On Sun, Oct 21, 2012 at 06:03:24PM +0200, Ulrich Eckhardt wrote: > Hello, > > I have problems to get my USB3 cardreader to work reliably when > connected to the USB3 port. Due to lack of other USB3 devices I > don't know if it is the cardreader or the USB3 host (NEC uPD720200) > but the cardreader always works reliable when connected to USB2. > > Sometimes it is not possible to use the cardreader directly after > power up and I have to restart the computer. Very often the > cardreader stops working after removing a SD-card and insert another > SD-card or during copying data. > > I have tested it with Kernel 3.6.2. The USB3 port is the one built > in the Mainboard M4A87DT EVO. Did a previous kernel version work? > I saw, that the outputs of lspci are different, if there is a > problem directly after startup. Bjorn, can you take a look at this PCI output, and tell me if it matters that the host has bus master and latency 0 when it works and is missing those properties when it doesn't? Does the lspci differ when booting the same kernel, or is the lspci from two different kernels? > When the port is working: > 04:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host > Controller (rev 03) (prog-if 30 [XHCI]) > Subsystem: NEC Corporation uPD720200 USB 3.0 Host Controller > Flags: bus master, fast devsel, latency 0, IRQ 18 > Memory at f9efe000 (64-bit, non-prefetchable) [size=8K] > Capabilities: [50] Power Management version 3 > Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+ > Capabilities: [90] MSI-X: Enable+ Count=8 Masked- > Capabilities: [a0] Express Endpoint, MSI 00 > Capabilities: [100] Advanced Error Reporting > Capabilities: [140] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff > Capabilities: [150] Latency Tolerance Reporting > Kernel driver in use: xhci_hcd > > When the port is not working: > 04:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host > Controller (rev 03) (prog-if 30 [XHCI]) > Subsystem: NEC Corporation uPD720200 USB 3.0 Host Controller > Flags: fast devsel, IRQ 18 > Memory at f9efe000 (64-bit, non-prefetchable) [disabled][size=8K] > Capabilities: [50] Power Management version 3 > Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+ > Capabilities: [90] MSI-X: Enable- Count=8 Masked- > Capabilities: [a0] Express Endpoint, MSI 00 > Capabilities: [100] Advanced Error Reporting > Capabilities: [140] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff > Capabilities: [150] Latency Tolerance Reporting > > A dmesg output, when the cardreader stops after removing the SD-card: > [ 483.143351] hub 9-0:1.0: cannot reset port 2 (err = -19) > [ 483.143398] hub 9-0:1.0: hub_port_status failed (err = -19) > [ 483.143433] sd 10:0:0:4: Device offlined - not ready after error recovery > [ 586.083402] sdf: detected capacity change from 2032664576 to 0 > > > Here is a dmesg output, when the cardreader stops working during > copying data: Is there anything before that line in the dmesg? Because it seems that the whole xHCI host gets unregistered, and it would be good to know why. Sarah Sharp > [ 787.343581] usb 9-2: USB disconnect, device number 2 > [ 831.620551] xhci_hcd 0000:04:00.0: remove, state 4 > [ 831.620604] usb usb9: USB disconnect, device number 1 > [ 831.620742] xHCI xhci_drop_endpoint called for root hub > [ 831.620746] xHCI xhci_check_bandwidth called for root hub > [ 831.629149] xhci_hcd 0000:04:00.0: USB bus 9 deregistered > [ 831.629182] xhci_hcd 0000:04:00.0: remove, state 4 > [ 831.629192] usb usb8: USB disconnect, device number 1 > [ 831.629284] xHCI xhci_drop_endpoint called for root hub > [ 831.629287] xHCI xhci_check_bandwidth called for root hub > [ 831.733941] xhci_hcd 0000:04:00.0: USB bus 8 deregistered > [ 833.765457] xhci_hcd 0000:04:00.0: xHCI Host Controller > [ 833.765484] xhci_hcd 0000:04:00.0: new USB bus registered, > assigned bus number 8 > [ 833.869813] xhci_hcd 0000:04:00.0: irq 18, io mem 0xf9efe000 > [ 833.869893] xhci_hcd 0000:04:00.0: irq 46 for MSI/MSI-X > [ 833.869909] xhci_hcd 0000:04:00.0: irq 47 for MSI/MSI-X > [ 833.869925] xhci_hcd 0000:04:00.0: irq 48 for MSI/MSI-X > [ 833.869940] xhci_hcd 0000:04:00.0: irq 49 for MSI/MSI-X > [ 833.869954] xhci_hcd 0000:04:00.0: irq 50 for MSI/MSI-X > [ 833.869969] xhci_hcd 0000:04:00.0: irq 51 for MSI/MSI-X > [ 833.869983] xhci_hcd 0000:04:00.0: irq 52 for MSI/MSI-X > [ 833.870170] usb usb8: New USB device found, idVendor=1d6b, idProduct=0002 > [ 833.870177] usb usb8: New USB device strings: Mfr=3, Product=2, > SerialNumber=1 > [ 833.870183] usb usb8: Product: xHCI Host Controller > [ 833.870188] usb usb8: Manufacturer: Linux 3.6.2-ue-desktop xhci_hcd > [ 833.870192] usb usb8: SerialNumber: 0000:04:00.0 > [ 833.870430] xHCI xhci_add_endpoint called for root hub > [ 833.870435] xHCI xhci_check_bandwidth called for root hub > [ 833.870503] hub 8-0:1.0: USB hub found > [ 833.870515] hub 8-0:1.0: 2 ports detected > [ 833.900727] xhci_hcd 0000:04:00.0: xHCI Host Controller > [ 833.900743] xhci_hcd 0000:04:00.0: new USB bus registered, > assigned bus number 9 > [ 833.900811] usb usb9: New USB device found, idVendor=1d6b, idProduct=0003 > [ 833.900818] usb usb9: New USB device strings: Mfr=3, Product=2, > SerialNumber=1 > [ 833.900823] usb usb9: Product: xHCI Host Controller > [ 833.900828] usb usb9: Manufacturer: Linux 3.6.2-ue-desktop xhci_hcd > [ 833.900833] usb usb9: SerialNumber: 0000:04:00.0 > [ 833.901058] xHCI xhci_add_endpoint called for root hub > [ 833.901062] xHCI xhci_check_bandwidth called for root hub > [ 833.901129] hub 9-0:1.0: USB hub found > [ 833.901145] hub 9-0:1.0: 2 ports detected > [ 834.207292] usb 9-2: new SuperSpeed USB device number 2 using xhci_hcd > [ 834.226262] usb 9-2: Parent hub missing LPM exit latency info. > Power management will be impacted. > [ 834.323600] usb 9-2: New USB device found, idVendor=0bda, idProduct=0301 > [ 834.323611] usb 9-2: New USB device strings: Mfr=1, Product=2, > SerialNumber=3 > [ 834.323617] usb 9-2: Product: USB3.0 Card Reader > [ 834.323622] usb 9-2: Manufacturer: Realtek > [ 834.323627] usb 9-2: SerialNumber: 201006010301 > [ 834.330317] scsi11 : usb-storage 9-2:1.0 > [ 835.347621] scsi 11:0:0:0: Direct-Access Generic- USB3.0 > CRW-CF/MD 1.00 PQ: 0 ANSI: 0 CCS > [ 835.363575] scsi 11:0:0:1: Direct-Access Generic- USB3.0 > CRW-SM/xD 1.00 PQ: 0 ANSI: 0 CCS > [ 835.379999] scsi 11:0:0:2: Direct-Access Generic- USB3.0 > CRW-SD 1.00 PQ: 0 ANSI: 0 CCS > [ 835.396476] scsi 11:0:0:3: Direct-Access Generic- USB3.0 > CRW-MS 1.00 PQ: 0 ANSI: 0 CCS > [ 835.412459] scsi 11:0:0:4: Direct-Access Generic- USB3.0 > CRW-SD/MS 1.00 PQ: 0 ANSI: 0 CCS > [ 835.414504] sd 11:0:0:0: Attached scsi generic sg4 type 0 > [ 835.414809] sd 11:0:0:1: Attached scsi generic sg5 type 0 > [ 835.415100] sd 11:0:0:2: Attached scsi generic sg6 type 0 > [ 835.415319] sd 11:0:0:3: Attached scsi generic sg7 type 0 > [ 835.415514] sd 11:0:0:4: Attached scsi generic sg8 type 0 > [ 