Cheers
Kishon
Signed-off-by: Vivek Gautam <gautam.vivek@xxxxxxxxxxx>
---
.../devicetree/bindings/phy/samsung-phy.txt | 20 +
drivers/phy/Kconfig | 7 +
drivers/phy/Makefile | 1 +
drivers/phy/phy-exynos5-usb3.c | 562
++++++++++++++++++++
4 files changed, 590 insertions(+), 0 deletions(-)
create mode 100644 drivers/phy/phy-exynos5-usb3.c
diff --git a/Documentation/devicetree/bindings/phy/samsung-phy.txt
b/Documentation/devicetree/bindings/phy/samsung-phy.txt
index c0fccaa..9b5c111 100644
--- a/Documentation/devicetree/bindings/phy/samsung-phy.txt
+++ b/Documentation/devicetree/bindings/phy/samsung-phy.txt
@@ -20,3 +20,23 @@ Required properties:
- compatible : should be "samsung,exynos5250-dp-video-phy";
- reg : offset and length of the Display Port PHY register set;
- #phy-cells : from the generic PHY bindings, must be 0;
+
+Samsung Exynos5 SoC seiries USB 3.0 PHY controller
+--------------------------------------------------
+
+Required properties:
+- compatible :
+ should be "samsung,exynos5250-usb3phy" for exynos5250 SoC
+ should be "samsung,exynos5420-usb3phy" for exynos5420 SoC
+- reg : Register offset and length array
+ - first field corresponds to USB 3.0 PHY register set;
+ - second field corresponds to PHY power isolation register
+ present in PMU;
+- clocks: Clock IDs array as required by the controller
+- clock-names: names of clocks correseponding to IDs in the clock
property;
+ Required clocks:
+ - first clock is main PHY clock (same as USB 3.0 controller IP
clock)
+ - second clock is reference clock (usually crystal clock)
+ optional clock:
+ - third clock is special clock used by PHY for operation
+- #phy-cells : from the generic PHY bindings, must be 0;
diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig index
a344f3d..9a100c6 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -51,4 +51,11 @@ config PHY_EXYNOS_DP_VIDEO
help
Support for Display Port PHY found on Samsung EXYNOS SoCs.
+config PHY_EXYNOS5_USB3
+ tristate "Exynos5 SoC series USB 3.0 PHY driver"
+ depends on ARCH_EXYNOS5
+ select GENERIC_PHY
+ help
+ Enable USB 3.0 PHY support for Exynos 5 SoC series
+
endmenu
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile index
d0caae9..9c06a61 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -7,3 +7,4 @@ obj-$(CONFIG_PHY_EXYNOS_DP_VIDEO) += phy-exynos-dp-
video.o
obj-$(CONFIG_PHY_EXYNOS_MIPI_VIDEO) += phy-exynos-mipi-video.o
obj-$(CONFIG_OMAP_USB2) += phy-omap-usb2.o
obj-$(CONFIG_TWL4030_USB) += phy-twl4030-usb.o
+obj-$(CONFIG_PHY_EXYNOS5_USB3) += phy-exynos5-usb3.o
diff --git a/drivers/phy/phy-exynos5-usb3.c
b/drivers/phy/phy-exynos5-usb3.c new file mode 100644 index
0000000..b9a2674
--- /dev/null
+++ b/drivers/phy/phy-exynos5-usb3.c
@@ -0,0 +1,562 @@
+/*
+ * Samsung EXYNOS5 SoC series USB 3.0 PHY driver
+ *
+ * Copyright (C) 2013 Samsung Electronics Co., Ltd.
