I have tested borad-2.bin file with my module, by forcing ar->id.subsystem_vendor = 0x168c; ar->id.subsystem_device = 0x3363; (1,2,3) in ath/ath10k/pci.c file. All the tests failed with: ath10k_pci 0000:01:00.0: failed to receive initialized event from target: 00000000 ath10k_pci 0000:01:00.0: firmware crashed! (uuid 5506e81c-d538-4492-91d7-dc899fed8d8c) Does it mean, that this module is not supported? I will need to dump firmware from windows driver, when I get it from the vendor ? Thank you for the support 2015-12-01 10:53 GMT+01:00 Bartlomiej Grzeskowiak <bartlomiej.grzeskowiak@xxxxxxxxx>: > HI, > > Yes, I am testing it now: > > ath10k_pci 0000:01:00.0: boot get otp board id result 0x00000001 > board_id 0 chip_id 0 > ath10k_pci 0000:01:00.0: boot using board name > 'bus=pci,vendor=168c,device=003e,subsystem-vendor=0000,subsystem-device=0000' > ath10k_pci 0000:01:00.0: board name > ath10k_pci 0000:01:00.0: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 > 6f 72 3d 31 bus=pci,vendor=1 > ath10k_pci 0000:01:00.0: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 > 30 33 65 2c 68c,device=003e, > ath10k_pci 0000:01:00.0: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 > 6e 64 6f 72 subsystem-vendor > ath10k_pci 0000:01:00.0: 00000030: 3d 31 36 38 63 2c 73 75 62 73 79 73 > 74 65 6d 2d =168c,subsystem- > ath10k_pci 0000:01:00.0: 00000040: 64 65 76 69 63 65 3d 33 33 36 31 > device=3361 > ath10k_pci 0000:01:00.0: board name > ath10k_pci 0000:01:00.0: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 > 6f 72 3d 31 bus=pci,vendor=1 > ath10k_pci 0000:01:00.0: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 > 30 33 65 2c 68c,device=003e, > ath10k_pci 0000:01:00.0: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 > 6e 64 6f 72 subsystem-vendor > ath10k_pci 0000:01:00.0: 00000030: 3d 31 36 38 63 2c 73 75 62 73 79 73 > 74 65 6d 2d =168c,subsystem- > ath10k_pci 0000:01:00.0: 00000040: 64 65 76 69 63 65 3d 33 33 36 32 > device=3362 > ath10k_pci 0000:01:00.0: board name > ath10k_pci 0000:01:00.0: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 > 6f 72 3d 31 bus=pci,vendor=1 > ath10k_pci 0000:01:00.0: 00000010: 36 38 63 2c 64 65 76 69 63 65 3d 30 > 30 33 65 2c 68c,device=003e, > ath10k_pci 0000:01:00.0: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 > 6e 64 6f 72 subsystem-vendor > ath10k_pci 0000:01:00.0: 00000030: 3d 31 36 38 63 2c 73 75 62 73 79 73 > 74 65 6d 2d =168c,subsystem- > ath10k_pci 0000:01:00.0: 00000040: 64 65 76 69 63 65 3d 33 33 36 33 > device=3363 > ath10k_pci 0000:01:00.0: failed to fetch board data for > ath10k/QCA6174/hw3.0 from > bus=pci,vendor=168c,device=003e,subsystem-vendor=0000,subsystem-device=0000/board-2.bin, > board_len= 0, board_data= 0x0 > ath10k_pci 0000:01:00.0: failed to fetch board data > ath10k_pci 0000:01:00.0: failed to fetch board file: -2 > ath10k_pci 0000:01:00.0: boot hif power down > ath10k_pci 0000:01:00.0: could not probe fw (-2) > ath10k_pci 0000:01:00.0: pci ps timer refcount 0 awake 1 > ath10k_pci 0000:01:00.0: pci ps sleep reg refcount 0 awake 1 > > Strange that my card is subsystem-vendor=0000,subsystem-device=0000... > > 2015-12-01 10:43 GMT+01:00 Bartosz Markowski <bartosz.markowski@xxxxxxxxx>: >> On 1 December 2015 at 09:42, Michal Kazior <michal.kazior@xxxxxxxxx> wrote: >>> On 1 December 2015 at 09:38, Bartlomiej Grzeskowiak >>> <bartlomiej.grzeskowiak@xxxxxxxxx> wrote: >>>> Hi, >>>> >>>> I have already tried with backports 4.2.6 and different combinations >>>> of firmware.bin / board.bin. With differnt results, but none of them >>>> works. I will redo the tests and summarize them. >>>> >>>> Loading with irq_mode=1 gives me following result: >>>> [55416.824364] ath10k_pci 0000:01:00.0: limiting irq mode to: 1 >>>> [55416.830102] ath10k_pci 0000:01:00.0: pci irq legacy interrupts 0 >>>> irq_mode 1 reset_mode 0 >>>> [55417.212048] ath10k_pci 0000:01:00.0: could not fetch firmware file >>>> 'ath10k/QCA6174/hw3.0/firmware-5.bin': -2 >>>> [55424.394422] ath10k_pci 0000:01:00.0: wmi unified ready event not received >>>> [55424.436023] ath10k_pci 0000:01:00.0: firmware crashed! (uuid >>>> e082ac60-7c2d-4d14-9c49-fd5b0591c95c) >>>> [55424.445008] ath10k_pci 0000:01:00.0: qca6174 hw3.2 (0x05030000, >>> >>> Oh, wait. >>> >>> You have hw3.2? I haven't noticed that earlier. >>> >>> If memory serves right it needs a different board.bin (compared to >>> e.g. hw3.0). I'm not sure if it's available in Kalle's repository. >>> Wrong board.bin can cause firmware to hang or crash during init. >> >> Could you give a try to the board-2.bin file, which is sort of a >> container for the board bins, ath10k shall support.. and say if it >> solves your card problem? >> >> *) https://github.com/kvalo/ath10k-firmware/blob/master/QCA6174/hw3.0/board-2.bin >> >> -- >> Bartosz -- To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html