I am a bit confused on how the QSPI image is built.
>From images/Makefile.layerscape
$(obj)/barebox-ls1046ardb-qspi.image: $(obj)/start_ls1046ardb.pblb \
$(board)/ls1046ardb/ls1046ardb_rcw_qspi.cfg \
$(board)/ls1046ardb/ls1046ardb_pbi.cfg
It makes use of the file ls1046ardb/ls1046ardb_pbi.cfg not ls1046ardb/ls1046ardb_qspi_pbi.cfg.
ls1046a_qspi_pbi.cfg contains an endian swap that I can see in the U-boot rcw+pbi data.
When I take an hex dump of the barebox-ls1046ardb-qspi.image, I see that the scratchpad register 2 (BOOTLOCPTR) in the PBI section points to 0x10000000 (as in the PBI file), not the PBL address start address.
How can this work?
Renaud
-----Original Message-----
From: Ahmad Fatoum <a.fatoum@xxxxxxxxxxxxxx>
Sent: 10 June 2021 15:09
To: Barbier, Renaud <renaud.barbier@xxxxxxxxx>; Barebox List <barebox@xxxxxxxxxxxxxxxxxxx>
Subject: Re: NXP Layerscape
[**EXTERNAL SOURCE**]:Please verify the source before clicking link or opening attachment.
Hello Barbier,
On 10.06.21 15:49, Barbier, Renaud wrote:
> I received a NXP LS1046A-RDB
It doesn't reboot cleanly with a USB serial adapter attached!
Jfyi, gave me a scare first time, when I thought I broke something ^^.
>
> I built barebox for the LS1046A and got the image barebox-ls1046ardb-qspi.image.
> I programmed the image in the alternative SPI bank as per NXP instructions:
> => tftp $load_addr
> => sf erase 0 +$filesize && sf write $load_addr 0 $filesize
>
> Barebox does not boot.
>
> I did notice that u-boot is at address 0x40100000 while the RCW is at 0x40000000.
> My understanding is that barebox is one image and shall be programmed
> at offset 0 of the SPI (0x40000000)
Can't comment on that. Sascha did the integration.
> At present I cannot connect my I.C.E. due a pin stuck in my MIPI connector.
>
> Any return on experience is welcome.
Can comment on that: Last time I did this, I wrote some documentation:
https://nam11.safelinks.protection.outlook.com/?url=https%3A%2F%2Fwww.barebox.org%2Fdoc%2Flatest%2Fboards%2Flayerscape.html&data=04%7C01%7Crenaud.barbier%40abaco.com%7Cdf668f5e5f2d497d54cb08d92c194c3e%7Ce6f27451899d4d0db8fa88baafa551a7%7C0%7C0%7C637589309423979193%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C1000&sdata=SnXT0WYjQMJL%2FwK1LaOK1h7OMUcLiL37cojY2hzP89s%3D&reserved=0
There I flashed barebox from another barebox booted from SD-Card.
I'd assume that should still work. I can't recall how the CPLD needed to be tickled, but it would be helpful to know whether doing it like described in the documentation doesn't work for you.
Cheers,
Ahmad
>
> Cheers,
> Renaud
>
>
> _______________________________________________
> barebox mailing list
> barebox@xxxxxxxxxxxxxxxxxxx
> https://nam11.safelinks.protection.outlook.com/?url=http%3A%2F%2Flists
> .infradead.org%2Fmailman%2Flistinfo%2Fbarebox&data=04%7C01%7Crenau
> d.barbier%40abaco.com%7Cdf668f5e5f2d497d54cb08d92c194c3e%7Ce6f27451899
> d4d0db8fa88baafa551a7%7C0%7C0%7C637589309423989184%7CUnknown%7CTWFpbGZ
> sb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3
> D%7C1000&sdata=ORpVZlyPk2o7%2FyVYOkJPeAWNnq2%2FkxKauxep7gvDJ%2Bo%3
> D&reserved=0
>
--
Pengutronix e.K. | |
Steuerwalder Str. 21 | https://nam11.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.pengutronix.de%2F&data=04%7C01%7Crenaud.barbier%40abaco.com%7Cdf668f5e5f2d497d54cb08d92c194c3e%7Ce6f27451899d4d0db8fa88baafa551a7%7C0%7C0%7C637589309423989184%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C1000&sdata=hB2sfEPHomEzn0ICOo9o%2BfRwu3kpXuSvyGZ%2FP%2FnRmpc%3D&reserved=0 |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
_______________________________________________
barebox mailing list
barebox@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/barebox
