agrsm06pci-2.1.80~20100106/agrsoftmodem.c: In function
‘x_linux_dbg_print_crit’:
/usr/src/agrsm06pci-2.1.80~20100106/agrsoftmodem.c:349: warning:
the
frame
size of 1540 bytes is larger than 1024 bytes
/usr/src/agrsm06pci-2.1.80~20100106/agrsoftmodem.c: In function
‘x_linux_dbg_print’:
/usr/src/agrsm06pci-2.1.80~20100106/agrsoftmodem.c:337: warning:
the
frame
size of 1540 bytes is larger than 1024 bytes
SHIPPED /usr/src/agrsm06pci-2.1.80~20100106/agrmodemlib.o
CC [M] /usr/src/agrsm06pci-2.1.80~20100106/hda.o
CC [M] /usr/src/agrsm06pci-2.1.80~20100106/serial26.o
LD [M] /usr/src/agrsm06pci-2.1.80~20100106/agrmodem.o
LD [M] /usr/src/agrsm06pci-2.1.80~20100106/agrserial.o
Building modules, stage 2.
MODPOST 2 modules
WARNING: could not find
/usr/src/agrsm06pci-2.1.80~20100106/.agrmodemlib.o.cmd for
/usr/src/agrsm06pci-2.1.80~20100106/agrmodemlib.o
CC /usr/src/agrsm06pci-2.1.80~20100106/agrmodem.mod.o
LD [M] /usr/src/agrsm06pci-2.1.80~20100106/agrmodem.ko
CC /usr/src/agrsm06pci-2.1.80~20100106/agrserial.mod.o
LD [M] /usr/src/agrsm06pci-2.1.80~20100106/agrserial.ko
make[1]: Leaving directory
`/usr/src/kernel-devel-2.6.32.12-pclos1.bfs'
[agrsm06pci-2.1.80~20100106]# make install
make: *** No rule to make target `install'. Stop.
I also went back to the agrsm06pci-2.1.80-20090825 version of the
driver
with the following results.
make clean
rm -f *.a
rm -f *~
rm -f agrmodem.o
rm -f agrmodem.ko
rm -f agrmodem.mod.o
rm -f agrmodem.mod.c
rm -f agrserial.o
rm -f agrserial.ko
rm -f agrserial.mod.o
rm -f agrserial.mod.c
rm -f agrsoftmodem.o
rm -f serial26.o
rm -f HDA.o
rm -f hda.o
rm -f modules.order
rm -f Module.symvers
rm -f Module.markers
[agrsm06pci-2.1.80~20090825]# make
Run "make install" to install Agere Systems Soft Modem on your
system.
Run "make uninstall" to remove a previously installed modem.
[agrsm06pci-2.1.80~20090825]# make install
./agrinst
Installing Agere Softmodem driver version 2.1.80-Red Flag NE 5.0
some files needed for installation are missing
Any help would be appreciated.
Thanks.
