Hi Kishon, On Mon, Nov 4, 2013 at 6:42 PM, Kishon Vijay Abraham I <kishon@xxxxxx> wrote: > Hi, > > > On Monday 04 November 2013 03:45 PM, Kamil Debski wrote: >> >> Hi Kishon, >> >>> From: Kishon Vijay Abraham I [mailto:kishon@xxxxxx] >>> Sent: Monday, November 04, 2013 7:55 AM >>> >>> Hi Vivek, >>> >>> On Thursday 31 October 2013 01:15 PM, Vivek Gautam wrote: >>>> >>>> Add a new driver for the USB 3.0 PHY on Exynos5 series of SoCs. >>>> The new driver uses the generic PHY framework and will interact with >>>> DWC3 controller present on Exynos5 series of SoCs. >>> >>> >>> In Exynos, you have a single IP that supports both USB3 and USB2 PHY >>> right? I think that needs to be mentioned here. >> >> >> As far as I know the IP is different. > > > Ok. Sometime back Vivek was mentioning about a single IP for both USB3 and > USB2. Thought it should be this driver. Anyway thanks for the clarification. Right Kishon, I had mentioned that Exynos5's dwc3 controller have a single IP for USB2 and USB3 phy. >From what i see, on exynos5 systems the dwc3 controller uses a combo of usb 2 (utmi+) and usb 3 (pipe 3) phy (with base address starting 0x12100000). Kamil, Tomasz, Please correct me if i am wrong. > > Cheers > Kishon > >> >>> Do you have separate registers that should be used for >>> initializing/powerin_on/powering_off etc.. for usb2 phy and usb3 phy? >>> If so, then you should model this driver as a single driver that >>> supports two PHYs similar to what Sylwester has done before? >> >> >> Best wishes, >> Kamil >> >>> Cheers >>> Kishon >>> >>>> >>>> Signed-off-by: Vivek Gautam <gautam.vivek@xxxxxxxxxxx> >>>> --- >>>> .../devicetree/bindings/phy/samsung-phy.txt | 20 + >>>> drivers/phy/Kconfig | 7 + >>>> drivers/phy/Makefile | 1 + >>>> drivers/phy/phy-exynos5-usb3.c | 562 >>> >>> ++++++++++++++++++++ >>>> >>>> 4 files changed, 590 insertions(+), 0 deletions(-) >>>> create mode 100644 drivers/phy/phy-exynos5-usb3.c >>>> >>>> diff --git a/Documentation/devicetree/bindings/phy/samsung-phy.txt >>>> b/Documentation/devicetree/bindings/phy/samsung-phy.txt >>>> index c0fccaa..9b5c111 100644 >>>> --- a/Documentation/devicetree/bindings/phy/samsung-phy.txt >>>> +++ b/Documentation/devicetree/bindings/phy/samsung-phy.txt >>>> @@ -20,3 +20,23 @@ Required properties: >>>> - compatible : should be "samsung,exynos5250-dp-video-phy"; >>>> - reg : offset and length of the Display Port PHY register set; >>>> - #phy-cells : from the generic PHY bindings, must be 0; >>>> + >>>> +Samsung Exynos5 SoC seiries USB 3.0 PHY controller >>>> +-------------------------------------------------- >>>> + >>>> +Required properties: >>>> +- compatible : >>>> + should be "samsung,exynos5250-usb3phy" for exynos5250 SoC >>>> + should be "samsung,exynos5420-usb3phy" for exynos5420 