Am I understanding that the agrsm06pci-2.1.80-20100106 will work with my
2.5.26 kernel? If I understand correctly, your test was with the 2.6.33
kernel. Can you clarify?
Thanks.
Antonio Olivares wrote:
Dear Nikolay, Marv & et all,
I have tried the agrsm code that worked in 11c1:0620 agere modem on an
11c1:0630 modem that came on emachines that I had, and it worked!!! I
am reporting success and thanking Nikolay and others who have worked
on the Agere LSI code.
Ran, make clean, make install(failed) and then used ./agrinstall to
install the modem drivers :
olivares@darkstar:~/Downloads$ cd agrsm06pci-2.1.80~20100106
olivares@darkstar:~/Downloads/agrsm06pci-2.1.80~20100106$ make clean
make -C /lib/modules/2.6.33-smp/build
M=/home/olivares/Downloads/agrsm06pci-2.1.80~20100106 clean
make[1]: Entering directory `/usr/src/linux-2.6.33'
CLEAN /home/olivares/Downloads/agrsm06pci-2.1.80~20100106/.tmp_versions
CLEAN /home/olivares/Downloads/agrsm06pci-2.1.80~20100106/Module.symvers
/home/olivares/Downloads/agrsm06pci-2.1.80~20100106/modules.order
make[1]: Leaving directory `/usr/src/linux-2.6.33'
olivares@darkstar:~/Downloads/agrsm06pci-2.1.80~20100106$ make all
make: *** No rule to make target `all'. Stop.
olivares@darkstar:~/Downloads/agrsm06pci-2.1.80~20100106$ make
make -C /lib/modules/2.6.33-smp/build
M=/home/olivares/Downloads/agrsm06pci-2.1.80~20100106 modules
make[1]: Entering directory `/usr/src/linux-2.6.33'
CC [M] /home/olivares/Downloads/agrsm06pci-2.1.80~20100106/agrsoftmodem.o
/home/olivares/Downloads/agrsm06pci-2.1.80~20100106/agrsoftmodem.c: In
function 'agr_pci_find_device':
/home/olivares/Downloads/agrsm06pci-2.1.80~20100106/agrsoftmodem.c:364:
warning: ignoring return value of 'pci_enable_device', declared with
attribute warn_unused_result
SHIPPED /home/olivares/Downloads/agrsm06pci-2.1.80~20100106/agrmodemlib.o
CC [M] /home/olivares/Downloads/agrsm06pci-2.1.80~20100106/hda.o
CC [M] /home/olivares/Downloads/agrsm06pci-2.1.80~20100106/serial26.o
LD [M] /home/olivares/Downloads/agrsm06pci-2.1.80~20100106/agrmodem.o
LD [M] /home/olivares/Downloads/agrsm06pci-2.1.80~20100106/agrserial.o
Building modules, stage 2.
MODPOST 2 modules
CC /home/olivares/Downloads/agrsm06pci-2.1.80~20100106/agrmodem.mod.o
LD [M] /home/olivares/Downloads/agrsm06pci-2.1.80~20100106/agrmodem.ko
CC /home/olivares/Downloads/agrsm06pci-2.1.80~20100106/agrserial.mod.o
LD [M] /home/olivares/Downloads/agrsm06pci-2.1.80~20100106/agrserial.ko
make[1]: Leaving directory `/usr/src/linux-2.6.33'
olivares@darkstar:~/Downloads/agrsm06pci-2.1.80~20100106$ ls
1stReadme.txt agrinst* agrserial.mod.c dkms.conf
8250.h agrmodem.h agrserial.mod.o hda.c
AgereMdmDaemon* agrmodem.ko agrserial.o hda.o
Kbuild agrmodem.mod.c agrsm-test* hda_codec.h
LICENSE agrmodem.mod.o agrsm.conf linuxif.h
Makefile agrmodem.o agrsoftmodem.c modules.order
Module.symvers agrmodemlib.o agrsoftmodem.o postinst*
agr_auxinst* agrmodemlib.o_shipped agruninst* serial26.c
agr_softmodem* agrserial.ko config.h serial26.o
olivares@darkstar:~/Downloads/agrsm06pci-2.1.80~20100106$ make install
make: *** No rule to make target `install'. Stop.
olivares@darkstar:~/Downloads/agrsm06pci-2.1.80~20100106$ ./agrinst
returned a warning that README was not there :(, but other than that SUCCESS!!
root@darkstar:~# cat /etc/slackware-version
Slackware 13.0.0.0.0
root@darkstar:~# uname -r
2.6.33-smp
root@darkstar:~# dmesg | grep 'agr*'
ftrace: allocating 32587 entries in 64 pages
highmem bounce pool size: 64 pages
NTFS driver 2.1.29 [Flags: R/W].
