Hi Marvin, the modem run perfectly: ciornj@deskubu904:~$ sudo wvdialconf wvtest [sudo] password for ciornj: Editing `wvtest'. Scanning your serial ports for a modem. ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up. ttyS1<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud ttyS1<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud ttyS1<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up. Modem Port Scan<*1>: S2 S3 WvModem<*1>: Cannot get information for serial port. ttySL0<*1>: ATQ0 V1 E1 -- OK ttySL0<*1>: ATQ0 V1 E1 Z -- OK ttySL0<*1>: ATQ0 V1 E1 S0=0 -- OK ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK ttySL0<*1>: Modem Identifier: ATI -- SmartLink Soft Modem ttySL0<*1>: Speed 4800: AT -- OK ttySL0<*1>: Speed 9600: AT -- OK ttySL0<*1>: Speed 19200: AT -- OK ttySL0<*1>: Speed 38400: AT -- OK ttySL0<*1>: Speed 57600: AT -- OK ttySL0<*1>: Speed 115200: AT -- OK ttySL0<*1>: Speed 230400: AT -- OK ttySL0<*1>: Speed 460800: AT -- OK ttySL0<*1>: Max speed is 460800; that should be safe. ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK Found a modem on /dev/ttySL0. wvtest<Warn>: Can't open 'wvtest' for reading: No such file or directory wvtest<Warn>: ...starting with blank configuration. Modem configuration written to wvtest. ttySL0<Info>: Speed 460800; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0" ciornj@deskubu904:~$ wvdial --> WvDial: Internet dialer version 1.60 --> Cannot get information for serial port. --> Initializing modem. --> Sending: ATZ ATZ OK --> Sending: ATQ0 V1 X3 E1 S0=0 &C1 &D2 +FCLASS=0 ATQ0 V1 X3 E1 S0=0 &C1 &D2 +FCLASS=0 OK --> Modem initialized. --> Sending: ATDTXXXXXXXXXXXXX --> Waiting for carrier. ATDTXXXXXXXXXXXXXXX ^CCaught signal 2: Attempting to exit gracefully... --> Disconnecting at Thu Mar 4 08:16:39 2010 ciornj@deskubu904:~$ Thank you very much Arturo 2010/3/4 Marvin Stodolsky <marvin.stodolsky@xxxxxxxxx>: > Arturo > > Unpack the attached: > $ gunzip sl*.gz > Then > $ sudo cp sl-modem-daemon.conf /etc/modprobe.d/ > This will provide for autoloading of ungrab-winmodem. > > Reboot and the modem should be setup automatically > Test with: > $ lsmod | grep ungrab > $ ls -l /dev/ttySL0 /dev/slamr0 > to check ports. > > $ sudo wvdialconf wvtest > should now find the modem > > MarvS > > On Wed, Mar 3, 2010 at 3:04 PM, Arturo Neri <ciornjeja@xxxxxxxxx> wrote: >> Hi Marv, >> after removed sl-modem-sources and daemon without shutdown pc I made: >> ciornj@deskubu904:~$ sudo apt-get install sl-modem-source >> [sudo] password for ciornj: >> Lettura della lista dei pacchetti in corso... Fatto >> Generazione dell'albero delle dipendenze in corso >> Lettura informazioni sullo stato... Fatto >> I seguenti pacchetti NUOVI (NEW) saranno installati: >> sl-modem-source >> 0 aggiornati, 1 installati, 0 da rimuovere e 0 non aggiornati. >> È necessario prendere 0B/498kB di archivi. >> Dopo quest'operazione, verranno occupati 1167kB di spazio su disco. >> Selezionato il pacchetto sl-modem-source, che non lo era. >> (Lettura del database ... 200955 file e directory attualmente installati.) >> Spacchetto sl-modem-source (da >> .../sl-modem-source_2.9.11~20080817-3ubuntu2_i386.deb) ... >> Configuro sl-modem-source (2.9.11~20080817-3ubuntu2) ... >> Adding Module to DKMS build system >> Doing initial module build >> Installing initial module >> Done.ciornj@deskubu904:~$ sudo slmodemd -c ITALY /dev/slamr0 >> error: mdm setup: cannot stat `/dev/slamr0': No such file or directory >> error: cannot setup device `/dev/slamr0' >> ciornj@deskubu904:~$ dmesg | tail -15 >> [ 21.617661] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 >> [ 21.617667] Bluetooth: BNEP filters: protocol multicast >> [ 