835.644755] sd 11:0:0:2: [sdf] Attached SCSI removable disk > [ 835.649335] sd 11:0:0:4: [sdh] Attached SCSI removable disk > [ 835.661916] sd 11:0:0:1: [sde] Attached SCSI removable disk > [ 835.670545] sd 11:0:0:0: [sdd] Attached SCSI removable disk > [ 835.674558] sd 11:0:0:3: [sdg] Attached SCSI removable disk > [ 844.984896] sd 11:0:0:2: [sdf] 3970048 512-byte logical blocks: > (2.03 GB/1.89 GiB) > [ 844.986038] sd 11:0:0:2: [sdf] No Caching mode page present > [ 844.986049] sd 11:0:0:2: [sdf] Assuming drive cache: write through > [ 844.989503] sd 11:0:0:2: [sdf] No Caching mode page present > [ 844.989513] sd 11:0:0:2: [sdf] Assuming drive cache: write through > [ 844.991736] sdf: sdf1 > [ 912.223693] Clocksource tsc unstable (delta = -128663206 ns) > [ 912.223700] hub 9-0:1.0: cannot reset port 2 (err = -19) > [ 912.223772] Switching to clocksource hpet > [ 912.485117] sd 11:0:0:2: Device offlined - not ready after error recovery > [ 912.485128] sd 11:0:0:2: [sdf] Unhandled error code > [ 912.485129] sd 11:0:0:2: [sdf] > [ 912.485131] Result: hostbyte=DID_ABORT driverbyte=DRIVER_OK > [ 912.485132] sd 11:0:0:2: [sdf] CDB: > [ 912.485133] Read(10): 28 00 00 34 c7 80 00 00 f0 00 > [ 912.485139] end_request: I/O error, dev sdf, sector 3458944 > [ 912.485169] sd 11:0:0:2: rejecting I/O to offline device > [ 912.485172] sd 11:0:0:2: killing request > [ 912.485193] sd 11:0:0:2: rejecting I/O to offline device > [ 912.485194] sd 11:0:0:2: [sdf] killing request > [ 912.485199] sd 11:0:0:2: rejecting I/O to offline device > [ 912.485206] sd 11:0:0:2: rejecting I/O to offline device > [ 912.485208] sd 11:0:0:2: rejecting I/O to offline device > [ 912.485215] sd 11:0:0:2: [sdf] Unhandled error code > [ 912.485217] sd 11:0:0:2: [sdf] > [ 912.485218] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK > [ 912.485220] sd 11:0:0:2: [sdf] CDB: > [ 912.485221] Read(10): 28 00 00 34 c8 70 00 00 10 00 > [ 912.485231] end_request: I/O error, dev sdf, sector 3459184 > [ 912.485249] sd 11:0:0:2: rejecting I/O to offline device > [ 912.485439] hub 9-0:1.0: hub_port_status failed (err = -19) > [ 912.493691] sd 11:0:0:2: rejecting I/O to offline device > > > The lsusb-output of the Cardreader from Delock > lsusb -v -s 9: > > Bus 009 Device 002: ID 0bda:0301 Realtek Semiconductor Corp. > Device Descriptor: > bLength 18 > bDescriptorType 1 > bcdUSB 3.00 > bDeviceClass 0 (Defined at Interface level) > bDeviceSubClass 0 > bDeviceProtocol 0 > bMaxPacketSize0 9 > idVendor 0x0bda Realtek Semiconductor Corp. > idProduct 0x0301 > bcdDevice 1.20 > iManufacturer 1 Realtek > iProduct 2 USB3.0 Card Reader > iSerial 3 201006010301 > bNumConfigurations 1 > Configuration Descriptor: > bLength 9 > bDescriptorType 2 > wTotalLength 44 > bNumInterfaces 1 > bConfigurationValue 1 > iConfiguration 4 CARD READER > bmAttributes 0x80 > (Bus Powered) > MaxPower 200mA > Interface Descriptor: > bLength 9 > bDescriptorType 4 > bInterfaceNumber 0 > bAlternateSetting 0 > bNumEndpoints 2 > bInterfaceClass 8 Mass Storage > bInterfaceSubClass 6 SCSI > bInterfaceProtocol 80 Bulk (Zip) > iInterface 5 Bulk-In, Bulk-Out, Interface > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x01 EP 1 OUT > bmAttributes 2 > Transfer Type Bulk > Synch Type None > Usage Type Data > wMaxPacketSize 0x0400 1x 1024 bytes > bInterval 0 > bMaxBurst 3 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x82 EP 2 IN > bmAttributes 2 > Transfer Type Bulk > Synch Type None > Usage Type