Re: Humble request for an updated slamr driver for Ubuntu 9.04 ( 2.6.28-11-generic )

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Thanks all!

I was able to get the packages installed, but I'm not able to get the
modem to show up at /dev/slamr or /dev/ttySL0

The modrobe command shows the slamr drive installed but I'm not seeing
the /dev entry for the modem.

I've attached a file(things_tried.txt) with some things I've tried,
please have a look.

Any suggestions would be much appreciated!

Thanks very much!

Shannon VanWagner
http://humans-enabled.com


On Fri, Apr 10, 2009 at 5:52 PM, Marvin Stodolsky
<marvin.stodolsky@xxxxxxxxx> wrote:
> Shannon,
>
> Ahmed's instructions are correct, if you are alternately online by
> ethernet/wireless.
>
> However if not already online, if will be easiest to first get from
> http://linmodems.technion.ac.il/packages/smartlink/Ubuntu/  the
>  slamr-2.6.27-??-generic.tar.gz  that matches the
> kernel 2.6.27-??-generic already installed on your System,
>
> That will enable you to get on line under the 2.6.27-??-generic kernel and run:
> $ sudo apt-get update
> $ sudo apt-get install dkms sl-modem-source
> per Ahmed's instructions.
>
> For service under the 2.6.28-11-generic kernel, you will additionally
> have to install packages from
> http://packages.ubuntu.com/jaunty/linux-headers-2.6.28-11-generic/
> (unless they are already on your system) to enable compiling under
> 2.6.28-11-generic.
>
> That done, when you reboot into 2.6.28-11-generic, the dkms system
> will compile and install the slamr driver.
>
> MarvS
> scanModem maintainer
>
>
> On Fri, Apr 10, 2009 at 11:50 AM, أحمد المحمودي
> <aelmahmoudy@xxxxxxxxxxxxxxxxxxxxx> wrote:
>> On Fri, Apr 10, 2009 at 05:54:41AM -0700, Shannon VanWagner wrote:
>>> I was looking here(and not seeing it):
>>> http://linmodems.technion.ac.il/packages/smartlink/Ubuntu/
>>>
>>> Can you point me to where to download it?
>> ---end quoted text---
>>
>> From Ubuntu repository:
>> http://packages.ubuntu.com/jaunty/sl-modem-source
>>
>> simply run: sudo apt-get install sl-modem-source
>>
>> --
>>  ‎أحمد المحمودي (Ahmed El-Mahmoudy)
>>  Digital design engineer
>>  GPG KeyID: 0x9DCA0B27 (@ subkeys.pgp.net)
>>  GPG Fingerprint: 087D 3767 8CAC 65B1 8F6C  156E D325 C3C8 9DCA 0B27
>>
>
me@mach:~$ sudo apt-get install dkms sl-modem-source 
Reading package lists... Done
Building dependency tree       
Reading state information... Done
The following NEW packages will be installed:
  dkms sl-modem-source
0 upgraded, 2 newly installed, 0 to remove and 15 not upgraded.
Need to get 0B/556kB of archives.
After this operation, 1552kB of additional disk space will be used.
debconf: unable to initialize frontend: Dialog
debconf: (Dialog frontend requires a screen at least 13 lines tall and 31 columns wide.)
debconf: falling back to frontend: Readline
Selecting previously deselected package dkms.
(Reading database ... 105038 files and directories currently installed.)
Unpacking dkms (from .../dkms_2.0.21.1-0ubuntu3_all.deb) ...
Selecting previously deselected package sl-modem-source.
Unpacking sl-modem-source (from .../sl-modem-source_2.9.11~20080817-3ubuntu2_i386.deb) ...
Processing triggers for man-db ...
Setting up dkms (2.0.21.1-0ubuntu3) ...
 * Running DKMS auto installation service for kernel 2.6.28-11-generic   [ OK ] 