SGI XFS Quota Management subsystem
vesafb: mode is 1024x768x8, linelength=1024, pages=3
GDT-HA: Storage RAID Controller Driver. Version: 3.05
3ware Storage Controller device driver for Linux v1.26.02.002.
3ware 9000 Storage Controller device driver for Linux v2.26.02.013.
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
scsi8 : usb-storage 1-8:1.0
ACPI Warning for \_TZ_.THRM._PSL: Return Package type mismatch at
index 0 - found [NULL Object Descriptor], expected Reference
(20091214/nspredef-1040)
ACPI: Expecting a [Reference] package element, found type 0
Linux agpgart interface v0.103
agrmodem: module license 'Proprietary' taints kernel.
Loading module Agere Modem Controller driver version 2.1.80-Red Flag
NE 5.0 (2007-10-1)
Loading module Agere Modem Interface driver version 2.1.80.0Red Flag
5.0 NE (2007-10-01)
root@darkstar:~# /etc/rc.d/rc.agr_softmodem start
Starting Agere Soft Modem
part of dmesg:
agrmodem: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
* Hello Agere Driver PCIe **
ACPI: PCI Interrupt Link [APC6] enabled at IRQ 16
pci 0000:03:00.0: PCI INT A -> Link[APC6] -> GSI 16 (level, low) -> IRQ 16
get irq 10
Loading module Agere Modem Controller driver version 2.1.80-Red Flag
NE 5.0 (2007-10-1)
ttyAGS3 at I/O 0x400 (irq = 3) is a AgereModem
Loading module Agere Modem Interface driver version 2.1.80.0Red Flag
5.0 NE (2007-10-01)
==> codecType = 0x34
App PID = 2022
Martin,
Modem does work so you can safely install newer kernel(s) that may
come with PCLinuxOS or other distribution of your choice :)
Regards,
Antonio
Only plain text email is forwarded by the Discuss@xxxxxxxxxxxxx List Server,
as HTML can contain viruses. Use as the email Subject Line:
YourName, YourCountry
Welcome to kernel 2.6.33-smp
With this Subject Line cogent experts will be alerted, and useful
case names left in the Archive.
YourCountry will enable Country specific guidance. Linux experts in
YourCountry
can be found through: http://www.linux.org/groups/index.html.
They will know your Country's modem code, which may be essential for
dialup service.
Responses from Discuss@xxxxxxxxxxxxx are sometimes blocked by an
Internet Provider mail filters.
So in a day, also check the Archived responses at http://www.linmodems.org
-------------------------- System information ----------------------------
CPU=i686,
Welcome , ALSA_version=1.0.21
Linux version 2.6.33-smp (root@midas) (gcc version 4.4.3 (GCC) ) #2
SMP Sat Feb 27 20:12:16 CST 2010
scanModem update of: 2010_02_25
The modem symbolic link is /dev/modem -> /dev/ttyAGS3
/etc/lsb-release not found
Presently install your Linux Distributions dkms package. It provides
for automated driver updates,
following upgrade of your kernel. For details see
http://linux.dell.com/projects.shtml#dkms
Modem drivers blocked from loading during bootup are listed in
/etc/modprobe* file lines:
/etc/modprobe.d/blacklist.conf:blacklist snd-atiixp-modem
/etc/modprobe.d/blacklist.conf:blacklist snd-via82xx-modem
/etc/modprobe.d/blacklist.conf:blacklist snd-intel8x0m
Potentially useful modem drivers now loaded are:
snd_hda_intel agrmodem agrserial
Attached USB devices are:
ID 0bda:0158 Realtek Semiconductor Corp. USB 2.0 multicard reader
ID 15d9:0a41 Unknown
If a cellphone is not detected, see
http://ubuntuforums.org/archive/index.php/t-878554.html
A sample report is:
http://linmodems.technion.ac.il/bigarch/archive-nineth/msg00578.html
If a USB modem or cellphone is attached and was not detected, please
provide available information in your request to discuss@xxxxxxxxxxxxx
Candidate PCI devices with modem chips are:
03:00.0 Communication controller: Agere Systems Device 0630 (rev 01)
00:05.0 Audio device: nVidia Corporation MCP61 High Definition Audio (rev a2)
High Definition Audio cards can host modem chips.
