On Sun, Mar 21, 2010 at 05:01:59PM +0530, Anand Gadiyar wrote:
> Add platform init code for the OMAP3 OHCI driver.
>
> Also, by default add mux-mode changes for all 6 pads for a
> given port. This needs to be tailored down depending on the
> actual port modes used.
>
> Signed-off-by: Anand Gadiyar <gadiyar@xxxxxx>
> ---
> arch/arm/mach-omap2/usb-ehci.c | 131 ++++++++++++++++++++++++++++++++++
> arch/arm/plat-omap/include/plat/usb.h | 20 +++++
> 2 files changed, 151 insertions(+)
>
> Index: linux-2.6/arch/arm/mach-omap2/usb-ehci.c
> ===================================================================
> --- linux-2.6.orig/arch/arm/mach-omap2/usb-ehci.c
> +++ linux-2.6/arch/arm/mach-omap2/usb-ehci.c
> @@ -236,3 +236,134 @@ void __init usb_ehci_init(const struct e
>
> #endif /* CONFIG_USB_EHCI_HCD */
>
> +#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
> +
> +static struct resource ohci_resources[] = {
> + {
> + .start = OMAP34XX_OHCI_BASE,
> + .end = OMAP34XX_OHCI_BASE + SZ_1K - 1,
> + .flags = IORESOURCE_MEM,
> + },
> + {
> + .start = OMAP34XX_UHH_CONFIG_BASE,
> + .end = OMAP34XX_UHH_CONFIG_BASE + SZ_1K - 1,
> + .flags = IORESOURCE_MEM,
> + },
> + {
> + .start = OMAP34XX_USBTLL_BASE,
> + .end = OMAP34XX_USBTLL_BASE + SZ_4K - 1,
> + .flags = IORESOURCE_MEM,
> + },
> + { /* general IRQ */
> + .start = INT_34XX_OHCI_IRQ,
> + .flags = IORESOURCE_IRQ,
> + }
> +};
> +
> +/* The dmamask must be set for OHCI to work */
> +static u64 ohci_dmamask = ~(u32)0;
DMA_BIT_MASK(32); ??
> +static void usb_release(struct device *dev)
> +{
> + /* normally not freed */
> +}
unnecessary ?
> +static struct platform_device ohci_device = {
> + .name = "ohci-omap3",
> + .id = 0,
> + .dev = {
> + .release = usb_release,
> + .dma_mask = &ohci_dmamask,
> + .coherent_dma_mask = 0xffffffff,
> + .platform_data = NULL,
static variable, doesn't need the NULL initialization.
[snip]
> +#endif /* CONFIG_USB_OHCI_HCD */
> Index: linux-2.6/arch/arm/plat-omap/include/plat/usb.h
> ===================================================================
> --- linux-2.6.orig/arch/arm/plat-omap/include/plat/usb.h
> +++ linux-2.6/arch/arm/plat-omap/include/plat/usb.h
> @@ -13,6 +13,20 @@ enum ehci_hcd_omap_mode {
> EHCI_HCD_OMAP_MODE_TLL,
> };
>
> +enum ohci_omap3_port_mode {
> + OMAP_OHCI_PORT_MODE_UNUSED,
> + OMAP_OHCI_PORT_MODE_PHY_6PIN_DATSE0,
> + OMAP_OHCI_PORT_MODE_PHY_6PIN_DPDM,
> + OMAP_OHCI_PORT_MODE_PHY_3PIN_DATSE0,
> + OMAP_OHCI_PORT_MODE_PHY_4PIN_DPDM,
> + OMAP_OHCI_PORT_MODE_TLL_6PIN_DATSE0,
> + OMAP_OHCI_PORT_MODE_TLL_6PIN_DPDM,
> + OMAP_OHCI_PORT_MODE_TLL_3PIN_DATSE0,
> + OMAP_OHCI_PORT_MODE_TLL_4PIN_DPDM,
> + OMAP_OHCI_PORT_MODE_TLL_2PIN_DATSE0,
> + OMAP_OHCI_PORT_MODE_TLL_2PIN_DPDM,
> +};
> +
> struct ehci_hcd_omap_platform_data {
> enum ehci_hcd_omap_mode port_mode[OMAP3_HS_USB_PORTS];
> unsigned phy_reset:1;
> @@ -21,6 +35,10 @@ struct ehci_hcd_omap_platform_data {
> int reset_gpio_port[OMAP3_HS_USB_PORTS];
> };
>
> +struct ohci_hcd_omap_platform_data {
> + enum ohci_omap3_port_mode port_mode[OMAP3_HS_USB_PORTS];
> +};
> +
> /*-------------------------------------------------------------------------*/
>
> #define OMAP1_OTG_BASE 0xfffb0400
> @@ -55,6 +73,8 @@ extern void usb_musb_init(struct omap_mu
>
> extern void usb_ehci_init(const struct ehci_hcd_omap_platform_data *pdata);
>
> +extern void usb_ohci_init(struct ohci_hcd_omap_platform_data *pdata);
missing const ??
--
balbi
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