Setting up sl-modem-source (2.9.11~20080817-3ubuntu2) ...
Adding Module to DKMS build system
Doing initial module build
Installing initial module
Done.

me@mach:~$     sudo modprobe ungrab-winmodem
me@mach:~$     sudo modprobe slamr
me@mach:~$     sudo  slmodemd -c USA  /dev/slamr0
error: mdm setup: cannot stat `/dev/slamr0': No such file or directory
error: cannot setup device `/dev/slamr0'


me@mach:~$ sudo /etc/init.d/sl-modem-daemon restart
Shutting down SmartLink Modem driver normally ... no slmodemd daemon running.
Unloading modem driver from kernel ... slamr.
Starting SmartLink Modem driver for: slamr0.
Creating /dev/modem symlink, pointing to: /dev/ttySL0.

me@mach:~$ sudo modprobe -r slamr
me@mach:~$ sudo modprobe slamr
me@mach:~$ sudo slmodemd /dev/slamr0
error: mdm setup: cannot stat `/dev/slamr0': No such file or directory
error: cannot setup device `/dev/slamr0'


me@mach:~$ sudo /etc/init.d/sl-modem-daemon restart
Shutting down SmartLink Modem driver normally ... no slmodemd daemon running.
Unloading modem driver from kernel ... slamr.
Starting SmartLink Modem driver for: slamr0.
Creating /dev/modem symlink, pointing to: /dev/ttySL0.
me@mach:~$             modprobe -r slamr
FATAL: Error removing slamr (/lib/modules/2.6.28-11-generic/updates/dkms/slamr.ko): Operation not permitted
me@mach:~$             modprobe  slamr
me@mach:~$ sudo modprobe -r slamr
me@mach:~$ modprobe slamr
FATAL: Error inserting slamr (/lib/modules/2.6.28-11-generic/updates/dkms/slamr.ko): Operation not permitted
me@mach:~$ sudo modprobe slamr
me@mach:~$ sudo slmodemd /dev/slamr0
error: mdm setup: cannot stat `/dev/slamr0': No such file or directory
error: cannot setup device `/dev/slamr0'
me@mach:~$ sudo dmesg |tail
[    6.022249] eth0: RealTek RTL8139 at 0xa800, 00:e0:7d:d1:b5:6f, IRQ 11
[    6.022260] eth0:  Identified 8139 chip type 'RTL-8100B/8139D'
[    7.005957] Marking TSC unstable due to TSC halts in idle
[    7.115523] PM: Starting manual resume from disk
[    7.115539] PM: Resume from partition 8:17
[    7.115546] PM: Checking hibernation image.
[    7.115944] PM: Resume from disk failed.
[    7.124330] EXT3-fs: INFO: recovery required on readonly filesystem.
[    7.124345] EXT3-fs: write access will be enabled during recovery.
[    7.477117] kjournald starting.  Commit interval 5 seconds
[    7.477175] EXT3-fs: recovery complete.
[    7.477876] EXT3-fs: mounted filesystem with ordered data mode.
[   14.248458] udev: starting version 141
[   14.529460] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   14.633094] Linux agpgart interface v0.103
[   14.654846] agpgart: Detected VIA Apollo Pro 133 chipset
[   14.657735] agpgart-via 0000:00:00.0: AGP aperture is 32M @ 0xe6000000
[   14.978294] prism2_usb: module is from the staging directory, the quality is unknown, you have been warned.
[   15.603321] input: PC Speaker as /devices/platform/pcspkr/input/input5
[   16.454803] ident: nic h/w: id=0x8026 1.0.0
[   16.455714] ident: pri f/w: id=0x15 1.1.2
[   16.457233] ident: sta f/w: id=0x1f 1.5.6
[   16.457722] MFI:SUP:role=0x00:id=0x01:var=0x01:b/t=1/1
[   16.458756] CFI:SUP:role=0x00:id=0x02:var=0x02:b/t=1/1
[   16.459777] PRI:SUP:role=0x00:id=0x03:var=0x01:b/t=1/4
[   16.460729] STA:SUP:role=0x00:id=0x04:var=0x01:b/t=1/10
[   16.461865] PRI-CFI:ACT:role=0x01:id=0x02:var=0x02:b/t=1/1
[   16.462856] STA-CFI:ACT:role=0x01:id=0x02:var=0x02:b/t=1/1
[   16.463730] STA-MFI:ACT:role=0x01:id=0x01:var=0x01:b/t=1/1
[   16.464774] Prism2 card SN: 1\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00
[   16.468864] usbcore: registered new interface driver prism2_usb
[   16.604779] ENS1371 0000:00:0a.0: PCI INT A -> Link[LNKC] -> GSI 10 (level, low) -> IRQ 10
[   18.005780] lp: driver loaded but no devices found
[   18.382292] Adding 1277128k swap on /dev/sda5.  Priority:-1 extents:1 across:1277128k