For candidate card in slot 03:00.0, firmware information and bootup
diagnostics are:
PCI slot PCI ID SubsystemID Name
---------- --------- --------- --------------
03:00.0 11c1:0630 11c1:0630 Communication
controller: Agere Systems Device 0630
Modem interrupt assignment and sharing:
16: 15457 IO-APIC-fasteoi LSI Mdm
--- Bootup diagnostics for card in PCI slot 03:00.0 ----
pci 0000:03:00.0: reg 10: [mem 0xfdcff000-0xfdcfffff 64bit]
pci 0000:03:00.0: PME# supported from D3hot D3cold
pci 0000:03:00.0: PME# disabled
pci 0000:03:00.0: PCI INT A -> Link[APC6] -> GSI 16 (level, low) -> IRQ 16
The PCI slot 03:00.0 of the modem card may be disabled early in
a bootup process, but then enabled later. If modem drivers load
but the modem is not responsive, read DOCs/Bootup.txt about possible fixes.
Send dmesg.txt along with ModemData.txt to discuss@xxxxxxxxxxxxx
if help is needed.
For candidate card in slot 00:05.0, firmware information and bootup
diagnostics are:
PCI slot PCI ID SubsystemID Name
---------- --------- --------- --------------
00:05.0 10de:03f0 1025:0153 Audio device: nVidia
Corporation MCP61 High Definition Audio
Modem interrupt assignment and sharing:
27: 1067 PCI-MSI-edge hda_intel
--- Bootup diagnostics for card in PCI slot 00:05.0 ----
pci 0000:00:05.0: reg 10: [mem 0xfe024000-0xfe027fff]
pci 0000:00:05.0: PME# supported from D3hot D3cold
pci 0000:00:05.0: PME# disabled
HDA Intel 0000:00:05.0: PCI INT B -> Link[AAZA] -> GSI 22 (level, low) -> IRQ 22
HDA Intel 0000:00:05.0: irq 27 for MSI/MSI-X
HDA Intel 0000:00:05.0: setting latency timer to 64
The PCI slot 00:05.0 of the modem card may be disabled early in
a bootup process, but then enabled later. If modem drivers load
but the modem is not responsive, read DOCs/Bootup.txt about possible fixes.
Send dmesg.txt along with ModemData.txt to discuss@xxxxxxxxxxxxx
if help is needed.
=== Finished firmware and bootup diagnostics, next deducing cogent software. ===
Predictive diagnostics for card in bus 03:00.0:
Modem chipset detected on
NAME="Communication controller: Agere Systems Device 0630 "
CLASS=0780
PCIDEV=11c1:0630
SUBSYS=11c1:0630
IRQ=16
HDA2=00:05.0
IDENT=agrsm
For candidate modem in: 03:00.0
0780 Communication controller: Agere Systems Device 0630
Primary device ID: 11c1:0630
Support type needed or chipset: agrsm
The AgereSystems/LSI agrsm code supports compiling of a agrmodem +
agrserial driver pair.
There are a few different chipsets which use this driver pair, but
they use different code resources:
Chipsets KV* PackageNames (most current as
of November 2009)
----------------------------------------------------------------------------------------------
11c1:048c and 11c1:048f 2.6.29
agrsm048pci-2.1.60_20100108_i386.deb or
agrsm048pci-2.1.60_20100108.tar.gz
11c1:0620 2.6.31
agrsm06pci-2.1.80_20100106_i386.deb or
agrsm06pci-2.1.80~20100106.tar.gz !!
11c11040 (on HDA audio cards) 2.6.31
agrsm-11c11040_20091225_i386.deb or
agrsm-11c11040-2.1.80~20091225.tar.bz2 !!