+ * Author: Vivek Gautam <gautam.vivek@xxxxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or
+modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/mutex.h>
+
+/* Exynos USB PHY registers */
+#define EXYNOS5_FSEL_9MHZ6 0x0
+#define EXYNOS5_FSEL_10MHZ 0x1
+#define EXYNOS5_FSEL_12MHZ 0x2
+#define EXYNOS5_FSEL_19MHZ2 0x3
+#define EXYNOS5_FSEL_20MHZ 0x4
+#define EXYNOS5_FSEL_24MHZ 0x5
+#define EXYNOS5_FSEL_50MHZ 0x7
+
+/* EXYNOS5: USB 3.0 DRD PHY registers */
+#define EXYNOS5_DRD_LINKSYSTEM (0x04)
+
+#define LINKSYSTEM_FLADJ_MASK (0x3f << 1)
+#define LINKSYSTEM_FLADJ(_x) ((_x) << 1)
+#define LINKSYSTEM_XHCI_VERSION_CONTROL (0x1 << 27)
+
+#define EXYNOS5_DRD_PHYUTMI (0x08)
+
+#define PHYUTMI_OTGDISABLE (0x1 << 6)
+#define PHYUTMI_FORCESUSPEND (0x1 << 1)
+#define PHYUTMI_FORCESLEEP (0x1 << 0)
+
+#define EXYNOS5_DRD_PHYPIPE (0x0c)
+
+#define EXYNOS5_DRD_PHYCLKRST (0x10)
+
+#define PHYCLKRST_SSC_REFCLKSEL_MASK (0xff << 23)
+#define PHYCLKRST_SSC_REFCLKSEL(_x) ((_x) << 23)
+
+#define PHYCLKRST_SSC_RANGE_MASK (0x03 << 21)
+#define PHYCLKRST_SSC_RANGE(_x) ((_x) << 21)
+
+#define PHYCLKRST_SSC_EN (0x1 << 20)
+#define PHYCLKRST_REF_SSP_EN (0x1 << 19)
+#define PHYCLKRST_REF_CLKDIV2 (0x1 << 18)
+
+#define PHYCLKRST_MPLL_MULTIPLIER_MASK (0x7f << 11)
+#define PHYCLKRST_MPLL_MULTIPLIER_100MHZ_REF (0x19 << 11)
+#define PHYCLKRST_MPLL_MULTIPLIER_50M_REF (0x02 << 11)
+#define PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF (0x68 << 11)
+#define PHYCLKRST_MPLL_MULTIPLIER_20MHZ_REF (0x7d << 11)
+#define PHYCLKRST_MPLL_MULTIPLIER_19200KHZ_REF (0x02 << 11)
+
+#define PHYCLKRST_FSEL_MASK (0x3f << 5)
+#define PHYCLKRST_FSEL(_x) ((_x) << 5)
+#define PHYCLKRST_FSEL_PAD_100MHZ (0x27 << 5)
+#define PHYCLKRST_FSEL_PAD_24MHZ (0x2a << 5)
+#define PHYCLKRST_FSEL_PAD_20MHZ (0x31 << 5)
+#define PHYCLKRST_FSEL_PAD_19_2MHZ (0x38 << 5)
+
+#define PHYCLKRST_RETENABLEN (0x1 << 4)
+
+#define PHYCLKRST_REFCLKSEL_MASK (0x03 << 2)
+#define PHYCLKRST_REFCLKSEL_PAD_REFCLK (0x2 << 2)
+#define PHYCLKRST_REFCLKSEL_EXT_REFCLK (0x3 << 2)
+
+#define PHYCLKRST_PORTRESET (0x1 << 1)
+#define PHYCLKRST_COMMONONN (0x1 << 0)
+
+#define EXYNOS5_DRD_PHYREG0 (0x14)
+#define EXYNOS5_DRD_PHYREG1 (0x18)
+
+#define EXYNOS5_DRD_PHYPARAM0 (0x1c)
+
+#define PHYPARAM0_REF_USE_PAD (0x1 << 31)
+#define PHYPARAM0_REF_LOSLEVEL_MASK (0x1f << 26)
+#define PHYPARAM0_REF_LOSLEVEL (0x9 << 26)
+