SoC >>>> +- reg : Register offset and length array >>>> + - first field corresponds to USB 3.0 PHY register set; >>>> + - second field corresponds to PHY power isolation register >>>> + present in PMU; >>>> +- clocks: Clock IDs array as required by the controller >>>> +- clock-names: names of clocks correseponding to IDs in the clock >>> >>> property; >>>> >>>> + Required clocks: >>>> + - first clock is main PHY clock (same as USB 3.0 controller IP >>> >>> clock) >>>> >>>> + - second clock is reference clock (usually crystal clock) >>>> + optional clock: >>>> + - third clock is special clock used by PHY for operation >>>> +- #phy-cells : from the generic PHY bindings, must be 0; >>>> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig index >>>> a344f3d..9a100c6 100644 >>>> --- a/drivers/phy/Kconfig >>>> +++ b/drivers/phy/Kconfig >>>> @@ -51,4 +51,11 @@ config PHY_EXYNOS_DP_VIDEO >>>> help >>>> Support for Display Port PHY found on Samsung EXYNOS SoCs. >>>> >>>> +config PHY_EXYNOS5_USB3 >>>> + tristate "Exynos5 SoC series USB 3.0 PHY driver" >>>> + depends on ARCH_EXYNOS5 >>>> + select GENERIC_PHY >>>> + help >>>> + Enable USB 3.0 PHY support for Exynos 5 SoC series >>>> + >>>> endmenu >>>> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile index >>>> d0caae9..9c06a61 100644 >>>> --- a/drivers/phy/Makefile >>>> +++ b/drivers/phy/Makefile >>>> @@ -7,3 +7,4 @@ obj-$(CONFIG_PHY_EXYNOS_DP_VIDEO) += >>>> phy-exynos-dp- >>> >>> video.o >>>> >>>> obj-$(CONFIG_PHY_EXYNOS_MIPI_VIDEO) += phy-exynos-mipi-video.o >>>> obj-$(CONFIG_OMAP_USB2) += phy-omap-usb2.o >>>> obj-$(CONFIG_TWL4030_USB) += phy-twl4030-usb.o >>>> +obj-$(CONFIG_PHY_EXYNOS5_USB3) += phy-exynos5-usb3.o >>>> diff --git a/drivers/phy/phy-exynos5-usb3.c >>>> b/drivers/phy/phy-exynos5-usb3.c new file mode 100644 index >>>> 0000000..b9a2674 >>>> --- /dev/null >>>> +++ b/drivers/phy/phy-exynos5-usb3.c >>>> @@ -0,0 +1,562 @@ >>>> +/* >>>> + * Samsung EXYNOS5 SoC series USB 3.0 PHY driver >>>> + * >>>> + * Copyright (C) 2013 Samsung Electronics Co., Ltd. >>>> + * Author: Vivek Gautam <gautam.vivek@xxxxxxxxxxx> >>>> + * >>>> + * This program is free software; you can redistribute it and/or >>>> +modify >>>> + * it under the terms of the GNU General Public License version 2 as >>>> + * published by the Free Software Foundation. >>>> + */ >>>> + >>>> +#include <linux/clk.h> >>>> +#include <linux/delay.h> >>>> +#include <linux/io.h> >>>> +#include <linux/kernel.h> >>>> +#include <linux/module.h> >>>> +#include <linux/of.h> >>>> +#include <linux/of_address.h> >>>> +#include <linux/phy/phy.h> >>>> +#include <linux/platform_device.h> >>>> +#include <linux/mutex.h> >>>> + >>>> +/* Exynos USB PHY registers */ >>>> +#define EXYNOS5_FSEL_9MHZ6 0x0 >>>> +#define EXYNOS5_FSEL_10MHZ 0x1 >>>> +#define