This series adds AR9003 support to ath9k, this 3rd series one final bug Felix found on the the AR_BufLen abstraction on the patch titled "ath9k_hw: Fill descriptor abstrations for AR9003". Its now fixed and don't have any other pending issues. Since the patches depend on some other ones we have no option but to resubmit. The all-in-one git am'able patch can be found here: http://bombadil.infradead.org/~mcgrof/patches/ath9k/2010/all-04-15-v1.patch sha1sum: cf0a362c75acd475de5e33e3400545e3d8f74e63 Felix Fietkau (14): ath9k_hw: add silicon revision macros for AR9300 ath9k_hw: add a macro for abstracting generic timer access ath9k_hw: fix a missing hex prefix for a register mask ath9k_hw: add simple register abstraction for some AR9300 registers ath9k_hw: add support for GPIO differences on AR9003 ath9k_hw: Add AR9003 PHY register definitions ath9k_hw: Set the channel on AR9003 ath9k_hw: Implement PLL control on AR9003 ath9k_hw: Implement spur mitigation on AR9003 ath9k_hw: Split off ANI control to the PHY ops ath9k: Add Rx EDMA support ath9k_hw: Split out the function for reading the noise floor ath9k_hw: move AR9280 PCI EEPROM fix to eeprom_def.c ath9k_hw: Update ath9k_hw_set_dma for AR9300 Luis R. Rodriguez (52): ath9k_hw: start building an abstraction layer for hardware routines ath9k_hw: AR9003 does not have AR_RC_AHB skip its setting ath9k_hw: remove wrapper ath9k_hw_write_regs() ath9k_hw: Move some RF ops to the private callbacks ath9k_hw: skip PLL initialization on AR9003 on Power-On-Reset ath9k_hw: add some comments for ath9k_set_power_network_sleep() ath9k_hw: add a private callback for PLL control computation ath9k_hw: Add AR9003 PHY support ath9k_hw: move init config and default after chip is up ath9k_hw: add the AR9003 ar9003_hw_macversion_supported() ath9k_hw: disable ANI for AR9003 ath9k: disable the MIB interrupt if ANI is disabled ath9k_hw: add common channel select helpers for ar900[23] ath9k_hw: split initvals.h by hardware family ath9k_hw: add initvals for the AR9003 hardware family ath9k_hw: add helpers for processing the AR9003 INI ath9k_hw: add all the AR9003 PHY callbacks ath9k_hw: add a helper for Power Amplifier calibration for AR9002 ath9k_hw: add a helper for the OLC tem compensation for AR9002 ath9k_hw: rename PA calib for AR9287 ath9k_hw: shift code for AR9280 OLC temp comp ath9k_hw: move the AR9280 OLC temp comp to its own helper ath9k_hw: simplify OLC temp compensation for AR9002 ath9k_hw: rename the PA calib routines to match their families ath9k_hw: rename getNoiseFloorThresh() to ath9k_hw_loadnf() ath9k_hw: move the cal AR9100 calibration settings ath9k_hw: split calib code by hardware families ath9k_hw: add the AR9003 ar9003_hw_init_cal callback ath9k_hw: add the config_pci_powersave AR9003 callback ath9k_hw: split the generic hardware code by hardware family ath9k_hw: move the cck channel 14 INI to the AR9002 hw code ath9k_hw: move TX/RX gain INI stuff to its own hardware family code ath9k_hw: abstract the AR_PHY_AGC_CONTROL register access ath9k_hw: abstract loading noisefloor ath9k_hw: fill in the callbacks for calibration for AR9003 ath9k_hw: complete AR9003 calibration ath9k_hw: rename eep_AR9287_ops to eep_ar9287_ops ath9k_hw: restore mac address reading logic ath9k_hw: add OFDM spur mitigation for AR9003 ath9k_hw: move the RF claim stuff to AR9002 hardware family ath9k_hw: add the AR9300 SREV hw name print ath9k_hw: add TX/RX gain register initialization for AR9003 ath9k_hw: skip asynch fifo enablement to AR9003 ath9k_hw: skip WEP aggregation enable code for AR9003 ath9k_hw: move AR9002 mac ops to its own file ath9k: add RXLP and RXHP to debugfs counters ath9k_hw: enable CRC check of descriptors for AR9003 ath9k_hw: set cwmin and cwmax to 0 for for AR9003 upon txq reset mac80211: add LDPC control flag ath9k_hw: add LDPC support for AR9003 ath9k: add LDPC support ath9k_hw: add the PCI ID for the first AR9300 device Senthil Balasubramanian (5): ath9k_hw: Add the PCI IDs for AR9300 and fill up the pci_id_tables ath9k_hw: update the chip tests for AR9003 ath9k_hw: prevent reset control register zeroing on AR9003 reset ath9k_hw: the eep_map is used only for AR9280 PCI card ini fixup ath9k_hw: Implement AR9003 eeprom callbacks Vasanthakumar Thiagarajan (26): ath9k_hw: Add hw cap flag for EDMA for the AR9003 family ath9k_hw: Fill few hw cap for edma ath9k_hw: Add abstraction for rx enable ath9k_hw: Fill rx_enable() for the AR9003 hardware family ath9k_hw: Add few routines for rx edma support ath9k_hw: Define tx control struct for AR9003 ath9k_hw: Move code which populates ds_data to ath9k_hw ath9k_hw: Add abstraction to set/get link pointer ath9k: Use abstraction to get link pointer ath9k: Use memcpy in ath_clone_txbuf() ath9k: Remove ATH9K_TX_SW_ABORTED and introduce a bool for this purpose ath9k: Make bf_desc of ath_buf opaque ath9k_hw: Abstract the routine which returns interrupt status ath9k_hw: Initialize interrupt mask for AR9003 ath9k_hw: Fill get_isr() for AR9003 ath9k_hw: Configure Tx interrupt mitigation timer ath9k: Load SW filtered NF values and start NF cal during full reset for AR9003 ath9k_hw: Define abstraction for tx desc access ath9k_hw: Add function to configure tx status ring buffer ath9k_hw: Fill descriptor abstrations for AR9003 ath9k: Setup appropriate tx desc for regular dma and edma ath9k: Initialize and configure tx status for EDMA ath9k_hw: Compute pointer checksum over the link descriptor ath9k: Add Tx EDMA support ath9k: Enable TXOK and TXERR interrupts for TX EDMA ath9k_hw: Abort rx if hw is not coming out of full sleep in reset drivers/net/wireless/ath/ath9k/Makefile | 16 +- drivers/net/wireless/ath/ath9k/ani.c | 185 +-- drivers/net/wireless/ath/ath9k/ar5008_initvals.h | 742 ++++++++ drivers/net/wireless/ath/ath9k/ar5008_phy.c | 1347 +++++++++++++ drivers/net/wireless/ath/ath9k/ar9001_initvals.h | 1254 +++++++++++++ drivers/net/wireless/ath/ath9k/ar9002_calib.c | 995 ++++++++++ drivers/net/wireless/ath/ath9k/ar9002_hw.c | 588 ++++++ .../ath/ath9k/{initvals.h => ar9002_initvals.h} | 1984 +------------------- drivers/net/wireless/ath/ath9k/ar9002_mac.c | 480 +++++ drivers/net/wireless/ath/ath9k/ar9002_phy.c | 534 ++++++ drivers/net/wireless/ath/ath9k/ar9002_phy.h | 572 ++++++ drivers/net/wireless/ath/ath9k/ar9003_calib.c | 802 ++++++++ drivers/net/wireless/ath/ath9k/ar9003_eeprom.c | 1856 ++++++++++++++++++ drivers/net/wireless/ath/ath9k/ar9003_eeprom.h | 323 ++++ drivers/net/wireless/ath/ath9k/ar9003_hw.c | 205 ++ drivers/net/wireless/ath/ath9k/ar9003_initvals.h | 1793 ++++++++++++++++++ drivers/net/wireless/ath/ath9k/ar9003_mac.c | 611 ++++++ drivers/net/wireless/ath/ath9k/ar9003_mac.h | 120 ++ drivers/net/wireless/ath/ath9k/ar9003_phy.c | 1142 +++++++++++ drivers/net/wireless/ath/ath9k/ar9003_phy.h | 847 +++++++++ drivers/net/wireless/ath/ath9k/ath9k.h | 24 +- drivers/net/wireless/ath/ath9k/beacon.c | 5 +- drivers/net/wireless/ath/ath9k/calib.c | 1089 +----------- drivers/net/wireless/ath/ath9k/calib.h | 19 +- drivers/net/wireless/ath/ath9k/common.h | 4 +- drivers/net/wireless/ath/ath9k/debug.c | 22 +- drivers/net/wireless/ath/ath9k/debug.h | 4 + drivers/net/wireless/ath/ath9k/eeprom.c | 9 +- drivers/net/wireless/ath/ath9k/eeprom.h | 22 +- drivers/net/wireless/ath/ath9k/eeprom_4k.c | 7 +- drivers/net/wireless/ath/ath9k/eeprom_9287.c | 9 +- drivers/net/wireless/ath/ath9k/eeprom_def.c | 13 +- drivers/net/wireless/ath/ath9k/hw-ops.h | 280 +++ drivers/net/wireless/ath/ath9k/hw.c | 1647 +++-------------- drivers/net/wireless/ath/ath9k/hw.h | 234 +++- drivers/net/wireless/ath/ath9k/init.c | 38 +- drivers/net/wireless/ath/ath9k/mac.c | 463 ++--- drivers/net/wireless/ath/ath9k/mac.h | 49 +- drivers/net/wireless/ath/ath9k/main.c | 51 +- drivers/net/wireless/ath/ath9k/pci.c | 1 + drivers/net/wireless/ath/ath9k/phy.c | 978 ---------- drivers/net/wireless/ath/ath9k/phy.h | 584 +------ drivers/net/wireless/ath/ath9k/rc.c | 9 + drivers/net/wireless/ath/ath9k/recv.c | 518 ++++-- drivers/net/wireless/ath/ath9k/reg.h | 167 ++- drivers/net/wireless/ath/ath9k/xmit.c | 365 +++- include/net/mac80211.h | 2 + 47 files changed, 16166 insertions(+), 6843 deletions(-) create mode 100644 drivers/net/wireless/ath/ath9k/ar5008_initvals.h create mode 100644 drivers/net/wireless/ath/ath9k/ar5008_phy.c create mode 100644 drivers/net/wireless/ath/ath9k/ar9001_initvals.h create mode 100644 drivers/net/wireless/ath/ath9k/ar9002_calib.c create mode 100644 drivers/net/wireless/ath/ath9k/ar9002_hw.c rename drivers/net/wireless/ath/ath9k/{initvals.h => ar9002_initvals.h} (79%) create mode 100644 drivers/net/wireless/ath/ath9k/ar9002_mac.c create mode 100644 drivers/net/wireless/ath/ath9k/ar9002_phy.c create mode 100644 drivers/net/wireless/ath/ath9k/ar9002_phy.h create mode 100644 drivers/net/wireless/ath/ath9k/ar9003_calib.c create mode 100644 drivers/net/wireless/ath/ath9k/ar9003_eeprom.c create mode 100644 drivers/net/wireless/ath/ath9k/ar9003_eeprom.h create mode 100644 drivers/net/wireless/ath/ath9k/ar9003_hw.c create mode 100644 drivers/net/wireless/ath/ath9k/ar9003_initvals.h create mode 100644 drivers/net/wireless/ath/ath9k/ar9003_mac.c create mode 100644 drivers/net/wireless/ath/ath9k/ar9003_mac.h create mode 100644 drivers/net/wireless/ath/ath9k/ar9003_phy.c create mode 100644 drivers/net/wireless/ath/ath9k/ar9003_phy.h create mode 100644 drivers/net/wireless/ath/ath9k/hw-ops.h delete mode 100644 drivers/net/wireless/ath/ath9k/phy.c -- To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