+#define EXYNOS5_DRD_PHYPARAM1 (0x20)
+
+#define PHYPARAM1_PCS_TXDEEMPH_MASK (0x1f << 0)
+#define PHYPARAM1_PCS_TXDEEMPH (0x1c)
+
+#define EXYNOS5_DRD_PHYTERM (0x24)
+
+#define EXYNOS5_DRD_PHYTEST (0x28)
+
+#define PHYTEST_POWERDOWN_SSP (0x1 << 3)
+#define PHYTEST_POWERDOWN_HSP (0x1 << 2)
+
+#define EXYNOS5_DRD_PHYADP (0x2c)
+
+#define EXYNOS5_DRD_PHYBATCHG (0x30)
+
+#define PHYBATCHG_UTMI_CLKSEL (0x1 << 2)
+
+#define EXYNOS5_DRD_PHYRESUME (0x34)
+#define EXYNOS5_DRD_LINKPORT (0x44)
+
+
+/* Isolation, configured in the power management unit */
+#define EXYNOS5_USB_ISOL_DRD (1 << 0)
+
+#define CLKSEL_ERROR -1
+
+#ifndef KHZ
+#define KHZ 1000
+#endif
+
+#ifndef MHZ
+#define MHZ (KHZ * KHZ)
+#endif
+
+enum samsung_cpu_type {
+ TYPE_EXYNOS5250,
+ TYPE_EXYNOS5420,
+};
+
+enum usb3phy_state {
+ STATE_OFF,
+ STATE_ON,
+};
+
+struct usb3phy_config {
+ enum samsung_cpu_type cpu;
+ bool has_sclk_usbphy30;
+};
+
+struct usb3phy_instance {
+ char *label;
+ struct usb3phy_driver *drv;
+ struct phy *phy;
+ enum usb3phy_state state;
+ u32 clk;
+ unsigned long rate;
+};
+
+struct usb3phy_driver {
+ struct device *dev;
+ void __iomem *reg_phy;
+ void __iomem *reg_isol;
+ struct clk *clk;
+ struct clk *sclk_usbphy30;
+ struct usb3phy_instance instance;
+};
+
+/*
+ * exynos5_rate_to_clk() converts the supplied clock rate to the
+value that
+ * can be written to the phy register.
+ */
+static u32 exynos5_rate_to_clk(unsigned long rate) {
+ unsigned int clksel;
+
+ /* EXYNOS5_FSEL_MASK */
+
+ switch (rate) {
+ case 9600 * KHZ:
+ clksel = EXYNOS5_FSEL_9MHZ6;
+ break;
+ case 10 * MHZ:
+ clksel = EXYNOS5_FSEL_10MHZ;
+ break;
+ case 12 * MHZ:
+ clksel = EXYNOS5_FSEL_12MHZ;
+ break;
+ case 19200 * KHZ:
+ clksel = EXYNOS5_FSEL_19MHZ2;
+ break;
+ case 20 * MHZ:
+ clksel = EXYNOS5_FSEL_20MHZ;
+ break;
+ case 24 * MHZ:
+ clksel = EXYNOS5_FSEL_24MHZ;
+ break;
+ case 50 * MHZ:
+ clksel = EXYNOS5_FSEL_50MHZ;
+ break;
+ default:
+ clksel = CLKSEL_ERROR;
+ }
+
+ return clksel;
+}
+
+static void exynos5_usb3phy_isol(struct usb3phy_instance *inst, bool
+on) {
+ struct usb3phy_driver *drv = inst->drv;
+ u32 tmp;
+
+ if (!drv->reg_isol)
+ return;
+
+ tmp = readl(drv->reg_isol);
+ if (on)
+ tmp &= ~EXYNOS5_USB_ISOL_DRD;
+ else
+ tmp |= EXYNOS5_USB_ISOL_DRD;
+ writel(tmp, drv->reg_isol);
+}
+
+/*
+ * Sets the phy clk as EXTREFCLK (XXTI) which is internal clock from
clock core.