EXYNOS5_FSEL_12MHZ 0x2 >>>> +#define EXYNOS5_FSEL_19MHZ2 0x3 >>>> +#define EXYNOS5_FSEL_20MHZ 0x4 >>>> +#define EXYNOS5_FSEL_24MHZ 0x5 >>>> +#define EXYNOS5_FSEL_50MHZ 0x7 >>>> + >>>> +/* EXYNOS5: USB 3.0 DRD PHY registers */ >>>> +#define EXYNOS5_DRD_LINKSYSTEM (0x04) >>>> + >>>> +#define LINKSYSTEM_FLADJ_MASK (0x3f << 1) >>>> +#define LINKSYSTEM_FLADJ(_x) ((_x) << 1) >>>> +#define LINKSYSTEM_XHCI_VERSION_CONTROL (0x1 << 27) >>>> + >>>> +#define EXYNOS5_DRD_PHYUTMI (0x08) >>>> + >>>> +#define PHYUTMI_OTGDISABLE (0x1 << 6) >>>> +#define PHYUTMI_FORCESUSPEND (0x1 << 1) >>>> +#define PHYUTMI_FORCESLEEP (0x1 << 0) >>>> + >>>> +#define EXYNOS5_DRD_PHYPIPE (0x0c) >>>> + >>>> +#define EXYNOS5_DRD_PHYCLKRST (0x10) >>>> + >>>> +#define PHYCLKRST_SSC_REFCLKSEL_MASK (0xff << 23) >>>> +#define PHYCLKRST_SSC_REFCLKSEL(_x) ((_x) << 23) >>>> + >>>> +#define PHYCLKRST_SSC_RANGE_MASK (0x03 << 21) >>>> +#define PHYCLKRST_SSC_RANGE(_x) ((_x) << 21) >>>> + >>>> +#define PHYCLKRST_SSC_EN (0x1 << 20) >>>> +#define PHYCLKRST_REF_SSP_EN (0x1 << 19) >>>> +#define PHYCLKRST_REF_CLKDIV2 (0x1 << 18) >>>> + >>>> +#define PHYCLKRST_MPLL_MULTIPLIER_MASK (0x7f << 11) >>>> +#define PHYCLKRST_MPLL_MULTIPLIER_100MHZ_REF (0x19 << 11) >>>> +#define PHYCLKRST_MPLL_MULTIPLIER_50M_REF (0x02 << 11) >>>> +#define PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF (0x68 << 11) >>>> +#define PHYCLKRST_MPLL_MULTIPLIER_20MHZ_REF (0x7d << 11) >>>> +#define PHYCLKRST_MPLL_MULTIPLIER_19200KHZ_REF (0x02 << 11) >>>> + >>>> +#define PHYCLKRST_FSEL_MASK (0x3f << 5) >>>> +#define PHYCLKRST_FSEL(_x) ((_x) << 5) >>>> +#define PHYCLKRST_FSEL_PAD_100MHZ (0x27 << 5) >>>> +#define PHYCLKRST_FSEL_PAD_24MHZ (0x2a << 5) >>>> +#define PHYCLKRST_FSEL_PAD_20MHZ (0x31 << 5) >>>> +#define PHYCLKRST_FSEL_PAD_19_2MHZ (0x38 << 5) >>>> + >>>> +#define PHYCLKRST_RETENABLEN (0x1 << 4) >>>> + >>>> +#define PHYCLKRST_REFCLKSEL_MASK (0x03 << 2) >>>> +#define PHYCLKRST_REFCLKSEL_PAD_REFCLK (0x2 << 2) >>>> +#define PHYCLKRST_REFCLKSEL_EXT_REFCLK (0x3 << 2) >>>> + >>>> +#define PHYCLKRST_PORTRESET (0x1 << 1) >>>> +#define PHYCLKRST_COMMONONN (0x1 << 0) >>>> + >>>> +#define EXYNOS5_DRD_PHYREG0 (0x14) >>>> +#define EXYNOS5_DRD_PHYREG1 (0x18) >>>> + >>>> +#define EXYNOS5_DRD_PHYPARAM0 (0x1c) >>>> + >>>> +#define PHYPARAM0_REF_USE_PAD (0x1 << 31) >>>> +#define PHYPARAM0_REF_LOSLEVEL_MASK (0x1f << 26) >>>> +#define PHYPARAM0_REF_LOSLEVEL (0x9 << 26) >>>> + >>>> +#define EXYNOS5_DRD_PHYPARAM1 (0x20) >>>> + >>>> +#define PHYPARAM1_PCS_TXDEEMPH_MASK (0x1f << 0) >>>> +#define PHYPARAM1_PCS_TXDEEMPH (0x1c) >>>> + >>>> +#define EXYNOS5_DRD_PHYTERM (0x24) >>>> + >>>> +#define EXYNOS5_DRD_PHYTEST (0x28) >>>> + >>>> +#define PHYTEST_POWERDOWN_SSP (0x1 << 3) >>>> +#define PHYTEST_POWERDOWN_HSP (0x1 << 2) >>>> + >>>> +#define