[   19.042002] EXT3 FS on sda1, internal journal
[   20.847020] type=1505 audit(1239478098.742:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=1798
[   21.070514] type=1505 audit(1239478098.966:3): operation="profile_load" name="/sbin/dhclient-script" name2="default" pid=1802
[   21.071265] type=1505 audit(1239478098.966:4): operation="profile_load" name="/sbin/dhclient3" name2="default" pid=1802
[   21.071614] type=1505 audit(1239478098.966:5): operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" name2="default" pid=1802
[   21.071875] type=1505 audit(1239478098.966:6): operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" name2="default" pid=1802
[   21.708395] type=1505 audit(1239478099.606:7): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=1807
[   21.709448] type=1505 audit(1239478099.606:8): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=1807
[   21.844836] type=1505 audit(1239478099.742:9): operation="profile_load" name="/usr/sbin/tcpdump" name2="default" pid=1811
[   24.859343] slamr: module license 'Smart Link Ltd.' taints kernel.
[   24.886691] slamr: SmartLink AMRMO modem.
[   24.886734] slamr: device 10b9:545a is grabbed by another driver
[   28.434598] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   28.434610] Bluetooth: BNEP filters: protocol multicast
[   28.541108] Bridge firewalling registered
[   31.338194] linkstatus=DISCONNECTED (unhandled)
[   31.908115] ppdev: user-space parallel port driver
[   35.104377] eth0: link down
[   35.105461] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   35.112388] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   35.989454] linkstatus=CONNECTED
[   36.813904] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   47.336046] wlan0: no IPv6 routers present
[   92.099097] linkstatus=DISCONNECTED (unhandled)
[   92.562764] linkstatus=CONNECTED
[  659.858088] linkstatus=AP_OUTOFRANGE (unhandled)
[  660.333814] linkstatus=AP_INRANGE
[  662.744206] linkstatus=AP_OUTOFRANGE (unhandled)
[  665.537358] linkstatus=AP_INRANGE
[  668.249481] linkstatus=AP_OUTOFRANGE (unhandled)
[  668.676254] linkstatus=AP_INRANGE
[  678.689605] linkstatus=AP_OUTOFRANGE (unhandled)
[  679.395041] linkstatus=AP_INRANGE
[  681.935366] linkstatus=AP_OUTOFRANGE (unhandled)
[  682.733809] linkstatus=AP_INRANGE
[  685.276131] linkstatus=AP_OUTOFRANGE (unhandled)
[  685.987706] linkstatus=AP_INRANGE
[  696.293849] linkstatus=AP_OUTOFRANGE (unhandled)
[  696.812428] linkstatus=AP_INRANGE
[  699.364739] linkstatus=AP_OUTOFRANGE (unhandled)
[  699.882369] linkstatus=AP_INRANGE
[  702.293834] linkstatus=AP_OUTOFRANGE (unhandled)
[  702.952328] linkstatus=AP_INRANGE
[  714.512682] linkstatus=AP_OUTOFRANGE (unhandled)
[  714.894414] linkstatus=AP_INRANGE
[  726.805683] linkstatus=AP_OUTOFRANGE (unhandled)
[  727.166232] linkstatus=AP_INRANGE
[  729.705507] linkstatus=AP_OUTOFRANGE (unhandled)
[  731.862353] linkstatus=AP_INRANGE
[  735.185823] linkstatus=AP_OUTOFRANGE (unhandled)
[  735.705520] linkstatus=AP_INRANGE
[  738.092210] device 10b9:545a is grabbed by driver serial: try to release
[  738.094520] serial 0000:00:0e.0: PCI INT A disabled
[  739.689835] linkstatus=AP_OUTOFRANGE (unhandled)
[  740.210522] linkstatus=AP_INRANGE
[  743.170502] linkstatus=AP_OUTOFRANGE (unhandled)
[  743.643257] linkstatus=AP_INRANGE
[  834.697263] slamr: SmartLink AMRMO modem.
[  834.697397] slamr: probe 10b9:545a ALI545A card...
[  834.697442] slamr 0000:00:0e.0: PCI INT A -> Link[LNKC] -> GSI 10 (level, low) -> IRQ 10
[  834.697879] slamr: slamr0 is ALI545A card.
[  860.823342] slamr 0000:00:0e.0: PCI INT A disabled
[  871.053729] slamr: SmartLink AMRMO modem.
[  871.053872] slamr: probe 10b9:545a ALI545A card...
[  871.053919] slamr 0000:00:0e.0: PCI INT A -> Link[LNKC] -> GSI 10 (level, low) -> IRQ 10
[  871.054363] slamr: slamr0 is ALI545A card.


