> -----Original Message----- > From: NeilBrown [mailto:neilb@xxxxxxx] > Sent: Wednesday, January 19, 2011 9:49 PM > To: Kwolek, Adam > Cc: linux-raid@xxxxxxxxxxxxxxx; Williams, Dan J; Ciechanowski, Ed; > Neubauer, Wojciech > Subject: Re: [PATCH 1/2] md/raid5: FIX: manually-added spare is not > used > > On Mon, 17 Jan 2011 14:13:34 +0000 "Kwolek, Adam" > <adam.kwolek@xxxxxxxxx> > wrote: > > > > > > > > -----Original Message----- > > > From: NeilBrown [mailto:neilb@xxxxxxx] > > > Sent: Monday, January 17, 2011 1:45 AM > > > To: Kwolek, Adam > > > Cc: linux-raid@xxxxxxxxxxxxxxx; Williams, Dan J; Ciechanowski, Ed; > > > Neubauer, Wojciech > > > Subject: Re: [PATCH 1/2] md/raid5: FIX: manually-added spare is not > > > used > > > > > > On Mon, 17 Jan 2011 10:28:21 +1100 NeilBrown <neilb@xxxxxxx> wrote: > > > > > > > On Mon, 17 Jan 2011 10:11:28 +1100 NeilBrown <neilb@xxxxxxx> > wrote: > > > > > > > > > On Fri, 14 Jan 2011 14:00:00 +0100 Adam Kwolek > > > <adam.kwolek@xxxxxxxxx> wrote: > > > > > > > > > > > Manually added spares are not used due to fact that they not > > > added to md configuration. > > > > > > Counters are updated only. > > > > > > > > > > > > Signed-off-by: Adam Kwolek <adam.kwolek@xxxxxxxxx> > > > > > > --- > > > > > > > > > > > > drivers/md/raid5.c | 6 ++++-- > > > > > > 1 files changed, 4 insertions(+), 2 deletions(-) > > > > > > > > > > > > diff --git a/drivers/md/raid5.c b/drivers/md/raid5.c > > > > > > index a2087c7..59c4150 100644 > > > > > > --- a/drivers/md/raid5.c > > > > > > +++ b/drivers/md/raid5.c > > > > > > @@ -5592,8 +5592,10 @@ static int raid5_start_reshape(mddev_t > > > *mddev) > > > > > > } else if (rdev->raid_disk >= conf- > > > >previous_raid_disks > > > > > > && !test_bit(Faulty, &rdev->flags)) { > > > > > > /* This is a spare that was manually added */ > > > > > > - set_bit(In_sync, &rdev->flags); > > > > > > - added_devices++; > > > > > > + if (raid5_add_disk(mddev, rdev) == 0) { > > > > > > + set_bit(In_sync, &rdev->flags); > > > > > > + added_devices++; > > > > > > + } > > > > > > } > > > > > > > > > > > > /* When a reshape changes the number of devices, ->degraded > > > > > > > > > > This should not be needed. > > > > > When a device is manually added, the desired slot number is > written > > > to > > > > > ..../md/dev-XXX/slot > > > > > > > > > > This calls slot_store (in md.c) which call mddev->pers- > > > >hot_add_disk which > > > > > for raid5 is raid5_add_disk. > > > > > So you shouldn't need to call raid5_add_disk again. > > > > > > > > > > > > > ahhh... I see. raid5_add_disk doesn't do the right thing in that > > > case. It > > > > actually indexes beyond the end of an array, which is bad. > > > > > > > > We possibly do need the raid5_add_disk where you had put it. > I'll > > > have a > > > > think and see what is best. > > > > > > On third thoughts, I cannot see the problem you are seeing. > > > I even did some simple testing (manually writing to things in > sysfs) > > > and it > > > seems to include the new device properly. > > > > > > There are some issues that I found which are address by the > following > > > patch, > > > but it isn't clear to me that any of them relate to what you are > > > seeing. > > > Maybe if you could be more specific about what you see happening? > > > > > > Thanks, > > > NeilBrown > > > > > > When I'm not using raid5_add_disk() in raid5_start_reshape() added > disk LED light doesn't blinks > > (but it should during reshape ;)), > > md doesn't make any signs that something goes wrong (even size can be > increased). > > > > I've made some debug, and at second (during reshape start) > raid5_add_disk() call rcu_assign_pointer() is called again. > > This means that somehow previous assignment when slot is set was > cleared. > > > > Correct situation (all disks are used during reshape) I can archive > when instead raid5_add_disk() call > > I've add the following code: > > > > struct disk_info *p = conf->disks + rdev->raid_disk; > > rcu_assign_pointer(p->rdev, rdev); > > > > and (conf->disks + rdev->raid_disk)->rdev pointer is present in > configuration. > > I've checked that if I do not do call to rcu_assign_pointer() pointer > (p->rdev) has NULL value. > > In both cases call rcu_assign_pointer() sets p->rdev to the same > value, so rdev doesn't change his location in memory. > > > > > > BR > > Adam > > > > Could you put some debug printks in slot_store (in md.c) and make sure > it is > being called, and that it calls raid5_add_disk, and see what > raid5_add_disk > does in that case? > Thanks, > > NeilBrown I've did it before (and I've double checked now). slot_store() calls raid5_add_disk() and inside it, rcu_assign_pointer() sets correct rdev pointer (I've checked, it is set during slot_store() call). During raid5_start_reshape() this pointer has NULL value. When I set it again, disk is used properly. Second time rdev pointer I'm setting is the same as I've set during slot_store() call. It seems that slot_store() works correctly. I've didn't find why rdev pointer is cleaned meanwhile. I have it in my plans after I've close mdadm OLCE/migration code (main parts at least ;)). BR Adam -- To unsubscribe from this list: send the line "unsubscribe linux-raid" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
