Hi Tobias, On Tue, 20 Jul 2010 23:26:04 +0200, Tobias Preclik wrote: > On Sun, Jul 18, 2010 at 08:02:52AM -0400, Tobias Preclik wrote: > > # sensors > > w83667hg-isa-0a10 > > Adapter: ISA adapter > > in0: +0.98 V (min = +0.00 V, max = +1.74 V) > > in1: +1.11 V (min = +0.10 V, max = +0.20 V) ALARM > > in2: +3.36 V (min = +3.95 V, max = +3.28 V) ALARM > > in3: +3.36 V (min = +1.57 V, max = +2.10 V) ALARM > > in4: +1.10 V (min = +1.74 V, max = +1.87 V) ALARM > > in5: +1.18 V (min = +1.02 V, max = +1.30 V) > > in7: +3.28 V (min = +3.23 V, max = +2.62 V) ALARM > > in8: +3.34 V (min = +3.18 V, max = +0.05 V) ALARM > > fan1: 0 RPM (min = 3515 RPM, div = 128) ALARM > > fan2: 1022 RPM (min = 1638 RPM, div = 8) ALARM > > fan3: 0 RPM (min = 958 RPM, div = 128) ALARM > > fan4: 0 RPM (min = 10546 RPM, div = 128) ALARM > > fan5: 0 RPM (min = 3515 RPM, div = 128) ALARM > > temp1: +30.0°C (high = -56.0°C, hyst = -17.0°C) ALARM sensor = > > thermistor > > temp2: +41.5°C (high = +80.0°C, hyst = +75.0°C) sensor = thermistor > > temp3: -3.0°C (high = +80.0°C, hyst = +75.0°C) sensor = thermistor > > cpu0_vid: +0.000 V > > These are all PC Health informations I could find in the BIOS: > > CPU Temp = 49°C > CPUFAN = 1692 RPM > Vcore = 1.232V > 3VCC = 3.360V > VTT 1.1V = 1.120V > PCH Voltage = 1.096V > IGD Voltage = toggles between 1.176V and 1.184V > VSB = 3.280V > VBAT = 3.344V > > The voltages are rather hard to match aren't they? Not at all. in1 is VTT 1.1V (+1.11 V vs 1.120V). in2 and in3 are 3VCC (+3.36 V vs 3.360V, hardwired so can't be wrong.) in4 is PCH Voltage (+1.10 V vs 1.096V). in5 is IGD Voltage (+1.18 V vs 1.176V/1.184V). in7 and in8 are VSB and VBAT respectively (values match perfectly and they are internally wired too.) The remaining pair is in0 for Vcore. The different value can be explained by your BIOS running the CPU at its max frequency while Linux runs it as a lower frequency (and voltage is scaled down at lower frequencies.) This also explains the different CPU temperature (most probably temp2) and fan speed (fan2), assuming there is some form of automatic fan speed control in place. The BIOS doesn't show any value which Linux doesn't, so I'd say we are fine. And you can use the following as your configuration file: chip "w83667hg-isa-0a10" # Voltages label in0 "Vcore" label in1 "Vtt" label in2 "AVCC" label in3 "+3.3V" label in4 "PCH" label in5 "IGD" label in7 "3VSB" label in8 "Vbat" set in1_min 1.1 * 0.95 set in1_max 1.1 * 1.05 set in2_min 3.3 * 0.90 set in2_max 3.3 * 1.10 set in3_min 3.3 * 0.90 set in3_max 3.3 * 1.10 set in4_min 1.1 * 0.95 set in4_max 1.1 * 1.05 set in7_min 3.3 * 0.90 set in7_max 3.3 * 1.10 set in8_min 3.0 * 0.90 set in8_max 3.0 * 1.10 # Fans ignore fan1 label fan2 "CPU Fan" ignore fan3 ignore fan4 ignore fan5 set fan2_min 800 # Temperatures label temp1 "M/B Temp" label temp2 "CPU Temp" ignore temp3 set temp1_max 55 set temp1_max_hyst 52 I'll add it to the wiki now for reference. -- Jean Delvare http://khali.linux-fr.org/wishlist.html _______________________________________________ lm-sensors mailing list lm-sensors@xxxxxxxxxxxxxx http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
