Hi Anand, I just have a very minor comment, nothing functional :) > -----Original Message----- > From: linux-omap-owner@xxxxxxxxxxxxxxx [mailto:linux-omap- > owner@xxxxxxxxxxxxxxx] On Behalf Of Anand Gadiyar > Sent: Sunday, March 21, 2010 6:32 AM > To: linux-usb@xxxxxxxxxxxxxxx; linux-omap@xxxxxxxxxxxxxxx > Cc: Gadiyar, Anand > Subject: [PATCH RFC 1/5] omap3: add platform init code for OHCI driver > > Add platform init code for the OMAP3 OHCI driver. > > Also, by default add mux-mode changes for all 6 pads for a > given port. This needs to be tailored down depending on the > actual port modes used. > > Signed-off-by: Anand Gadiyar <gadiyar@xxxxxx> > --- > arch/arm/mach-omap2/usb-ehci.c | 131 > ++++++++++++++++++++++++++++++++++ > arch/arm/plat-omap/include/plat/usb.h | 20 +++++ > 2 files changed, 151 insertions(+) > > Index: linux-2.6/arch/arm/mach-omap2/usb-ehci.c > =================================================================== > --- linux-2.6.orig/arch/arm/mach-omap2/usb-ehci.c > +++ linux-2.6/arch/arm/mach-omap2/usb-ehci.c > @@ -236,3 +236,134 @@ void __init usb_ehci_init(const struct e > > #endif /* CONFIG_USB_EHCI_HCD */ > > +#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) > + > +static struct resource ohci_resources[] = { > + { > + .start = OMAP34XX_OHCI_BASE, > + .end = OMAP34XX_OHCI_BASE + SZ_1K - 1, > + .flags = IORESOURCE_MEM, > + }, > + { > + .start = OMAP34XX_UHH_CONFIG_BASE, > + .end = OMAP34XX_UHH_CONFIG_BASE + SZ_1K - 1, > + .flags = IORESOURCE_MEM, > + }, > + { > + .start = OMAP34XX_USBTLL_BASE, > + .end = OMAP34XX_USBTLL_BASE + SZ_4K - 1, > + .flags = IORESOURCE_MEM, > + }, > + { /* general IRQ */ > + .start = INT_34XX_OHCI_IRQ, > + .flags = IORESOURCE_IRQ, > + } > +}; > + > +/* The dmamask must be set for OHCI to work */ > +static u64 ohci_dmamask = ~(u32)0; > + > +static void usb_release(struct device *dev) > +{ > + /* normally not freed */ > +} > + > +static struct platform_device ohci_device = { > + .name = "ohci-omap3", > + .id = 0, > + .dev = { > + .release = usb_release, > + .dma_mask = &ohci_dmamask, > + .coherent_dma_mask = 0xffffffff, > + .platform_data = NULL, > + }, > + .num_resources = ARRAY_SIZE(ohci_resources), > + .resource = ohci_resources, > +}; > + > +static void setup_ohci_io_mux(enum ohci_omap3_port_mode *port_mode) > +{ > + /* REVISIT: these need to be tailored for each of the modes */ > + switch (port_mode[0]) { > + case OMAP_OHCI_PORT_MODE_PHY_3PIN_DATSE0: > + case OMAP_OHCI_PORT_MODE_PHY_4PIN_DPDM: > + omap_mux_init_signal("mm1_rxdp", > + OMAP_PIN_INPUT_PULLDOWN); > + omap_mux_init_signal("mm1_rxdm", > + OMAP_PIN_INPUT_PULLDOWN); > + omap_mux_init_signal("mm1_txse0", > + OMAP_PIN_INPUT_PULLDOWN); > + omap_mux_init_signal("mm1_rxrcv", > + OMAP_PIN_INPUT_PULLDOWN); > + omap_mux_init_signal("mm1_txdat", > + OMAP_PIN_INPUT_PULLDOWN); > + omap_mux_init_signal("mm1_txen_n", OMAP_PIN_OUTPUT); > + break; > + case OMAP_OHCI_PORT_MODE_UNUSED: > + default: > + /* FALLTHROUGH */ Is this the right place for the fall through comment? I guess you meant Between 'case OMAP_OHCI_PORT_MODE_UNUSED:' and "default:" lines... Anyways, IMHO, as there's no code to execute in default case, maybe it's a bit unnecessary to state you'll falling through. > + break; > + } > + switch (port_mode[1]) { > + case OMAP_OHCI_PORT_MODE_PHY_3PIN_DATSE0: > + case OMAP_OHCI_PORT_MODE_PHY_4PIN_DPDM: > + omap_mux_init_signal("mm2_rxdp", > + OMAP_PIN_INPUT_PULLDOWN); > + omap_mux_init_signal("mm2_rxdm", > + OMAP_PIN_INPUT_PULLDOWN); > + omap_mux_init_signal("mm2_txse0", > + OMAP_PIN_INPUT_PULLDOWN); > + omap_mux_init_signal("mm2_rxrcv", > + OMAP_PIN_INPUT_PULLDOWN); > + omap_mux_init_signal("mm2_txdat", > + OMAP_PIN_INPUT_PULLDOWN); > + omap_mux_init_signal("mm2_txen_n", OMAP_PIN_OUTPUT); > + break; > + case OMAP_OHCI_PORT_MODE_UNUSED: > + default: > + /* FALLTHROUGH */ Same case here. > + break; > + } > + switch (port_mode[2]) { > + case OMAP_OHCI_PORT_MODE_PHY_3PIN_DATSE0: > + case OMAP_OHCI_PORT_MODE_PHY_4PIN_DPDM: > + omap_mux_init_signal("mm3_rxdp", > + OMAP_PIN_INPUT_PULLDOWN); > + omap_mux_init_signal("mm3_rxdm", > + OMAP_PIN_INPUT_PULLDOWN); > + omap_mux_init_signal("mm3_txse0", > + OMAP_PIN_INPUT_PULLDOWN); > + omap_mux_init_signal("mm3_rxrcv", > + OMAP_PIN_INPUT_PULLDOWN); > + omap_mux_init_signal("mm3_txdat", > + OMAP_PIN_INPUT_PULLDOWN); > + omap_mux_init_signal("mm3_txen_n", OMAP_PIN_OUTPUT); > + break; > + case OMAP_OHCI_PORT_MODE_UNUSED: > + default: > + /* FALLTHROUGH */ And here. Regards, Sergio > + break; > + } > +} > + > +void __init usb_ohci_init(const struct ohci_hcd_omap_platform_data > *pdata) > +{ > + platform_device_add_data(&ohci_device, pdata, sizeof(*pdata)); > + > + /* Setup Pin IO MUX for OHCI */ > + if (cpu_is_omap34xx()) > + setup_ohci_io_mux(pdata->port_mode); > + > + if (platform_device_register(&ohci_device) < 0) { > + pr_err("Unable to register FS-USB (OHCI) device\n"); > + return; > + } > +} > + > +#else > + > +void __init usb_ohci_init(const struct ohci_hcd_omap_platform_data > *pdata) > +{ > +} > + > +#endif /* CONFIG_USB_OHCI_HCD */ > Index: linux-2.6/arch/arm/plat-omap/include/plat/usb.h > =================================================================== > --- linux-2.6.orig/arch/arm/plat-omap/include/plat/usb.h > +++ linux-2.6/arch/arm/plat-omap/include/plat/usb.h > @@ -13,6 +13,20 @@ enum ehci_hcd_omap_mode { > EHCI_HCD_OMAP_MODE_TLL, > }; > > +enum ohci_omap3_port_mode { > + OMAP_OHCI_PORT_MODE_UNUSED, > + OMAP_OHCI_PORT_MODE_PHY_6PIN_DATSE0, > + OMAP_OHCI_PORT_MODE_PHY_6PIN_DPDM, > + OMAP_OHCI_PORT_MODE_PHY_3PIN_DATSE0, > + OMAP_OHCI_PORT_MODE_PHY_4PIN_DPDM, > + OMAP_OHCI_PORT_MODE_TLL_6PIN_DATSE0, > + OMAP_OHCI_PORT_MODE_TLL_6PIN_DPDM, > + OMAP_OHCI_PORT_MODE_TLL_3PIN_DATSE0, > + OMAP_OHCI_PORT_MODE_TLL_4PIN_DPDM, > + OMAP_OHCI_PORT_MODE_TLL_2PIN_DATSE0, > + OMAP_OHCI_PORT_MODE_TLL_2PIN_DPDM, > +}; > + > struct ehci_hcd_omap_platform_data { > enum ehci_hcd_omap_mode port_mode[OMAP3_HS_USB_PORTS]; > unsigned phy_reset:1; > @@ -21,6 +35,10 @@ struct ehci_hcd_omap_platform_data { > int reset_gpio_port[OMAP3_HS_USB_PORTS]; > }; > > +struct ohci_hcd_omap_platform_data { > + enum ohci_omap3_port_mode port_mode[OMAP3_HS_USB_PORTS]; > +}; > + > /*----------------------------------------------------------------------- > --*/ > > #define OMAP1_OTG_BASE 0xfffb0400 > @@ -55,6 +73,8 @@ extern void usb_musb_init(struct omap_mu > > extern void usb_ehci_init(const struct ehci_hcd_omap_platform_data > *pdata); > > +extern void usb_ohci_init(struct ohci_hcd_omap_platform_data *pdata); > + > #endif > > void omap_usb_init(struct omap_usb_config *pdata); > -- > To unsubscribe from this list: send the line "unsubscribe linux-omap" in > the body of a message to majordomo@xxxxxxxxxxxxxxx > More majordomo info at http://vger.kernel.org/majordomo-info.html -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