EXYNOS5_DRD_PHYADP (0x2c) >>>> + >>>> +#define EXYNOS5_DRD_PHYBATCHG (0x30) >>>> + >>>> +#define PHYBATCHG_UTMI_CLKSEL (0x1 << 2) >>>> + >>>> +#define EXYNOS5_DRD_PHYRESUME (0x34) >>>> +#define EXYNOS5_DRD_LINKPORT (0x44) >>>> + >>>> + >>>> +/* Isolation, configured in the power management unit */ >>>> +#define EXYNOS5_USB_ISOL_DRD (1 << 0) >>>> + >>>> +#define CLKSEL_ERROR -1 >>>> + >>>> +#ifndef KHZ >>>> +#define KHZ 1000 >>>> +#endif >>>> + >>>> +#ifndef MHZ >>>> +#define MHZ (KHZ * KHZ) >>>> +#endif >>>> + >>>> +enum samsung_cpu_type { >>>> + TYPE_EXYNOS5250, >>>> + TYPE_EXYNOS5420, >>>> +}; >>>> + >>>> +enum usb3phy_state { >>>> + STATE_OFF, >>>> + STATE_ON, >>>> +}; >>>> + >>>> +struct usb3phy_config { >>>> + enum samsung_cpu_type cpu; >>>> + bool has_sclk_usbphy30; >>>> +}; >>>> + >>>> +struct usb3phy_instance { >>>> + char *label; >>>> + struct usb3phy_driver *drv; >>>> + struct phy *phy; >>>> + enum usb3phy_state state; >>>> + u32 clk; >>>> + unsigned long rate; >>>> +}; >>>> + >>>> +struct usb3phy_driver { >>>> + struct device *dev; >>>> + void __iomem *reg_phy; >>>> + void __iomem *reg_isol; >>>> + struct clk *clk; >>>> + struct clk *sclk_usbphy30; >>>> + struct usb3phy_instance instance; >>>> +}; >>>> + >>>> +/* >>>> + * exynos5_rate_to_clk() converts the supplied clock rate to the >>>> +value that >>>> + * can be written to the phy register. >>>> + */ >>>> +static u32 exynos5_rate_to_clk(unsigned long rate) { >>>> + unsigned int clksel; >>>> + >>>> + /* EXYNOS5_FSEL_MASK */ >>>> + >>>> + switch (rate) { >>>> + case 9600 * KHZ: >>>> + clksel = EXYNOS5_FSEL_9MHZ6; >>>> + break; >>>> + case 10 * MHZ: >>>> + clksel = EXYNOS5_FSEL_10MHZ; >>>> + break; >>>> + case 12 * MHZ: >>>> + clksel = EXYNOS5_FSEL_12MHZ; >>>> + break; >>>> + case 19200 * KHZ: >>>> + clksel = EXYNOS5_FSEL_19MHZ2; >>>> + break; >>>> + case 20 * MHZ: >>>> + clksel = EXYNOS5_FSEL_20MHZ; >>>> + break; >>>> + case 24 * MHZ: >>>> + clksel = EXYNOS5_FSEL_24MHZ; >>>> + break; >>>> + case 50 * MHZ: >>>> + clksel = EXYNOS5_FSEL_50MHZ; >>>> + break; >>>> + default: >>>> + clksel = CLKSEL_ERROR; >>>> + } >>>> + >>>> + return clksel; >>>> +} >>>> + >>>> +static void exynos5_usb3phy_isol(struct usb3phy_instance *inst, bool >>>> +on) { >>>> + struct usb3phy_driver *drv = inst->drv; >>>> + u32 tmp; >>>> + >>>> + if (!drv->reg_isol) >>>> + return; >>>> + >>>> + tmp = readl(drv->reg_isol); >>>> + if (on) >>>> + tmp &= ~EXYNOS5_USB_ISOL_DRD; >>>> + else >>>> + tmp |= EXYNOS5_USB_ISOL_DRD; >>>> + writel(tmp, drv->reg_isol); >>>> +} >>>> + >>>> +/* >>>> + * Sets the phy clk as EXTREFCLK (XXTI) which is internal clock from >>> >>> clock core. >>>> >>>> + */ >>>> +static u32 exynos5_usb3phy_set_refclk(struct usb3phy_instance *inst) >>>> +{ >>>> + u32 reg; >>>> + u32 