21.640490] Bridge firewalling registered >> [ 26.839640] skge eth0: enabling interface >> [ 26.843100] ADDRCONF(NETDEV_UP): eth0: link is not ready >> [ 29.847902] skge eth0: Link is up at 100 Mbps, full duplex, flow control both >> [ 29.848117] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready >> [ 40.104010] eth0: no IPv6 routers present >> [ 170.722312] device 10b9:5459 is grabbed by driver serial: try to release >> [ 170.724172] serial 0000:02:02.0: PCI INT A disabled >> [ 223.714548] slamr: SmartLink AMRMO modem. >> [ 223.714644] slamr: probe 10b9:5459 SL1800 card... >> [ 223.714662] slamr 0000:02:02.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 >> [ 223.716822] slamr: mc97 codec is SIL26 >> [ 223.717071] slamr: slamr0 is SL1800 card. >> ciornj@deskubu904:~$ >> >> >> ciornj@deskubu904:~$ sudo apt-get install sl-modem-daemon >> Lettura della lista dei pacchetti in corso... Fatto >> Generazione dell'albero delle dipendenze in corso >> Lettura informazioni sullo stato... Fatto >> I seguenti pacchetti NUOVI (NEW) saranno installati: >> sl-modem-daemon >> 0 aggiornati, 1 installati, 0 da rimuovere e 0 non aggiornati. >> È necessario prendere 0B/514kB di archivi. >> Dopo quest'operazione, verranno occupati 1147kB di spazio su disco. >> Preconfigurazione dei pacchetti in corso >> Selezionato il pacchetto sl-modem-daemon, che non lo era. >> (Lettura del database ... 200996 file e directory attualmente installati.) >> Spacchetto sl-modem-daemon (da >> .../sl-modem-daemon_2.9.11~20080817-3ubuntu2_i386.deb) ... >> Processing triggers for man-db ... >> Configuro sl-modem-daemon (2.9.11~20080817-3ubuntu2) ... >> Attenzione: impossibile accedere alla directory home /var/log/slmodemd >> indicata: Nessun file o directory >> L'utente di sistema «Slmodemd» già esiste. Uscita. >> usermod: nessuna modifica >> Starting SmartLink Modem driver for: slamr0. >> Creating /dev/modem symlink, pointing to: /dev/ttySL0. >> >> ciornj@deskubu904:~$ dmesg | tail -15 >> [18382.704303] option1 ttyUSB3: GSM modem (1-port) converter now >> disconnected from ttyUSB3 >> [18382.704325] option 1-3.4:1.3: device disconnected >> [18382.704562] option1 ttyUSB4: GSM modem (1-port) converter now >> disconnected from ttyUSB4 >> [18382.704584] option 1-3.4:1.4: device disconnected >> [18382.704821] option1 ttyUSB5: GSM modem (1-port) converter now >> disconnected from ttyUSB5 >> [18382.704844] option 1-3.4:1.5: device disconnected >> [18385.064640] usbcore: deregistering interface driver option >> [18385.064688] USB Serial deregistering driver GSM modem (1-port) >> [18385.181436] USB Serial support registered for GSM modem (1-port) >> [18385.181509] usbcore: registered new interface driver option >> [18385.181514] option: v0.7.2:USB Driver for GSM modems >> [18557.178616] slamr: SmartLink AMRMO modem. >> [18557.178648] slamr: device 10b9:5459 is grabbed by another driver >> [18673.677840] device 10b9:5459 is grabbed by driver serial: try to release >> [18673.678951] serial 0000:02:02.0: PCI INT A disabled >> ciornj@deskubu904:~$ >> >> I restart pc and >> ciornj@deskubu904:~$ lsmod >> slamr 435496 0 >> ciornj@deskubu904:~$ dmesg | tail -15 >> [ 17.373406] NFSD: starting 90-second grace period >> [ 19.522396] vboxdrv: Trying to deactivate the NMI watchdog permanently... >> [ 19.522405] vboxdrv: Successfully done. >> [ 19.522409] vboxdrv: Found 2 processor cores. >> [ 19.523048] vboxdrv: fAsync=0 offMin=0x3f0 offMax=0x30f2 >> [ 19.525828] vboxdrv: TSC mode is 'synchronous', kernel timer mode >> is 'normal'. >> [ 19.525837] vboxdrv: Successfully loaded version 3.1.4 (interface >> 0x00100001). >> [ 21.617661] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 >> [ 21.617667] Bluetooth: BNEP filters: protocol multicast >> [ 21.640490] Bridge firewalling registered >> [ 26.839640] skge eth0: enabling interface >> [ 26.843100] ADDRCONF(NETDEV_UP): eth0: link is not ready >> [ 29.847902] skge eth0: Link is up at 100 Mbps, full duplex, flow control both >> [ 29.848117] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready >> [ 40.104010] eth0: no IPv6 routers present >> ciornj@deskubu904:~$ sudo modprobe ungrab-winmodem >> [sudo] password for ciornj: >> ciornj@deskubu904:~$ sudo modprobe -r slamr >> ciornj@deskubu904:~$ lsmod >> Module Size Used by >> ungrab_winmodem 9984 0 >> >> ciornj@deskubu904:~$ sudo modprobe slamr >> ciornj@deskubu904:~$ lsmod >> Module Size Used by >> slamr 435496 0 >> ungrab_winmodem 9984 0 >> >> ciornj@deskubu904:~$ sudo slmodemd -c ITALY /dev/slamr0 >> error: mdm setup: cannot stat `/dev/slamr0': No such file or directory >> error: cannot setup device `/dev/slamr0' >> ciornj@deskubu904:~$ dmesg | tail -15 >> [ 21.617661] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 >> [ 21.617667] Bluetooth: BNEP filters: protocol multicast >> [ 21.640490] Bridge firewalling registered >> [ 26.839640] skge eth0: enabling interface >> [ 26.843100] ADDRCONF(NETDEV_UP): eth0: link is not ready >> [ 29.847902] skge eth0: Link is up at 100 Mbps, full duplex, flow control both >> [ 29.848117] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready >> [ 40.104010] eth0: no IPv6 routers present >> [ 170.722312] device 10b9:5459 is grabbed by driver serial: try to release >> [ 170.724172] serial 0000:02:02.0: PCI INT A disabled >> [ 223.714548] slamr: SmartLink AMRMO modem. >> [ 223.714644] slamr: probe 10b9:5459 SL1800 card... >> [ 223.714662] slamr 0000:02:02.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 >> [ 223.716822] slamr: mc97 codec is SIL26 >> [ 223.717071] slamr: slamr0 is SL1800 card. >> ciornj@deskubu904:~$ >> Thanks very much, >> Arturo >> >> >> >> 2010/3/3 Marvin Stodolsky <marvin.stodolsky@xxxxxxxxx>: >>> Arturo, >>> >>> RE: FATAL: Error inserting ungrab_winmodem >>> (/lib/modules/2.6.28-18-generic/updates/dkms/ungrab-winmodem.ko): >>> Unknown symbol in module, or unknown parameter (see dmesg) >>> ----------------- >>> This is unexpected. Please try reinstalling the sl-modem-source package. >>> $ sudo apt-get remove sl-modem-source >>> and then reinstall. >>> >>> If you get the same error do: >>> $ dmesg | tail -15 >>> and send us the output. >>> >>> The should be function under 2.6.28-18-generic >>> >>> MarvS >>> >>> MarvS >>> >>> >>> On Tue, Mar 2, 2010 at 1:05 PM, Arturo Neri <ciornjeja@xxxxxxxxx> wrote: >>>> In a hard disk I have Ubuntu 8.10 kernel 2.6.27-14 and there modem run well. >>>> I installed the new release 9.04 in a new HD and before delete old I >>>> tried to install modules for modem into new. >>>> But I haven't chance. I installed: >>>> libasound2-dev >>>> sl-modem-source >>>> sl-modem-daemon >>>> but when I read lsmod there is only slamr module not ungrab-winmodem. >>>> I tried: >>>> ciornj@deskubu904:~$ sudo modprobe ungrab-winmodem debug=3 >>>> [sudo] password for ciornj: >>>> FATAL: Error inserting ungrab_winmodem >>>> (/lib/modules/2.6.28-18-generic/updates/dkms/ungrab-winmodem.ko): >>>> Unknown symbol in module, or unknown parameter (see dmesg) >>>> ciornj@deskubu904:~$ dmesg | grep ungrab-winmodem >>>> ciornj@deskubu904:~$ dmesg | grep slamr >>>> [ 14.767920] slamr: module license 'Smart Link Ltd.' taints kernel. >>>> [ 14.776133] slamr: SmartLink AMRMO modem. >>>> [ 14.776166] slamr: device 10b9:5459 is grabbed by another driver >>>> Can anyone help me? >>>> Or I must stay all time with old release. >>>> Arturo >>>> >>> >> >
