Hello,
I have problems to get my USB3 cardreader to work reliably when
connected to the USB3 port. Due to lack of other USB3 devices I don't
know if it is the cardreader or the USB3 host (NEC uPD720200) but the
cardreader always works reliable when connected to USB2.
Sometimes it is not possible to use the cardreader directly after power
up and I have to restart the computer. Very often the cardreader stops
working after removing a SD-card and insert another SD-card or during
copying data.
I have tested it with Kernel 3.6.2. The USB3 port is the one built in
the Mainboard M4A87DT EVO.
I saw, that the outputs of lspci are different, if there is a problem
directly after startup.
When the port is working:
04:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host
Controller (rev 03) (prog-if 30 [XHCI])
Subsystem: NEC Corporation uPD720200 USB 3.0 Host Controller
Flags: bus master, fast devsel, latency 0, IRQ 18
Memory at f9efe000 (64-bit, non-prefetchable) [size=8K]
Capabilities: [50] Power Management version 3
Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+
Capabilities: [90] MSI-X: Enable+ Count=8 Masked-
Capabilities: [a0] Express Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff
Capabilities: [150] Latency Tolerance Reporting
Kernel driver in use: xhci_hcd
When the port is not working:
04:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host
Controller (rev 03) (prog-if 30 [XHCI])
Subsystem: NEC Corporation uPD720200 USB 3.0 Host Controller
Flags: fast devsel, IRQ 18
Memory at f9efe000 (64-bit, non-prefetchable) [disabled][size=8K]
Capabilities: [50] Power Management version 3
Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+
Capabilities: [90] MSI-X: Enable- Count=8 Masked-
Capabilities: [a0] Express Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff
Capabilities: [150] Latency Tolerance Reporting
A dmesg output, when the cardreader stops after removing the SD-card:
[ 483.143351] hub 9-0:1.0: cannot reset port 2 (err = -19)
[ 483.143398] hub 9-0:1.0: hub_port_status failed (err = -19)
[ 483.143433] sd 10:0:0:4: Device offlined - not ready after error recovery
[ 586.083402] sdf: detected capacity change from 2032664576 to 0
Here is a dmesg output, when the cardreader stops working during copying
data:
[ 787.343581] usb 9-2: USB disconnect, device number 2
[ 831.620551] xhci_hcd 0000:04:00.0: remove, state 4
[ 831.620604] usb usb9: USB disconnect, device number 1
[ 831.620742] xHCI xhci_drop_endpoint called for root hub
[ 831.620746] xHCI xhci_check_bandwidth called for root hub
[ 831.629149] xhci_hcd 0000:04:00.0: USB bus 9 deregistered
[ 831.629182] xhci_hcd 0000:04:00.0: remove, state 4
[ 831.629192] usb usb8: USB disconnect, device number 1
[ 831.629284] xHCI xhci_drop_endpoint called for root hub
[ 831.629287] xHCI xhci_check_bandwidth called for root hub
[ 831.733941] xhci_hcd 0000:04:00.0: USB bus 8 deregistered
[ 833.765457] xhci_hcd 0000:04:00.0: xHCI Host Controller
[ 833.765484] xhci_hcd 0000:04:00.0: new USB bus registered, assigned
bus number 8
[ 833.869813] xhci_hcd 0000:04:00.0: irq 18, io mem 0xf9efe000
[ 833.869893] xhci_hcd 0000:04:00.0: irq 46 for MSI/MSI-X
[ 833.869909] xhci_hcd 0000:04:00.0: irq 47 for MSI/MSI-X
[ 833.869925] xhci_hcd 0000:04:00.0: irq 48 for MSI/MSI-X
[ 833.869940] xhci_hcd 0000:04:00.0: irq 49 for MSI/MSI-X
[ 833.869954] xhci_hcd 0000:04:00.0: irq 50 for MSI/MSI-X
[ 833.869969] xhci_hcd 0000:04:00.0: irq 51 for MSI/MSI-X
[ 833.869983] xhci_hcd 0000:04:00.0: irq 52 for MSI/MSI-X