 





barbara@ubuntu-barb:~$ sudo cat /var/log/messages |tail -100
Apr 11 12:28:22 ubuntu-barb kernel: [    5.996855] 8139cp 0000:00:0c.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip, use 8139too
Apr 11 12:28:22 ubuntu-barb kernel: [    6.018216] 8139too Fast Ethernet driver 0.9.28
Apr 11 12:28:22 ubuntu-barb kernel: [    6.019465] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
Apr 11 12:28:22 ubuntu-barb kernel: [    6.019492] 8139too 0000:00:0c.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
Apr 11 12:28:22 ubuntu-barb kernel: [    6.022249] eth0: RealTek RTL8139 at 0xa800, 00:e0:7d:d1:b5:6f, IRQ 11
Apr 11 12:28:22 ubuntu-barb kernel: [    7.005957] Marking TSC unstable due to TSC halts in idle
Apr 11 12:28:22 ubuntu-barb kernel: [    7.115523] PM: Starting manual resume from disk
Apr 11 12:28:22 ubuntu-barb kernel: [    7.124330] EXT3-fs: INFO: recovery required on readonly filesystem.
Apr 11 12:28:22 ubuntu-barb kernel: [    7.124345] EXT3-fs: write access will be enabled during recovery.
Apr 11 12:28:22 ubuntu-barb kernel: [    7.477117] kjournald starting.  Commit interval 5 seconds
Apr 11 12:28:22 ubuntu-barb kernel: [    7.477175] EXT3-fs: recovery complete.
Apr 11 12:28:22 ubuntu-barb kernel: [    7.477876] EXT3-fs: mounted filesystem with ordered data mode.
Apr 11 12:28:22 ubuntu-barb kernel: [   14.248458] udev: starting version 141
Apr 11 12:28:22 ubuntu-barb kernel: [   14.529460] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Apr 11 12:28:22 ubuntu-barb kernel: [   14.633094] Linux agpgart interface v0.103
Apr 11 12:28:22 ubuntu-barb kernel: [   14.654846] agpgart: Detected VIA Apollo Pro 133 chipset
Apr 11 12:28:22 ubuntu-barb kernel: [   14.657735] agpgart-via 0000:00:00.0: AGP aperture is 32M @ 0xe6000000
Apr 11 12:28:22 ubuntu-barb kernel: [   14.978294] prism2_usb: module is from the staging directory, the quality is unknown, you have been warned.
Apr 11 12:28:22 ubuntu-barb kernel: [   15.603321] input: PC Speaker as /devices/platform/pcspkr/input/input5
Apr 11 12:28:22 ubuntu-barb kernel: [   16.454803] ident: nic h/w: id=0x8026 1.0.0
Apr 11 12:28:22 ubuntu-barb kernel: [   16.455714] ident: pri f/w: id=0x15 1.1.2
Apr 11 12:28:22 ubuntu-barb kernel: [   16.457233] ident: sta f/w: id=0x1f 1.5.6
Apr 11 12:28:22 ubuntu-barb kernel: [   16.457722] MFI:SUP:role=0x00:id=0x01:var=0x01:b/t=1/1
Apr 11 12:28:22 ubuntu-barb kernel: [   16.458756] CFI:SUP:role=0x00:id=0x02:var=0x02:b/t=1/1