Data > wMaxPacketSize 0x0400 1x 1024 bytes > bInterval 0 > bMaxBurst 3 > inary Object Store Descriptor: > bLength 5 > bDescriptorType 15 > wTotalLength 22 > bNumDeviceCaps 2 > USB 2.0 Extension Device Capability: > bLength 7 > bDescriptorType 16 > bDevCapabilityType 2 > bmAttributes 0x00000002 > Link Power Management (LPM) Supported > SuperSpeed USB Device Capability: > bLength 10 > bDescriptorType 16 > bDevCapabilityType 3 > bmAttributes 0x00 > Latency Tolerance Messages (LTM) Supported > wSpeedsSupported 0x000e > Device can operate at Full Speed (12Mbps) > Device can operate at High Speed (480Mbps) > Device can operate at SuperSpeed (5Gbps) > bFunctionalitySupport 0 > Lowest fully-functional device speed is Low Speed (1Mbps) > bU1DevExitLat 1 micro seconds > bU2DevExitLat 2815 micro seconds > Device Status: 0x0000 > (Bus Powered) > Bus 009 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub > Device Descriptor: > bLength 18 > bDescriptorType 1 > bcdUSB 3.00 > bDeviceClass 9 Hub > bDeviceSubClass 0 Unused > bDeviceProtocol 3 > bMaxPacketSize0 9 > idVendor 0x1d6b Linux Foundation > idProduct 0x0003 3.0 root hub > bcdDevice 3.06 > iManufacturer 3 Linux 3.6.2-ue-desktop xhci_hcd > iProduct 2 xHCI Host Controller > iSerial 1 0000:04:00.0 > bNumConfigurations 1 > Configuration Descriptor: > bLength 9 > bDescriptorType 2 > wTotalLength 31 > bNumInterfaces 1 > bConfigurationValue 1 > iConfiguration 0 > bmAttributes 0xe0 > Self Powered > Remote Wakeup > MaxPower 0mA > Interface Descriptor: > bLength 9 > bDescriptorType 4 > bInterfaceNumber 0 > bAlternateSetting 0 > bNumEndpoints 1 > bInterfaceClass 9 Hub > bInterfaceSubClass 0 Unused > bInterfaceProtocol 0 Full speed (or root) hub > iInterface 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x81 EP 1 IN > bmAttributes 3 > Transfer Type Interrupt > Synch Type None > Usage Type Data > wMaxPacketSize 0x0004 1x 4 bytes > bInterval 12 > bMaxBurst 0 > Hub Descriptor: > bLength 12 > bDescriptorType 42 > nNbrPorts 2 > wHubCharacteristic 0x0009 > Per-port power switching > Per-port overcurrent protection > bPwrOn2PwrGood 10 * 2 milli seconds > bHubContrCurrent 0 milli Ampere > bHubDecLat 0.0 micro seconds > wHubDelay 0 nano seconds > DeviceRemovable 0x00 > Hub Port Status: > Port 1: 0000.02a0 5Gbps power Rx.Detect > Port 2: 0000.0203 5Gbps power U0 enable connect > Binary Object Store Descriptor: > bLength 5 > bDescriptorType 15 > wTotalLength 15 > bNumDeviceCaps 1 > SuperSpeed USB Device Capability: > bLength 10 > bDescriptorType 16 > bDevCapabilityType 3 > bmAttributes 0x02 > wSpeedsSupported 0x0008 > Device can operate at SuperSpeed (5Gbps) > bFunctionalitySupport 0 > Lowest fully-functional device speed is Low Speed (1Mbps) > bU1DevExitLat 3 micro seconds > bU2DevExitLat 0 micro seconds > Device Status: 0x0001 > Self Powered > > An output of lspci of my system: > lspci > 00:00.0 Host bridge: Advanced Micro Devices [AMD] nee ATI > RX780/RX790 Chipset Host Bridge > 00:02.0 PCI bridge: Advanced Micro Devices [AMD] nee ATI RD790 PCI > to PCI bridge (external gfx0 port A) > 00:09.0 PCI bridge: Advanced Micro Devices [AMD] nee ATI RD790 PCI > to PCI bridge (PCI express gpp port E) > 00:0a.0 PCI bridge: Advanced Micro Devices [AMD] nee ATI RD790 PCI > to PCI bridge (PCI express gpp port F) > 00:11.0 SATA controller: Advanced Micro Devices [AMD] nee ATI > SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] (rev 40) > 00:12.0 USB controller: Advanced Micro Devices [AMD] nee ATI > SB7x0/SB8x0/SB9x0 USB OHCI0 Controller > 00:12.2 USB controller: Advanced Micro Devices [AMD] nee ATI > SB7x0/SB8x0/SB9x0 USB EHCI Controller > 00:13.0 USB controller: Advanced Micro Devices [AMD] nee ATI > SB7x0/SB8x0/SB9x0 USB OHCI0 Controller > 00:13.2 USB controller: Advanced Micro Devices [AMD] nee ATI > SB7x0/SB8x0/SB9x0 USB EHCI Controller > 00:14.0 SMBus: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus > Controller (rev 41) > 00:14.2 Audio device: Advanced Micro Devices [AMD] nee ATI SBx00 > Azalia (Intel HDA) (rev 40) > 00:14.3 ISA bridge: Advanced Micro Devices [AMD] nee ATI > SB7x0/SB8x0/SB9x0 LPC host controller (rev 40) > 00:14.4 PCI bridge: Advanced Micro Devices [AMD] nee ATI SBx00 PCI > to PCI Bridge (rev 40) > 00:14.5 USB controller: Advanced Micro Devices [AMD] nee ATI > SB7x0/SB8x0/SB9x0 USB OHCI2 Controller > 00:15.0 PCI bridge: Advanced Micro Devices [AMD] nee ATI > SB700/SB800/SB900 PCI to PCI bridge (PCIE port 0) > 00:15.1 PCI bridge: Advanced Micro Devices [AMD] nee ATI > SB700/SB800/SB900 PCI to PCI bridge (PCIE port 1) > 00:16.0 USB controller: Advanced Micro Devices [AMD] nee ATI > SB7x0/SB8x0/SB9x0 USB OHCI0 Controller > 00:16.2 USB controller: Advanced Micro Devices [AMD] nee ATI > SB7x0/SB8x0/SB9x0 USB EHCI Controller > 00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 10h > Processor HyperTransport Configuration > 00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 10h > Processor Address Map > 00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 10h > Processor DRAM Controller > 00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 10h > Processor Miscellaneous Control > 00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 10h > Processor Link Control > 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. > RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) > 02:00.0 Multimedia video controller: Conexant Systems, Inc. CX23885 > PCI Video and Audio Decoder (rev 02) > 04:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host > Controller (rev ff) > 05:00.0 SATA controller: JMicron Technology Corp. JMB361 AHCI/IDE (rev 02) > 05:00.1 IDE interface: JMicron Technology Corp. JMB361 AHCI/IDE (rev 02) > 06:00.0 VGA compatible controller: NVIDIA Corporation G98 [GeForce > 8400 GS] (rev a1) > > lsusb > Bus 001 Device 002: ID 0451:8042 Texas Instruments, Inc. > Bus 009 Device 002: ID 0bda:0301 Realtek Semiconductor Corp. > Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub > Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub > Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub > Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub > Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub > Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub > Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub > Bus 008 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub > Bus 009 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub > Bus 001 Device 003: ID 046d:c050 Logitech, Inc. RX 250 Optical Mouse > > > > -- > Ulrich Eckhardt http://www.uli-eckhardt.de > > Ein Blitzableiter auf dem Kirchturm ist das denkbar stärkste > Misstrauensvotum gegen den lieben Gott. (Karl Krauss) > -- > To unsubscribe from this list: send the line "unsubscribe linux-usb" in > the body of a message to majordomo@xxxxxxxxxxxxxxx > More majordomo info at http://vger.kernel.org/majordomo-info.html -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