+ */
+static u32 exynos5_usb3phy_set_refclk(struct usb3phy_instance *inst)
+{
+ u32 reg;
+ u32 refclk;
+
+ refclk = inst->clk;
+
+ reg = PHYCLKRST_REFCLKSEL_EXT_REFCLK |
+ PHYCLKRST_FSEL(refclk);
+
+ switch (refclk) {
+ case EXYNOS5_FSEL_50MHZ:
+ reg |= (PHYCLKRST_MPLL_MULTIPLIER_50M_REF |
+ PHYCLKRST_SSC_REFCLKSEL(0x00));
+ break;
+ case EXYNOS5_FSEL_20MHZ:
+ reg |= (PHYCLKRST_MPLL_MULTIPLIER_20MHZ_REF |
+ PHYCLKRST_SSC_REFCLKSEL(0x00));
+ break;
+ case EXYNOS5_FSEL_19MHZ2:
+ reg |= (PHYCLKRST_MPLL_MULTIPLIER_19200KHZ_REF |
+ PHYCLKRST_SSC_REFCLKSEL(0x88));
+ break;
+ case EXYNOS5_FSEL_24MHZ:
+ default:
+ reg |= (PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF |
+ PHYCLKRST_SSC_REFCLKSEL(0x88));
+ break;
+ }
+
+ return reg;
+}
+
+static void exynos5_usb3phy_init(struct usb3phy_instance *inst) {
+ struct usb3phy_driver *drv = inst->drv;
+ u32 phyparam0;
+ u32 phyparam1;
+ u32 linksystem;
+ u32 phybatchg;
+ u32 phytest;
+ u32 phyclkrst;
+
+ /* Reset USB 3.0 PHY */
+ writel(0x0, drv->reg_phy + EXYNOS5_DRD_PHYREG0);
+
+ phyparam0 = readl(drv->reg_phy + EXYNOS5_DRD_PHYPARAM0);
+ /* Select PHY CLK source */
+ phyparam0 &= ~PHYPARAM0_REF_USE_PAD;
+ /* Set Loss-of-Signal Detector sensitivity */
+ phyparam0 &= ~PHYPARAM0_REF_LOSLEVEL_MASK;
+ phyparam0 |= PHYPARAM0_REF_LOSLEVEL;
+ writel(phyparam0, drv->reg_phy + EXYNOS5_DRD_PHYPARAM0);
+
+ writel(0x0, drv->reg_phy + EXYNOS5_DRD_PHYRESUME);
+
+ /*
+ * Setting the Frame length Adj value[6:1] to default 0x20
+ * See xHCI 1.0 spec, 5.2.4
+ */
+ linksystem = LINKSYSTEM_XHCI_VERSION_CONTROL |
+ LINKSYSTEM_FLADJ(0x20);
+ writel(linksystem, drv->reg_phy + EXYNOS5_DRD_LINKSYSTEM);
+
+ phyparam1 = readl(drv->reg_phy + EXYNOS5_DRD_PHYPARAM1);
+ /* Set Tx De-Emphasis level */
+ phyparam1 &= ~PHYPARAM1_PCS_TXDEEMPH_MASK;
+ phyparam1 |= PHYPARAM1_PCS_TXDEEMPH;
+ writel(phyparam1, drv->reg_phy + EXYNOS5_DRD_PHYPARAM1);
+
+ phybatchg = readl(drv->reg_phy + EXYNOS5_DRD_PHYBATCHG);
+ phybatchg |= PHYBATCHG_UTMI_CLKSEL;
+ writel(phybatchg, drv->reg_phy + EXYNOS5_DRD_PHYBATCHG);
+
+ /* PHYTEST POWERDOWN Control */
+ phytest = readl(drv->reg_phy + EXYNOS5_DRD_PHYTEST);
+ phytest &= ~(PHYTEST_POWERDOWN_SSP |
+ PHYTEST_POWERDOWN_HSP);
+ writel(phytest, drv->reg_phy + EXYNOS5_DRD_PHYTEST);
+
+ /* UTMI Power Control */
+ writel(PHYUTMI_OTGDISABLE, drv->reg_phy + EXYNOS5_DRD_PHYUTMI);
+
+ phyclkrst = exynos5_usb3phy_set_refclk(inst);
+
+ phyclkrst |= PHYCLKRST_PORTRESET |
+ /* Digital power supply in normal operating mode */
+ PHYCLKRST_RETENABLEN |
+ /* Enable ref clock for SS function */
+ PHYCLKRST_REF_SSP_EN |
+ /* Enable spread spectrum */
+ PHYCLKRST_SSC_EN |
+ /* Power down HS Bias and PLL blocks in suspend mode
*/
+ PHYCLKRST_COMMONONN;
+
+ writel(phyclkrst, drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
+
+ udelay(10);
+
+ phyclkrst &= ~PHYCLKRST_PORTRESET;
+ writel(phyclkrst, drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
+
+}
+
+static void exynos5_usb3phy_exit(struct usb3phy_instance *inst) {
+ struct usb3phy_driver *drv = inst->drv;
+ u32 phyutmi;
+ u32 phyclkrst;
+ u32 phytest;
+
+ phyutmi = PHYUTMI_OTGDISABLE |
+ PHYUTMI_FORCESUSPEND |
+ PHYUTMI_FORCESLEEP;
+ writel(phyutmi, drv->reg_phy + EXYNOS5_DRD_PHYUTMI);
+
+ /* Resetting the PHYCLKRST enable bits to reduce leakage current
*/
+ phyclkrst = readl(drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
+ phyclkrst &= ~(PHYCLKRST_REF_SSP_EN |
+ PHYCLKRST_SSC_EN |
+ PHYCLKRST_COMMONONN);
+ writel(phyclkrst, drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
+
+ /* Control PHYTEST to remove leakage current */