All available at:
http://linmodems.technion.ac.il/packages/ltmodem/11c11040/
Additionally there are;
automation & testing agrsm-tools_0.0.1_all.deb or
agrsm-tools-0.0.1-2.noarch.rpm
General background agrsm_howto.txt
------------------------------------------------------------------------------------------------
* KV == latest kernel release with a reported success
!! Latest update with major credit to Nikolay Zhuravlev
But see conflict issue:
http://linmodems.technion.ac.il/bigarch/archive-nineth/msg02753.html
Report from Bjorn Wielens:
Please note- trying to load the modules on a OpenSuSE 11.2 system gives
an error about the module_version symbol. Using:
# modprobe --force agrmodem
# modprobe --force agrserial
is necessary to load the drivers, and does not appear to cause ill effects.
All of the above packages are dkms competent. This means that if your
Linux distros dkms package
is previously installed, if provides for future updates matching
forthcoming kernels.
-------------- end Agere Systems section -------------------
Predictive diagnostics for card in bus 00:05.0:
Modem chipset not detected on
NAME="Audio device: nVidia Corporation MCP61 High Definition Audio "
CLASS=0403
PCIDEV=10de:03f0
SUBSYS=1025:0153
IRQ=27
For candidate modem in: 00:05.0
0403 Audio device: nVidia Corporation MCP61 High Definition Audio
Primary device ID: 10de:03f0
Support type needed or chipset:
Completed candidate modem analyses.
The base of the UDEV device file system is: /dev/.udev
Versions adequately match for the compiler installed: 4.4.3
and the compiler used in kernel assembly: 4.4.3
linux-headers-2.6.33-smp resources needed for compiling are not
manifestly ready!
If compiling is necessary packages must be installed, providing:
kernel-source-2.6.33-smp
If a driver compilation fails, with message including some lack of
some FileName.h (stdio.h for example), then
Some additional kernel-header files need installation to /usr/include.
The minimal additional packages are libc6-dev
and any of its dependents, under Ubuntu linux-libc-dev
If an alternate ethernet connection is available,
$ apt-get update
$ apt-get -s install linux-kernel-devel
will install needed packages.
For Debian/Ubuntu related distributions, run the following command to
display the needed package list:
Otherwise packages have to be found through http://packages.ubuntu.com
Once downloaded and transferred into a Linux partition,
they can be installed alltogether with:
$ sudo dpkg -i *.deb
Checking pppd properties:
-rwxr-xr-x 1 root root 266728 2010-02-12 19:51 /usr/sbin/pppd
In case of an "error 17" "serial loopback" problem, see:
http://linmodems.technion.ac.il/linmodems/archive-sixth/msg02637.html
To enable dialout without Root permission do:
$ su - root (not for Ubuntu)
chmod a+x /usr/sbin/pppd
or under Ubuntu related Linuxes
chmod a+x /usr/sbin/pppd
Checking settings of: /etc/ppp/options
asyncmap 0
crtscts
lock
modem
proxyarp
lcp-echo-interval 30
lcp-echo-failure 4
In case of a message like:
Warning: Could not modify /etc/ppp/pap-secrets: Permission denied
see http://linmodems.technion.ac.il/bigarch/archive-sixth/msg04656.html
For guidance on FAX usage, get from
http://linmodems.technion.ac.il/packages/ get faxing.tar.gz
It has samples for a modem using port /dev/ttySL0, which must be
changed to match your modem's port.
Read Modem/DOCs/YourSystem.txt concerning other COMM channels: ppp0
Which can interfere with Browser naviagation.
Don't worry about the following, it is for experts should trouble
shooting be necessary.
==========================================================
Checking for modem support lines:
--------------------------------------
/device/modem symbolic link: lrwxrwxrwx 1 root root 12
2010-03-03 20:02 /dev/modem -> /dev/ttyAGS3
slmodemd created symbolic link /dev/ttySL0:
Within /etc/udev/ files:
Within /etc/modprobe.conf files:
/etc/modprobe.d/blacklist.conf:# ALSA modules to support sound modems.
These should be loaded manually
/etc/modprobe.d/blacklist.conf:blacklist snd-atiixp-modem
/etc/modprobe.d/blacklist.conf:blacklist snd-via82xx-modem
Within any ancient /etc/devfs files:
Within ancient kernel 2.4.n /etc/module.conf files:
--------- end modem support lines --------