[ 833.870170] usb usb8: New USB device found, idVendor=1d6b, idProduct=0002
[ 833.870177] usb usb8: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 833.870183] usb usb8: Product: xHCI Host Controller
[ 833.870188] usb usb8: Manufacturer: Linux 3.6.2-ue-desktop xhci_hcd
[ 833.870192] usb usb8: SerialNumber: 0000:04:00.0
[ 833.870430] xHCI xhci_add_endpoint called for root hub
[ 833.870435] xHCI xhci_check_bandwidth called for root hub
[ 833.870503] hub 8-0:1.0: USB hub found
[ 833.870515] hub 8-0:1.0: 2 ports detected
[ 833.900727] xhci_hcd 0000:04:00.0: xHCI Host Controller
[ 833.900743] xhci_hcd 0000:04:00.0: new USB bus registered, assigned
bus number 9
[ 833.900811] usb usb9: New USB device found, idVendor=1d6b, idProduct=0003
[ 833.900818] usb usb9: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 833.900823] usb usb9: Product: xHCI Host Controller
[ 833.900828] usb usb9: Manufacturer: Linux 3.6.2-ue-desktop xhci_hcd
[ 833.900833] usb usb9: SerialNumber: 0000:04:00.0
[ 833.901058] xHCI xhci_add_endpoint called for root hub
[ 833.901062] xHCI xhci_check_bandwidth called for root hub
[ 833.901129] hub 9-0:1.0: USB hub found
[ 833.901145] hub 9-0:1.0: 2 ports detected
[ 834.207292] usb 9-2: new SuperSpeed USB device number 2 using xhci_hcd
[ 834.226262] usb 9-2: Parent hub missing LPM exit latency info. Power
management will be impacted.
[ 834.323600] usb 9-2: New USB device found, idVendor=0bda, idProduct=0301
[ 834.323611] usb 9-2: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[ 834.323617] usb 9-2: Product: USB3.0 Card Reader
[ 834.323622] usb 9-2: Manufacturer: Realtek
[ 834.323627] usb 9-2: SerialNumber: 201006010301
[ 834.330317] scsi11 : usb-storage 9-2:1.0
[ 835.347621] scsi 11:0:0:0: Direct-Access Generic- USB3.0
CRW-CF/MD 1.00 PQ: 0 ANSI: 0 CCS
[ 835.363575] scsi 11:0:0:1: Direct-Access Generic- USB3.0
CRW-SM/xD 1.00 PQ: 0 ANSI: 0 CCS
[ 835.379999] scsi 11:0:0:2: Direct-Access Generic- USB3.0 CRW-SD
1.00 PQ: 0 ANSI: 0 CCS
[ 835.396476] scsi 11:0:0:3: Direct-Access Generic- USB3.0 CRW-MS
1.00 PQ: 0 ANSI: 0 CCS
[ 835.412459] scsi 11:0:0:4: Direct-Access Generic- USB3.0
CRW-SD/MS 1.00 PQ: 0 ANSI: 0 CCS
[ 835.414504] sd 11:0:0:0: Attached scsi generic sg4 type 0
[ 835.414809] sd 11:0:0:1: Attached scsi generic sg5 type 0
[ 835.415100] sd 11:0:0:2: Attached scsi generic sg6 type 0
[ 835.415319] sd 11:0:0:3: Attached scsi generic sg7 type 0
[ 835.415514] sd 11:0:0:4: Attached scsi generic sg8 type 0
[ 835.644755] sd 11:0:0:2: [sdf] Attached SCSI removable disk
[ 835.649335] sd 11:0:0:4: [sdh] Attached SCSI removable disk
[ 835.661916] sd 11:0:0:1: [sde] Attached SCSI removable disk
[ 835.670545] sd 11:0:0:0: [sdd] Attached SCSI removable disk
[ 835.674558] sd 11:0:0:3: [sdg] Attached SCSI removable disk
[ 844.984896] sd 11:0:0:2: [sdf] 3970048 512-byte logical blocks: (2.03
GB/1.89 GiB)
[ 844.986038] sd 11:0:0:2: [sdf] No Caching mode page present
[ 844.986049] sd 11:0:0:2: [sdf] Assuming drive cache: write through
[ 844.989503] sd 11:0:0:2: [sdf] No Caching mode page present
[ 844.989513] sd 11:0:0:2: [sdf] Assuming drive cache: write through
[ 844.991736] sdf: sdf1
[ 912.223693] Clocksource tsc unstable (delta = -128663206 ns)
[ 912.223700] hub 9-0:1.0: cannot reset port 2 (err = -19)
[ 912.223772] Switching to clocksource hpet
[ 912.485117] sd 11:0:0:2: Device offlined - not ready after error recovery
[ 912.485128] sd 11:0:0:2: [sdf] Unhandled error code
[ 912.485129] sd 11:0:0:2: [sdf]
[ 912.485131] Result: hostbyte=DID_ABORT driverbyte=DRIVER_OK