+ phytest = readl(drv->reg_phy + EXYNOS5_DRD_PHYTEST);
+ phytest |= PHYTEST_POWERDOWN_SSP |
+ PHYTEST_POWERDOWN_HSP;
+ writel(phytest, drv->reg_phy + EXYNOS5_DRD_PHYTEST); }
+
+static int exynos5_usb3phy_power_on(struct phy *phy) {
+ struct usb3phy_instance *inst = phy_get_drvdata(phy);
+ struct usb3phy_driver *drv = inst->drv;
+ int ret;
+
+ dev_info(drv->dev, "Request to power_on \"%s\" usb phy\n",
+ inst->label);
+
+ if (drv->sclk_usbphy30)
+ clk_prepare_enable(drv->sclk_usbphy30);
+
+ ret = clk_prepare_enable(drv->clk);
+ if (ret)
+ return ret;
+
+ if (inst->state == STATE_ON) {
+ dev_err(drv->dev, "usb phy \"%s\" already on",
+ inst->label);
+ ret = -ENODEV;
+ goto err0;
+ }
+
+ inst->state = STATE_ON;
+
+ /* Initialize the PHY and power it ON */
+ exynos5_usb3phy_init(inst);
+ exynos5_usb3phy_isol(inst, 0);
+
+err0:
+ clk_disable_unprepare(drv->clk);
+
+ return ret;
+}
+
+static int exynos5_usb3phy_power_off(struct phy *phy) {
+ struct usb3phy_instance *inst = phy_get_drvdata(phy);
+ struct usb3phy_driver *drv = inst->drv;
+ int ret;
+
+ dev_info(drv->dev, "Request to power_off \"%s\" usb phy\n",
+ inst->label);
+ ret = clk_prepare_enable(drv->clk);
+ if (ret)
+ return ret;
+
+ if (inst->state == STATE_OFF) {
+ dev_err(drv->dev, "usb phy \"%s\" already off",
+ inst->label);
+ ret = -ENODEV;
+ goto err0;
+ }
+
+ inst->state = STATE_OFF;
+
+ /* Power-off the PHY and de-initialize it */
+ exynos5_usb3phy_isol(inst, 1);
+ exynos5_usb3phy_exit(inst);
+
+err0:
+ clk_disable_unprepare(drv->clk);
+ if (drv->sclk_usbphy30)
+ clk_disable_unprepare(drv->sclk_usbphy30);
+
+ return ret;
+}
+
+static struct phy_ops exynos5_usb3phy_ops = {
+ .power_on = exynos5_usb3phy_power_on,
+ .power_off = exynos5_usb3phy_power_off,
+ .owner = THIS_MODULE,
+};
+
+static const struct of_device_id exynos5_usb3phy_of_match[];
+
+static int exynos5_usb3phy_probe(struct platform_device *pdev) {
+ struct device *dev = &pdev->dev;
+ struct usb3phy_driver *drv;
+ struct usb3phy_instance *inst;
+ struct phy_provider *phy_provider;
+ struct resource *res;
+ struct clk *clk;
+ const struct of_device_id *match;
+ const struct usb3phy_config *cfg;
+
+ match = of_match_node(exynos5_usb3phy_of_match, pdev-
dev.of_node);
+ if (!match) {
+ dev_err(dev, "of_match_node() failed\n");
+ return -EINVAL;
+ }
+ cfg = match->data;
+ if (!cfg) {
+ dev_err(dev, "Failed to get configuration\n");
+ return -EINVAL;
+ }
+
+ drv = devm_kzalloc(dev, sizeof(struct usb3phy_driver),
GFP_KERNEL);
+ if (!drv) {
+ dev_err(dev, "Failed to allocate memory\n");
+ return -ENOMEM;
+ }
+
+ dev_set_drvdata(dev, drv);
+ drv->dev = dev;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ drv->reg_phy = devm_ioremap_resource(dev, res);
+ if (IS_ERR(drv->reg_phy)) {
+ dev_err(dev, "Failed to map register memory (phy)\n");
+ return PTR_ERR(drv->reg_phy);
+ }
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+ drv->reg_isol = devm_ioremap_resource(dev, res);
+ if (IS_ERR(drv->reg_isol)) {
+ dev_err(dev, "Failed to map register memory (isolation)\n");
+ return PTR_ERR(drv->reg_isol);
+ }
+
+ phy_provider = devm_of_phy_provider_register(dev,
of_phy_simple_xlate);
+ if (IS_ERR(phy_provider)) {
+ dev_err(drv->dev, "Failed to register phy provider\n");
+ return PTR_ERR(phy_provider);
+ }
+
+ drv->clk = devm_clk_get(dev, "phy");
+ if (IS_ERR(drv->clk)) {
+ dev_err(dev, "Failed to get clock of phy controller\n");
+ return PTR_ERR(drv->clk);
+ }
+
+ /*
+ * Exysno5420 SoC has an additional special clock, used for
+ * for USB 3.0 PHY operation, this clock goes to the PHY block
+ * as a reference clock to clock generation block of the
controller.
