Yes I think you are right. I need to find the setup disk :) Thanks >> Last time I checked the 3c59X line was a 10 MBPS half duplex >> card. > Sorry but I've to correct you and that one. On my desk: > 3COM Fast Etherlink PCI 10/100 Base-T Ethernet Adapter 3C595-TX. > Maybe the first in the 3C59X series were not capable of 100Mbit, but this > one is for sure. > >> the 3C90X series is the 100 MBPS card. You might >> want to double the card model, but you will never be able >> to make a 3c59x ANYTHING GO FASTER THAN 10 mBPS. > > Do you have the 3COM configuration floppy? Then you can boot from a > DOS/W98 > rescue boot floppy and configure the adapter via this tool on 100Mbit-FD > (if > possible ;-). > > Cheers, > Andre >> > -----Original Message----- >> > From: redhat-list-admin@xxxxxxxxxx >> > [mailto:redhat-list-admin@xxxxxxxxxx]On Behalf Of Thierry >> ITTY >> > Sent: Wednesday, October 29, 2003 8:28 AM >> > To: redhat-list@xxxxxxxxxx >> > Subject: Re: 3c59x won't negotiate 100mb full duplex >> > >> > >> > what if you force it >> > mii-tool -F 100baseTx-FD eth1 >> > >> > hth >> > >> > >> > A 15:03 28/10/2003 -0600, vous avez écrit : >> > >I can't get a 3Com card (eth1) to negotiate 100mb, here >> are >> > the details of >> > >my setup. Any ideas what I can do ? >> > > >> > >modules.conf >> > >alias parport_lowlevel parport_pc >> > >alias scsi_hostadapter aic7xxx >> > >alias eth0 3c59x debug=9 options=4 full_duplex=1 >> > >alias scsi_hostadapter1 ips >> > >alias eth1 3c59x full_duplex=1 >> > >options 3c59x debug=3 options=0x30,0x30 full_duplex=1,1 >> > > >> > >mii-tool >> > >eth0: 100 Mbit, full duplex, link ok >> > >eth1: 10 Mbit, half duplex, no link >> > > >> > >/var/log/messages >> > >Oct 10 16:51:22 kernel: 01:0a.0: 3Com PCI 3c905B Cyclone >> > 100baseTx at >> > >0xe880. Vers LK1.1.18-ac >> > >Oct 10 16:51:22 kernel: 00:50:04:84:e0:4c, IRQ 10 >> > >Oct 10 16:51:22 kernel: product code 544e rev 00.9 >> date 05-13-99 >> > >Oct 10 16:51:22 kernel: Full duplex capable >> > >Oct 10 16:51:22 kernel: 8K byte-wide RAM 5:3 Rx:Tx >> split, >> > 100baseTX >> > >interface. >> > >Oct 10 16:51:22 kernel: Enabling bus-master transmits >> and >> > whole-frame >> > >receives. >> > > >> > >Thanks >> > > >> > >-- >> > > >> > > >> > >-- >> > >redhat-list mailing list >> > >unsubscribe >> mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe >> >https://www.redhat.com/mailman/listinfo/redhat-list >> > >> > >> >> >> -- >> redhat-list mailing list >> unsubscribe >> mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe >> https://www.redhat.com/mailman/listinfo/redhat-list >> >> >> -- >> redhat-list mailing list >> unsubscribe mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe >> https://www.redhat.com/mailman/listinfo/redhat-list >> > > > -- > redhat-list mailing list > unsubscribe mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe > https://www.redhat.com/mailman/listinfo/redhat-list > -- -- redhat-list mailing list unsubscribe mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe https://www.redhat.com/mailman/listinfo/redhat-list
