I met the same problem before, if i modify the 1q header to other value (0xaa00) before go into firmware. I can capture the packet in the air I think the vlan packet is dropped in firmware. 2016-11-04 22:41 GMT+08:00 Bruno Antunes <baantunes@xxxxxxxxx>: > On 4 November 2016 at 14:18, Mauro Mozzarelli <openwrt@xxxxxxxxxxxx> wrote: >> Since the capability is implemented in software you might be testing the >> limit of your router's CPU i/o speed. > > By loading the module in rawmode? > > The AP is an APU and Sta is an APU2. > >> >> >> >> On 04/11/16 14:13, Bruno Antunes wrote: >>> >>> Hi all, >>> >>> Old thread but I think the issue is still present. >>> >>> I'm running a setup with VLANs with WDS and ath10k cards. >>> >>> To make it work both cards must be loaded in rawmode, AP >>> and Sta, and with no security. >>> >>> I'm using a OpenWrt trunk r49941 and the most recent firmware, >>> 10.2.4.70.58, from Kalle ath10k firmware tree. >>> >>> Although it works the throughput is very bad. >>> Are there any alternatives to improve the throughput. >>> >>> Best Regards, >>> Bruno >>> >>> On 9 December 2015 at 17:24, voncken <cedric.voncken@xxxxxxxxx> wrote: >>>> >>>> >>>>> -----Message d'origine----- >>>>> De : Ben Greear [mailto:greearb@xxxxxxxxxxxxxxx] >>>>> Envoyé : mercredi 9 décembre 2015 16:34 >>>>> À : Cedric VONCKEN; ath10k@xxxxxxxxxxxxxxxxxxx; linux-wireless >>>>> Objet : Re: ATH10K VLAN firmware issue >>>>> >>>>> This only happens when you use STA + WDS, or is .1q broken for you in >>>>> other cases as well? >>>> >>>> No, this issue occurs in all modes (STA, STA + WDS, AP). >>>> >>>> Thanks >>>> >>>> Cedric. >>>> >>>>> Thanks, >>>>> Ben >>>>> >>>>> On 12/08/2015 06:29 AM, Cedric VONCKEN wrote: >>>>>> >>>>>> I'm testing to transmit frame with 802.1q tag (VLAN). >>>>>> >>>>>> My client is set in STA + WDS and the netdev is bridged with eth0. >>>>>> I have a computer with vlan configuration set connected to the STA >>>>>> eth0. >>>>>> >>>>>> If I try to transmit frames with 802.1q tag, the frames are not >>>> >>>> sent. >>>>>> >>>>>> I checked with wireless sniffer, and I don't see the frame with >>>>>> VLAN >>>>>> tag (the frames without VLAN tag are sent). >>>>>> >>>>>> I tested with firmware 10.2.4.70.14-2 from kale github, >>>>>> 10.1.467-ct-com-full-015 from candelatech and 10.2.4.70-2 from >>>>>> openwrt, and in all cases I have the same issue. >>>>>> >>>>>> Thanks for your help. >>>>>> >>>>>> >>>>>> -- >>>>>> To unsubscribe from this list: send the line "unsubscribe >>>>>> linux-wireless" in the body of a message to majordomo@xxxxxxxxxxxxxxx >>>>>> More majordomo info at http://vger.kernel.org/majordomo-info.html >>>>>> >>>>> -- >>>>> Ben Greear <greearb@xxxxxxxxxxxxxxx> >>>>> Candela Technologies Inc http://www.candelatech.com >>>> >>>> -- >>>> To unsubscribe from this list: send the line "unsubscribe linux-wireless" >>>> in >>>> the body of a message to majordomo@xxxxxxxxxxxxxxx >>>> More majordomo info at http://vger.kernel.org/majordomo-info.html >>> >>> _______________________________________________ >>> openwrt-devel mailing list >>> openwrt-devel@xxxxxxxxxxxxxxxxx >>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel >> >> _______________________________________________ >> openwrt-devel mailing list >> openwrt-devel@xxxxxxxxxxxxxxxxx >> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel > > _______________________________________________ > ath10k mailing list > ath10k@xxxxxxxxxxxxxxxxxxx > http://lists.infradead.org/mailman/listinfo/ath10k