+ */
+ if (cfg->has_sclk_usbphy30) {
+ drv->sclk_usbphy30 = devm_clk_get(dev, "sclk_usbphy30");
+ if (IS_ERR(drv->clk)) {
+ dev_err(dev, "Failed to get phy reference clock\n");
+ return PTR_ERR(drv->clk);
+ }
+ }
+
+ inst = &drv->instance;
+ inst->drv = drv;
+ inst->label = "usb3drd";
+
+ dev_info(dev, "Creating phy \"%s\"\n", inst->label);
+ inst->phy = devm_phy_create(dev, &exynos5_usb3phy_ops, NULL);
+ if (IS_ERR(inst->phy)) {
+ dev_err(drv->dev, "Failed to create usb3phy \"%s\"\n",
+ inst->label);
+ return PTR_ERR(inst->phy);
+ }
+
+ phy_set_drvdata(inst->phy, inst);
+
+ clk = clk_get(dev, inst->label);
+ if (IS_ERR(clk)) {
+ dev_err(dev, "Failed to get clock of \"%s\" phy\n",
+ inst->label);
+ return PTR_ERR(clk);
+ }
+
+ inst->rate = clk_get_rate(clk);
+
+ inst->clk = exynos5_rate_to_clk(inst->rate);
+ if (inst->clk == CLKSEL_ERROR) {
+ dev_err(dev, "Clock rate (%ld) not supported\n",
+ inst->rate);
+ clk_put(clk);
+ return -EINVAL;
+ }
+ clk_put(clk);
+
+ return 0;
+}
+
+const struct usb3phy_config exynos5420_usb3phy_cfg = {
+ .cpu = TYPE_EXYNOS5420,
+ .has_sclk_usbphy30 = true,
+};
+
+const struct usb3phy_config exynos5250_usb3phy_cfg = {
+ .cpu = TYPE_EXYNOS5250,
+ .has_sclk_usbphy30 = false,
+};
+
+static const struct of_device_id exynos5_usb3phy_of_match[] = {
+ {
+ .compatible = "samsung,exynos5250-usb3phy",
+ .data = &exynos5250_usb3phy_cfg
+ }, {
+ .compatible = "samsung,exynos5420-usb3phy",
+ .data = &exynos5420_usb3phy_cfg
+ },
+ { },
+};
+
+static struct platform_driver exynos5_usb3phy_driver = {
+ .probe = exynos5_usb3phy_probe,
+ .driver = {
+ .of_match_table = exynos5_usb3phy_of_match,
+ .name = "exynos5-usb3phy",
+ .owner = THIS_MODULE,
+ }
+};
+
+module_platform_driver(exynos5_usb3phy_driver);
+MODULE_DESCRIPTION("Samsung EXYNOS5 series SoC USB 3.0 PHY driver");
+MODULE_AUTHOR("Vivek Gautam <gautam.vivek@xxxxxxxxxxx>");
+MODULE_LICENSE("GPL v2"); MODULE_ALIAS("platform:exynos5-usb3phy");