refclk; >>>> + >>>> + refclk = inst->clk; >>>> + >>>> + reg = PHYCLKRST_REFCLKSEL_EXT_REFCLK | >>>> + PHYCLKRST_FSEL(refclk); >>>> + >>>> + switch (refclk) { >>>> + case EXYNOS5_FSEL_50MHZ: >>>> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_50M_REF | >>>> + PHYCLKRST_SSC_REFCLKSEL(0x00)); >>>> + break; >>>> + case EXYNOS5_FSEL_20MHZ: >>>> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_20MHZ_REF | >>>> + PHYCLKRST_SSC_REFCLKSEL(0x00)); >>>> + break; >>>> + case EXYNOS5_FSEL_19MHZ2: >>>> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_19200KHZ_REF | >>>> + PHYCLKRST_SSC_REFCLKSEL(0x88)); >>>> + break; >>>> + case EXYNOS5_FSEL_24MHZ: >>>> + default: >>>> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF | >>>> + PHYCLKRST_SSC_REFCLKSEL(0x88)); >>>> + break; >>>> + } >>>> + >>>> + return reg; >>>> +} >>>> + >>>> +static void exynos5_usb3phy_init(struct usb3phy_instance *inst) { >>>> + struct usb3phy_driver *drv = inst->drv; >>>> + u32 phyparam0; >>>> + u32 phyparam1; >>>> + u32 linksystem; >>>> + u32 phybatchg; >>>> + u32 phytest; >>>> + u32 phyclkrst; >>>> + >>>> + /* Reset USB 3.0 PHY */ >>>> + writel(0x0, drv->reg_phy + EXYNOS5_DRD_PHYREG0); >>>> + >>>> + phyparam0 = readl(drv->reg_phy + EXYNOS5_DRD_PHYPARAM0); >>>> + /* Select PHY CLK source */ >>>> + phyparam0 &= ~PHYPARAM0_REF_USE_PAD; >>>> + /* Set Loss-of-Signal Detector sensitivity */ >>>> + phyparam0 &= ~PHYPARAM0_REF_LOSLEVEL_MASK; >>>> + phyparam0 |= PHYPARAM0_REF_LOSLEVEL; >>>> + writel(phyparam0, drv->reg_phy + EXYNOS5_DRD_PHYPARAM0); >>>> + >>>> + writel(0x0, drv->reg_phy + EXYNOS5_DRD_PHYRESUME); >>>> + >>>> + /* >>>> + * Setting the Frame length Adj value[6:1] to default 0x20 >>>> + * See xHCI 1.0 spec, 5.2.4 >>>> + */ >>>> + linksystem = LINKSYSTEM_XHCI_VERSION_CONTROL | >>>> + LINKSYSTEM_FLADJ(0x20); >>>> + writel(linksystem, drv->reg_phy + EXYNOS5_DRD_LINKSYSTEM); >>>> + >>>> + phyparam1 = readl(drv->reg_phy + EXYNOS5_DRD_PHYPARAM1); >>>> + /* Set Tx De-Emphasis level */ >>>> + phyparam1 &= ~PHYPARAM1_PCS_TXDEEMPH_MASK; >>>> + phyparam1 |= PHYPARAM1_PCS_TXDEEMPH; >>>> + writel(phyparam1, drv->reg_phy + EXYNOS5_DRD_PHYPARAM1); >>>> + >>>> + phybatchg = readl(drv->reg_phy + EXYNOS5_DRD_PHYBATCHG); >>>> + phybatchg |= PHYBATCHG_UTMI_CLKSEL; >>>> + writel(phybatchg, drv->reg_phy + EXYNOS5_DRD_PHYBATCHG); >>>> + >>>> + /* PHYTEST POWERDOWN Control */ >>>> + phytest = readl(drv->reg_phy + EXYNOS5_DRD_PHYTEST); >>>> + phytest &= ~(PHYTEST_POWERDOWN_SSP | >>>> + PHYTEST_POWERDOWN_HSP); >>>> + writel(phytest, drv->reg_phy + EXYNOS5_DRD_PHYTEST); >>>> + >>>> + /* UTMI Power Control */ >>>> + writel(PHYUTMI_OTGDISABLE, drv->reg_phy + EXYNOS5_DRD_PHYUTMI); >>>> + >>>> + phyclkrst = exynos5_usb3phy_set_refclk(inst); >>>> + >>>> + phyclkrst |= PHYCLKRST_PORTRESET | >>>> + /* Digital power supply in normal operating mode */ >>>> + PHYCLKRST_RETENABLEN | >>>> + /* Enable ref clock for SS function */ >>>> + PHYCLKRST_REF_SSP_EN | >>>> + /* Enable spread spectrum */ >>>> + PHYCLKRST_SSC_EN | >>>> + /* Power down HS Bias and PLL blocks in suspend >>>> mode >>> >>> */ >>>> >>>> + PHYCLKRST_COMMONONN; >>>> + >>>> + writel(phyclkrst, drv->reg_phy + EXYNOS5_DRD_PHYCLKRST); >>>> + >>>> + udelay(10); >>>> + >>>> + phyclkrst &= ~PHYCLKRST_PORTRESET; >>>> + writel(phyclkrst, drv->reg_phy + EXYNOS5_DRD_PHYCLKRST); >>>> + >>>> +} >>>> + >>>> +static void exynos5_usb3phy_exit(struct usb3phy_instance *inst) { >>>> + struct usb3phy_driver *drv = inst->drv; >>>> + u32 phyutmi; >>>> + u32 phyclkrst; >>>> + u32 phytest; >>>> + >>>> + phyutmi = PHYUTMI_OTGDISABLE | >>>> + PHYUTMI_FORCESUSPEND | >>>> + PHYUTMI_FORCESLEEP; >>>> + writel(phyutmi, drv->reg_phy + EXYNOS5_DRD_PHYUTMI); >>>> + >>>> + /* Resetting the PHYCLKRST enable bits to reduce leakage current >>> >>> */ >>>> >>>> + phyclkrst = readl(drv->reg_phy + EXYNOS5_DRD_PHYCLKRST); >>>> + phyclkrst &= ~(PHYCLKRST_REF_SSP_EN | >>>> + PHYCLKRST_SSC_EN | >>>> + PHYCLKRST_COMMONONN); >>>> + writel(phyclkrst, drv->reg_phy + EXYNOS5_DRD_PHYCLKRST); >>>> + >>>> + /* Control PHYTEST to remove leakage current */ >>>> + phytest = readl(drv->reg_phy + EXYNOS5_DRD_PHYTEST); >>>> + phytest |= PHYTEST_POWERDOWN_SSP | >>>> + PHYTEST_POWERDOWN_HSP; >>>> + writel(phytest, drv->reg_phy + EXYNOS5_DRD_PHYTEST); } >>>> + >>>> +static int exynos5_usb3phy_power_on(struct phy *phy) { >>>> + struct usb3phy_instance *inst = phy_get_drvdata(phy); >>>> + struct usb3phy_driver *drv = inst->drv; >>>> + int ret; >>>> + >>>> + dev_info(drv->dev, "Request to power_on \"%s\" usb phy\n", >>>> + inst->label); >>>> + >>>> + if (drv->sclk_usbphy30) >>>> + clk_prepare_enable(drv->sclk_usbphy30); >>>> + >>>> + ret = clk_prepare_enable(drv->clk); >>>> + if (ret) >>>> + return ret; >>>> + >>>> + if (inst->state == STATE_ON) { >>>> + dev_err(drv->dev, "usb phy \"%s\" already on", >>>> + inst->label); >>>> + ret = -ENODEV; >>>> + goto err0; >>>> + } >>>> + >>>> + inst->state = STATE_ON; >>>> + >>>> + /* Initialize the PHY and power it ON */ >>>> + exynos5_usb3phy_init(inst); >>>> + exynos5_usb3phy_isol(inst, 0); >>>> + >>>> +err0: >>>> + clk_disable_unprepare(drv->clk); >>>> + >>>> + return ret; >>>> +} >>>> + >>>> +static int exynos5_usb3phy_power_off(struct phy *phy) { >>>> + struct usb3phy_instance *inst = phy_get_drvdata(phy); >>>> + struct usb3phy_driver *drv = inst->drv; >>>> + int ret; >>>> + >>>> + dev_info(drv->dev, "Request to power_off \"%s\" usb phy\n", >>>> + inst->label); >>>> + ret = clk_prepare_enable(drv->clk); >>>> + if (ret) >>>> + return ret; >>>> + >>>> + if (inst->state == STATE_OFF) { >>>> + dev_err(drv->dev, "usb phy \"%s\" already off", >>>> + inst->label); >>>> + ret = -ENODEV; >>>> + goto err0; >>>> + } >>>> + >>>> + inst->state = STATE_OFF; >>>> + >>>> + /* Power-off the PHY and de-initialize it */ >>>> + exynos5_usb3phy_isol(inst, 1); >>>> + exynos5_usb3phy_exit(inst); >>>> + >>>> +err0: >>>> + clk_disable_unprepare(drv->clk); >>>> + if (drv->sclk_usbphy30) >>>> + clk_disable_unprepare(drv->sclk_usbphy30); >>>> + >>>> + return ret; >>>> +} >>>> + >>>> +static struct phy_ops exynos5_usb3phy_ops = { >>>> + .power_on = exynos5_usb3phy_power_on, >>>> + .power_off = exynos5_usb3phy_power_off, >>>> + .owner = THIS_MODULE, >>>> +}; >>>> + >>>> +static const struct of_device_id exynos5_usb3phy_of_match[]; >>>> + >>>> +static int exynos5_usb3phy_probe(struct platform_device *pdev) { >>>> + struct device *dev = &pdev->dev; >>>> + struct usb3phy_driver *drv; >>>> + struct usb3phy_instance *inst; >>>> + struct phy_provider *phy_provider; >>>> + struct resource *res; >>>> + struct clk *clk; >>>> + const struct of_device_id *match; >>>> + const struct usb3phy_config *cfg; >>>> + >>>> + match = of_match_node(exynos5_usb3phy_of_match, pdev- >>>> dev.of_node); >>>> + if (!match) { >>>> + dev_err(dev, "of_match_node() failed\n"); >>>> + return -EINVAL; >>>> + } >>>> + cfg = match->data; >>>> + if (!cfg) { >>>> + dev_err(dev, "Failed to get configuration\n"); >>>> + return -EINVAL; >>>> + } >>>> + >>>> + drv = devm_kzalloc(dev, sizeof(struct usb3phy_driver), >>> >>> GFP_KERNEL); >>>> >>>> + if (!drv) { >>>> + dev_err(dev, "Failed to allocate memory\n"); >>>> + return -ENOMEM; >>>> + } >>>> + >>>> + dev_set_drvdata(dev, drv); >>>> + drv->dev = dev; >>>> + >>>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); >>>> + drv->reg_phy = devm_ioremap_resource(dev, res); >>>> + if (IS_ERR(drv->reg_phy)) { >>>> + dev_err(dev, "Failed to map register memory (phy)\n"); >>>> + return PTR_ERR(drv->reg_phy); >>>> + } >>>> + >>>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 1); >>>> + drv->reg_isol = devm_ioremap_resource(dev, res); >>>> + if (IS_ERR(drv->reg_isol)) { >>>> + dev_err(dev, "Failed to map register memory >>>> (isolation)\n"); >>>> + return PTR_ERR(drv->reg_isol); >>>> + } >>>> + >>>> + phy_provider = devm_of_phy_provider_register(dev, >>> >>> of_phy_simple_xlate); >>>> >>>> + if (IS_ERR(phy_provider)) { >>>> + dev_err(drv->dev, "Failed to register phy provider\n"); >>>> + return PTR_ERR(phy_provider); >>>> + } >>>> + >>>> + drv->clk = devm_clk_get(dev, "phy"); >>>> + if (IS_ERR(drv->clk)) { >>>> + dev_err(dev, "Failed to get clock of phy controller\n"); >>>> + return PTR_ERR(drv->clk); >>>> + } >>>> + >>>> + /* >>>> + * Exysno5420 SoC has an additional special clock, used for >>>> + * for USB 3.0 PHY operation, this clock