Apr 11 12:28:22 ubuntu-barb kernel: [   16.459777] PRI:SUP:role=0x00:id=0x03:var=0x01:b/t=1/4
Apr 11 12:28:22 ubuntu-barb kernel: [   16.460729] STA:SUP:role=0x00:id=0x04:var=0x01:b/t=1/10
Apr 11 12:28:22 ubuntu-barb kernel: [   16.461865] PRI-CFI:ACT:role=0x01:id=0x02:var=0x02:b/t=1/1
Apr 11 12:28:22 ubuntu-barb kernel: [   16.462856] STA-CFI:ACT:role=0x01:id=0x02:var=0x02:b/t=1/1
Apr 11 12:28:22 ubuntu-barb kernel: [   16.463730] STA-MFI:ACT:role=0x01:id=0x01:var=0x01:b/t=1/1
Apr 11 12:28:22 ubuntu-barb kernel: [   16.464774] Prism2 card SN: 1\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00
Apr 11 12:28:22 ubuntu-barb kernel: [   16.468864] usbcore: registered new interface driver prism2_usb
Apr 11 12:28:22 ubuntu-barb kernel: [   16.604779] ENS1371 0000:00:0a.0: PCI INT A -> Link[LNKC] -> GSI 10 (level, low) -> IRQ 10
Apr 11 12:28:22 ubuntu-barb kernel: [   18.005780] lp: driver loaded but no devices found
Apr 11 12:28:22 ubuntu-barb kernel: [   18.382292] Adding 1277128k swap on /dev/sda5.  Priority:-1 extents:1 across:1277128k
Apr 11 12:28:22 ubuntu-barb kernel: [   19.042002] EXT3 FS on sda1, internal journal
Apr 11 12:28:22 ubuntu-barb kernel: [   20.847020] type=1505 audit(1239478098.742:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=1798
Apr 11 12:28:22 ubuntu-barb kernel: [   21.070514] type=1505 audit(1239478098.966:3): operation="profile_load" name="/sbin/dhclient-script" name2="default" pid=1802
Apr 11 12:28:22 ubuntu-barb kernel: [   21.071265] type=1505 audit(1239478098.966:4): operation="profile_load" name="/sbin/dhclient3" name2="default" pid=1802
Apr 11 12:28:22 ubuntu-barb kernel: [   21.071614] type=1505 audit(1239478098.966:5): operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" name2="default" pid=1802
Apr 11 12:28:22 ubuntu-barb kernel: [   21.071875] type=1505 audit(1239478098.966:6): operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" name2="default" pid=1802
Apr 11 12:28:22 ubuntu-barb kernel: [   21.708395] type=1505 audit(1239478099.606:7): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=1807
Apr 11 12:28:22 ubuntu-barb kernel: [   21.709448] type=1505 audit(1239478099.606:8): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=1807
Apr 11 12:28:22 ubuntu-barb kernel: [   21.844836] type=1505 audit(1239478099.742:9): operation="profile_load" name="/usr/sbin/tcpdump" name2="default" pid=1811
Apr 11 12:28:22 ubuntu-barb kernel: [   24.859343] slamr: module license 'Smart Link Ltd.' taints kernel.
