Hi, On Monday 30 December 2013 03:13 PM, Vivek Gautam wrote: > Hi Kishon, > > > On Tue, Dec 24, 2013 at 11:15 PM, Kishon Vijay Abraham I <kishon@xxxxxx> wrote: >> Hi, >> >> >> On Thursday 05 December 2013 01:44 PM, Vivek Gautam wrote: >>> >>> Hi Kishon, >>> >>> >>> On Wed, Dec 4, 2013 at 7:58 PM, Kishon Vijay Abraham I <kishon@xxxxxx> >>> wrote: >>>> >>>> Hi Vivek, >>>> >>>> On Wednesday 20 November 2013 09:14 PM, Kishon Vijay Abraham I wrote: >>>>> >>>>> Hi, >>>>> >>>>> On Wednesday 20 November 2013 03:02 PM, Vivek Gautam wrote: >>>>>> >>>>>> On Wed, Nov 20, 2013 at 2:34 PM, Kishon Vijay Abraham I <kishon@xxxxxx> >>>>>> wrote: >>>>>>> >>>>>>> On Wednesday 20 November 2013 02:27 PM, Vivek Gautam wrote: >>>>>>>> >>>>>>>> Hi Kishon, >>>>>>>> >>>>>>>> >>>>>>>> On Mon, Nov 11, 2013 at 4:41 PM, Kishon Vijay Abraham I >>>>>>>> <kishon@xxxxxx> wrote: >>>>>>>>> >>>>>>>>> Hi, >>>>>>>> >>>>>>>> sorry for the delayed response. >>>>>>>> >>>>>>>>> >>>>>>>>> On Wednesday 06 November 2013 05:37 AM, Jingoo Han wrote: >>>>>>>>>> >>>>>>>>>> On Wednesday, November 06, 2013 2:58 AM, Vivek Gautam wrote: >>>>>>>>>>> >>>>>>>>>>> On Tue, Nov 5, 2013 at 5:33 PM, Jingoo Han <jg1.han@xxxxxxxxxxx> >>>>>>>>>>> wrote: >>>>>>>>>> >>>>>>>>>> >>>>>>>>>> [.....] >>>>>>>>>> >>>>>>>>>>>> USB3.0 PHY consists of two blocks such as 3.0 block and 2.0 >>>>>>>>>>>> block. >>>>>>>>>>>> This USB3.0 PHY can support UTMI+ and PIPE3 interface for 3.0 >>>>>>>>>>>> block >>>>>>>>>>>> and 2.0 block, respectively. >>>>>>>>>>>> >>>>>>>>>>>> Conclusion: >>>>>>>>>>>> >>>>>>>>>>>> 1) USB2.0 PHY: USB2.0 HOST, USB2.0 Device >>>>>>>>>>>> Base address: 0x1213 0000 >>>>>>>>>>>> >>>>>>>>>>>> 2) USB3.0 PHY: USB3.0 DRD (3.0 HOST & 3.0 Device) >>>>>>>>>>>> Base address: 0x1210 0000 >>>>>>>>>>>> 2.0 block(UTMI+) & 3.0 block(PIPE3) >>>>>>>>>>> >>>>>>>>>>> >>>>>>>>>>> And this is of course the PHY used by DWC3 controller, which works >>>>>>>>>>> at >>>>>>>>>>> both High speed as well as Super Speed. >>>>>>>>>>> Right ? >>>>>>>>>> >>>>>>>>>> >>>>>>>>>> Right. >>>>>>>>>> >>>>>>>>>> While 3.0 block(PIPE3) can be used for Super Speed, 2.0 >>>>>>>>>> block(UTMI+) >>>>>>>>>> can be used for High speed. >>>>>>>>> >>>>>>>>> >>>>>>>>> It should then come under *single IP muliple PHY* category similar >>>>>>>>> to what >>>>>>>>> Sylwester has done. >>>>>>>> >>>>>>>> >>>>>>>> Do you mean that i should be including PHY IDs for UTMI+ phy and >>>>>>>> PIPE3 >>>>>>>> phy present in this PHY block ? >>>>>>>> AFAICS the two phys (UTMI+ and PIPE3) do not really have separate >>>>>>>> registers to program, and that's the reason >>>>>>>> we program the entire PHY in a shot. >>>>>>> >>>>>>> >>>>>>> you mean you program the same set of bits for UTMI+ and PIPE3? >>>>>> >>>>>> >>>>>> No, looking closely into PHY datasheet as well as Exynos5250 manual, i >>>>>> can see that UTMI+ and PIPE3 >>>>>> phys have separate bit settings. So i think we should be able to >>>>>> segregate the two PHYs (UTMI+ and PIPE3). >>>>>> Pardon me for my earlier observations. >>>>> >>>>> >>>>> no problem.. >>>>>> >>>>>> Let me clarify more with our h/w team also on this and then i will >>>>>> confirm with this. >>>> >>>> >>>> Did you get more information on this? >>> >>> >>> Yes, i have been in contact with our hardware team. >>> The functionality of setting up UTMI+ and PIPE3 phys separately, and >>> thereby using only one functionality of the two >>> at some point of time (either high speed or super speed) hasn't been >>> tested so far. >> >> >> Irrespective of whether we are able to test the functionality separately or >> not, we should model it as multiple PHYs since you have separate bit >> settings for UTMI+ and PIPE3. >> >> (I'll review your next patch version shortly). > > Thanks Kishon, i know i am disturbing you in the holiday season. :-) > But there's one concern, on Exynos5 platforms we have only one bit to > power control > the entire PHY (irrespective of the two PHYs present in the USB 3.0 > PHY controller). > So anyways we won't be able to save anything on the power front even > if we program only > one PHY (UTMI/PIPE3). > Although there are PHY settings register bits which seem separate for > the two phys. r > What do you suggest in that case ? The idea is to model the driver as close to the hardware though I understand there won't be any advantages w.r.t power or performance. maybe in later versions of the IP we'll have separate bits to control usb3 and usb2. I think for power control we should have both usb3 and usb2 power-on callback calling a single function that controls the power bit. Thanks Kishon -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