goes to the PHY block >>>> + * as a reference clock to clock generation block of the >>> >>> controller. >>>> >>>> + */ >>>> + if (cfg->has_sclk_usbphy30) { >>>> + drv->sclk_usbphy30 = devm_clk_get(dev, "sclk_usbphy30"); >>>> + if (IS_ERR(drv->clk)) { >>>> + dev_err(dev, "Failed to get phy reference >>>> clock\n"); >>>> + return PTR_ERR(drv->clk); >>>> + } >>>> + } >>>> + >>>> + inst = &drv->instance; >>>> + inst->drv = drv; >>>> + inst->label = "usb3drd"; >>>> + >>>> + dev_info(dev, "Creating phy \"%s\"\n", inst->label); >>>> + inst->phy = devm_phy_create(dev, &exynos5_usb3phy_ops, NULL); >>>> + if (IS_ERR(inst->phy)) { >>>> + dev_err(drv->dev, "Failed to create usb3phy \"%s\"\n", >>>> + inst->label); >>>> + return PTR_ERR(inst->phy); >>>> + } >>>> + >>>> + phy_set_drvdata(inst->phy, inst); >>>> + >>>> + clk = clk_get(dev, inst->label); >>>> + if (IS_ERR(clk)) { >>>> + dev_err(dev, "Failed to get clock of \"%s\" phy\n", >>>> + inst->label); >>>> + return PTR_ERR(clk); >>>> + } >>>> + >>>> + inst->rate = clk_get_rate(clk); >>>> + >>>> + inst->clk = exynos5_rate_to_clk(inst->rate); >>>> + if (inst->clk == CLKSEL_ERROR) { >>>> + dev_err(dev, "Clock rate (%ld) not supported\n", >>>> + inst->rate); >>>> + clk_put(clk); >>>> + return -EINVAL; >>>> + } >>>> + clk_put(clk); >>>> + >>>> + return 0; >>>> +} >>>> + >>>> +const struct usb3phy_config exynos5420_usb3phy_cfg = { >>>> + .cpu = TYPE_EXYNOS5420, >>>> + .has_sclk_usbphy30 = true, >>>> +}; >>>> + >>>> +const struct usb3phy_config exynos5250_usb3phy_cfg = { >>>> + .cpu = TYPE_EXYNOS5250, >>>> + .has_sclk_usbphy30 = false, >>>> +}; >>>> + >>>> +static const struct of_device_id exynos5_usb3phy_of_match[] = { >>>> + { >>>> + .compatible = "samsung,exynos5250-usb3phy", >>>> + .data = &exynos5250_usb3phy_cfg >>>> + }, { >>>> + .compatible = "samsung,exynos5420-usb3phy", >>>> + .data = &exynos5420_usb3phy_cfg >>>> + }, >>>> + { }, >>>> +}; >>>> + >>>> +static struct platform_driver exynos5_usb3phy_driver = { >>>> + .probe = exynos5_usb3phy_probe, >>>> + .driver = { >>>> + .of_match_table = exynos5_usb3phy_of_match, >>>> + .name = "exynos5-usb3phy", >>>> + .owner = THIS_MODULE, >>>> + } >>>> +}; >>>> + >>>> +module_platform_driver(exynos5_usb3phy_driver); >>>> +MODULE_DESCRIPTION("Samsung EXYNOS5 series SoC USB 3.0 PHY driver"); >>>> +MODULE_AUTHOR("Vivek Gautam <gautam.vivek@xxxxxxxxxxx>"); >>>> +MODULE_LICENSE("GPL v2"); MODULE_ALIAS("platform:exynos5-usb3phy"); >>>> >> > > -- > To unsubscribe from this list: send the line "unsubscribe linux-usb" in > > the body of a message to majordomo@xxxxxxxxxxxxxxx > More majordomo info at http://vger.kernel.org/majordomo-info.html -- Best Regards Vivek Gautam Samsung R&D Institute, Bangalore India -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