Apr 11 12:28:22 ubuntu-barb kernel: [   24.886691] slamr: SmartLink AMRMO modem.
Apr 11 12:28:22 ubuntu-barb kernel: [   24.886734] slamr: device 10b9:545a is grabbed by another driver
Apr 11 12:28:26 ubuntu-barb kernel: [   28.434598] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Apr 11 12:28:26 ubuntu-barb kernel: [   28.434610] Bluetooth: BNEP filters: protocol multicast
Apr 11 12:28:26 ubuntu-barb kernel: [   28.541108] Bridge firewalling registered
Apr 11 12:28:29 ubuntu-barb kernel: [   31.338194] linkstatus=DISCONNECTED (unhandled)
Apr 11 12:28:29 ubuntu-barb kernel: [   31.908115] ppdev: user-space parallel port driver
Apr 11 12:28:33 ubuntu-barb kernel: [   35.104377] eth0: link down
Apr 11 12:28:33 ubuntu-barb kernel: [   35.105461] ADDRCONF(NETDEV_UP): eth0: link is not ready
Apr 11 12:28:33 ubuntu-barb kernel: [   35.112388] ADDRCONF(NETDEV_UP): wlan0: link is not ready
Apr 11 12:28:33 ubuntu-barb kernel: [   35.989454] linkstatus=CONNECTED
Apr 11 12:28:34 ubuntu-barb kernel: [   36.813904] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Apr 11 12:29:13 ubuntu-barb pulseaudio[2982]: alsa-util.c: Device front:0 doesn't support 44100 Hz, changed to 44099 Hz.
Apr 11 12:29:29 ubuntu-barb kernel: [   92.099097] linkstatus=DISCONNECTED (unhandled)
Apr 11 12:29:30 ubuntu-barb kernel: [   92.562764] linkstatus=CONNECTED
Apr 11 12:38:57 ubuntu-barb kernel: [  659.858088] linkstatus=AP_OUTOFRANGE (unhandled)
Apr 11 12:38:58 ubuntu-barb kernel: [  660.333814] linkstatus=AP_INRANGE
Apr 11 12:39:00 ubuntu-barb kernel: [  662.744206] linkstatus=AP_OUTOFRANGE (unhandled)
Apr 11 12:39:03 ubuntu-barb kernel: [  665.537358] linkstatus=AP_INRANGE
Apr 11 12:39:06 ubuntu-barb kernel: [  668.249481] linkstatus=AP_OUTOFRANGE (unhandled)
Apr 11 12:39:06 ubuntu-barb kernel: [  668.676254] linkstatus=AP_INRANGE
Apr 11 12:39:16 ubuntu-barb kernel: [  678.689605] linkstatus=AP_OUTOFRANGE (unhandled)
Apr 11 12:39:17 ubuntu-barb kernel: [  679.395041] linkstatus=AP_INRANGE
Apr 11 12:39:19 ubuntu-barb kernel: [  681.935366] linkstatus=AP_OUTOFRANGE (unhandled)
Apr 11 12:39:20 ubuntu-barb kernel: [  682.733809] linkstatus=AP_INRANGE
Apr 11 12:39:23 ubuntu-barb kernel: [  685.276131] linkstatus=AP_OUTOFRANGE (unhandled)
Apr 11 12:39:23 ubuntu-barb kernel: [  685.987706] linkstatus=AP_INRANGE
Apr 11 12:39:34 ubuntu-barb kernel: [  696.293849] linkstatus=AP_OUTOFRANGE (unhandled)
Apr 11 12:39:34 ubuntu-barb kernel: [  696.812428] linkstatus=AP_INRANGE