[ 912.485132] sd 11:0:0:2: [sdf] CDB:
[ 912.485133] Read(10): 28 00 00 34 c7 80 00 00 f0 00
[ 912.485139] end_request: I/O error, dev sdf, sector 3458944
[ 912.485169] sd 11:0:0:2: rejecting I/O to offline device
[ 912.485172] sd 11:0:0:2: killing request
[ 912.485193] sd 11:0:0:2: rejecting I/O to offline device
[ 912.485194] sd 11:0:0:2: [sdf] killing request
[ 912.485199] sd 11:0:0:2: rejecting I/O to offline device
[ 912.485206] sd 11:0:0:2: rejecting I/O to offline device
[ 912.485208] sd 11:0:0:2: rejecting I/O to offline device
[ 912.485215] sd 11:0:0:2: [sdf] Unhandled error code
[ 912.485217] sd 11:0:0:2: [sdf]
[ 912.485218] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[ 912.485220] sd 11:0:0:2: [sdf] CDB:
[ 912.485221] Read(10): 28 00 00 34 c8 70 00 00 10 00
[ 912.485231] end_request: I/O error, dev sdf, sector 3459184
[ 912.485249] sd 11:0:0:2: rejecting I/O to offline device
[ 912.485439] hub 9-0:1.0: hub_port_status failed (err = -19)
[ 912.493691] sd 11:0:0:2: rejecting I/O to offline device
The lsusb-output of the Cardreader from Delock
lsusb -v -s 9:
Bus 009 Device 002: ID 0bda:0301 Realtek Semiconductor Corp.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 3.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 9
idVendor 0x0bda Realtek Semiconductor Corp.
idProduct 0x0301
bcdDevice 1.20
iManufacturer 1 Realtek
iProduct 2 USB3.0 Card Reader
iSerial 3 201006010301
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 44
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 4 CARD READER
bmAttributes 0x80
(Bus Powered)
MaxPower 200mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk (Zip)
iInterface 5 Bulk-In, Bulk-Out, Interface
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 3
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 3
inary Object Store Descriptor:
bLength 5
bDescriptorType 15
wTotalLength 22
bNumDeviceCaps 2
USB 2.0 Extension Device Capability:
bLength 7
bDescriptorType 16
bDevCapabilityType 2
bmAttributes 0x00000002
Link Power Management (LPM) Supported
SuperSpeed USB Device Capability:
bLength 10
bDescriptorType 16
bDevCapabilityType 3
bmAttributes 0x00
Latency Tolerance Messages (LTM) Supported
wSpeedsSupported 0x000e
Device can operate at Full Speed (12Mbps)
Device can operate at High Speed (480Mbps)
Device can operate at SuperSpeed (5Gbps)
bFunctionalitySupport 0
Lowest fully-functional device speed is Low Speed (1Mbps)
bU1DevExitLat 1 micro seconds
bU2DevExitLat 2815 micro seconds
Device Status: 0x0000
(Bus Powered)
Bus 009 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 3.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 3
bMaxPacketSize0 9
idVendor 0x1d6b Linux Foundation
idProduct 0x0003 3.0 root hub
bcdDevice 3.06
iManufacturer 3 Linux 3.6.2-ue-desktop xhci_hcd
iProduct 2 xHCI Host Controller
iSerial 1 0000:04:00.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 31
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
bMaxBurst 0
Hub Descriptor:
bLength 12
bDescriptorType 42
nNbrPorts 2
wHubCharacteristic 0x0009
Per-port power switching
Per-port overcurrent protection
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
bHubDecLat 0.0 micro seconds
wHubDelay 0 nano seconds
DeviceRemovable 0x00
Hub Port Status:
Port 1: 0000.02a0 5Gbps power Rx.Detect
Port 2: 0000.0203 5Gbps power U0 enable connect
Binary Object Store Descriptor:
bLength 5
bDescriptorType 15
wTotalLength 15
bNumDeviceCaps 1
SuperSpeed USB Device Capability:
bLength 10
bDescriptorType 16
bDevCapabilityType 3
bmAttributes 0x02