Apr 11 12:39:37 ubuntu-barb kernel: [  699.364739] linkstatus=AP_OUTOFRANGE (unhandled)
Apr 11 12:39:37 ubuntu-barb kernel: [  699.882369] linkstatus=AP_INRANGE
Apr 11 12:39:40 ubuntu-barb kernel: [  702.293834] linkstatus=AP_OUTOFRANGE (unhandled)
Apr 11 12:39:40 ubuntu-barb kernel: [  702.952328] linkstatus=AP_INRANGE
Apr 11 12:39:52 ubuntu-barb kernel: [  714.512682] linkstatus=AP_OUTOFRANGE (unhandled)
Apr 11 12:39:52 ubuntu-barb kernel: [  714.894414] linkstatus=AP_INRANGE
Apr 11 12:40:04 ubuntu-barb kernel: [  726.805683] linkstatus=AP_OUTOFRANGE (unhandled)
Apr 11 12:40:05 ubuntu-barb kernel: [  727.166232] linkstatus=AP_INRANGE
Apr 11 12:40:07 ubuntu-barb kernel: [  729.705507] linkstatus=AP_OUTOFRANGE (unhandled)
Apr 11 12:40:09 ubuntu-barb kernel: [  731.862353] linkstatus=AP_INRANGE
Apr 11 12:40:13 ubuntu-barb kernel: [  735.185823] linkstatus=AP_OUTOFRANGE (unhandled)
Apr 11 12:40:13 ubuntu-barb kernel: [  735.705520] linkstatus=AP_INRANGE
Apr 11 12:40:15 ubuntu-barb kernel: [  738.092210] device 10b9:545a is grabbed by driver serial: try to release
Apr 11 12:40:15 ubuntu-barb kernel: [  738.094520] serial 0000:00:0e.0: PCI INT A disabled
Apr 11 12:40:17 ubuntu-barb kernel: [  739.689835] linkstatus=AP_OUTOFRANGE (unhandled)
Apr 11 12:40:18 ubuntu-barb kernel: [  740.210522] linkstatus=AP_INRANGE
Apr 11 12:40:21 ubuntu-barb kernel: [  743.170502] linkstatus=AP_OUTOFRANGE (unhandled)
Apr 11 12:40:21 ubuntu-barb kernel: [  743.643257] linkstatus=AP_INRANGE
Apr 11 12:41:52 ubuntu-barb kernel: [  834.697263] slamr: SmartLink AMRMO modem.
Apr 11 12:41:52 ubuntu-barb kernel: [  834.697397] slamr: probe 10b9:545a ALI545A card...
Apr 11 12:41:52 ubuntu-barb kernel: [  834.697442] slamr 0000:00:0e.0: PCI INT A -> Link[LNKC] -> GSI 10 (level, low) -> IRQ 10
Apr 11 12:41:52 ubuntu-barb kernel: [  834.697879] slamr: slamr0 is ALI545A card.
Apr 11 12:42:18 ubuntu-barb kernel: [  860.823342] slamr 0000:00:0e.0: PCI INT A disabled
Apr 11 12:42:28 ubuntu-barb kernel: [  871.053729] slamr: SmartLink AMRMO modem.
Apr 11 12:42:28 ubuntu-barb kernel: [  871.053872] slamr: probe 10b9:545a ALI545A card...
Apr 11 12:42:28 ubuntu-barb kernel: [  871.053919] slamr 0000:00:0e.0: PCI INT A -> Link[LNKC] -> GSI 10 (level, low) -> IRQ 10
Apr 11 12:42:28 ubuntu-barb kernel: [  871.054363] slamr: slamr0 is ALI545A card.













[Index of Archives]     [Linux Media Development]     [Asterisk]     [DCCP]     [Netdev]     [X.org]     [Xfree86]     [Fedora Women]     [Linux USB]

  Powered by Linux