wSpeedsSupported 0x0008
Device can operate at SuperSpeed (5Gbps)
bFunctionalitySupport 0
Lowest fully-functional device speed is Low Speed (1Mbps)
bU1DevExitLat 3 micro seconds
bU2DevExitLat 0 micro seconds
Device Status: 0x0001
Self Powered
An output of lspci of my system:
lspci
00:00.0 Host bridge: Advanced Micro Devices [AMD] nee ATI RX780/RX790
Chipset Host Bridge
00:02.0 PCI bridge: Advanced Micro Devices [AMD] nee ATI RD790 PCI to
PCI bridge (external gfx0 port A)
00:09.0 PCI bridge: Advanced Micro Devices [AMD] nee ATI RD790 PCI to
PCI bridge (PCI express gpp port E)
00:0a.0 PCI bridge: Advanced Micro Devices [AMD] nee ATI RD790 PCI to
PCI bridge (PCI express gpp port F)
00:11.0 SATA controller: Advanced Micro Devices [AMD] nee ATI
SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] (rev 40)
00:12.0 USB controller: Advanced Micro Devices [AMD] nee ATI
SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
00:12.2 USB controller: Advanced Micro Devices [AMD] nee ATI
SB7x0/SB8x0/SB9x0 USB EHCI Controller
00:13.0 USB controller: Advanced Micro Devices [AMD] nee ATI
SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
00:13.2 USB controller: Advanced Micro Devices [AMD] nee ATI
SB7x0/SB8x0/SB9x0 USB EHCI Controller
00:14.0 SMBus: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus
Controller (rev 41)
00:14.2 Audio device: Advanced Micro Devices [AMD] nee ATI SBx00 Azalia
(Intel HDA) (rev 40)
00:14.3 ISA bridge: Advanced Micro Devices [AMD] nee ATI
SB7x0/SB8x0/SB9x0 LPC host controller (rev 40)
00:14.4 PCI bridge: Advanced Micro Devices [AMD] nee ATI SBx00 PCI to
PCI Bridge (rev 40)
00:14.5 USB controller: Advanced Micro Devices [AMD] nee ATI
SB7x0/SB8x0/SB9x0 USB OHCI2 Controller
00:15.0 PCI bridge: Advanced Micro Devices [AMD] nee ATI
SB700/SB800/SB900 PCI to PCI bridge (PCIE port 0)
00:15.1 PCI bridge: Advanced Micro Devices [AMD] nee ATI
SB700/SB800/SB900 PCI to PCI bridge (PCIE port 1)
00:16.0 USB controller: Advanced Micro Devices [AMD] nee ATI
SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
00:16.2 USB controller: Advanced Micro Devices [AMD] nee ATI
SB7x0/SB8x0/SB9x0 USB EHCI Controller
00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor
HyperTransport Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor
Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor
DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor
Miscellaneous Control
00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor
Link Control
01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06)
02:00.0 Multimedia video controller: Conexant Systems, Inc. CX23885 PCI
Video and Audio Decoder (rev 02)
04:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host
Controller (rev ff)
05:00.0 SATA controller: JMicron Technology Corp. JMB361 AHCI/IDE (rev 02)
05:00.1 IDE interface: JMicron Technology Corp. JMB361 AHCI/IDE (rev 02)
06:00.0 VGA compatible controller: NVIDIA Corporation G98 [GeForce 8400
GS] (rev a1)
lsusb
Bus 001 Device 002: ID 0451:8042 Texas Instruments, Inc.
Bus 009 Device 002: ID 0bda:0301 Realtek Semiconductor Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 008 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 009 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 003: ID 046d:c050 Logitech, Inc. RX 250 Optical Mouse
--
Ulrich Eckhardt http://www.uli-eckhardt.de
Ein Blitzableiter auf dem Kirchturm ist das denkbar stärkste
Misstrauensvotum gegen den lieben Gott. (Karl Krauss)
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
