Chips prior to Tegra186 needed delay of 3 UART clock cycles to avoid
data loss. This issue is fixed in Tegra186 and a new flag is added to
check if FIFO mode is enabled. chip data updated to check if this flag
is available for a chip. Tegra186 has new compatible to enable this
flag.
Signed-off-by: Shardar Shariff Md <smohammed@xxxxxxxxxx>
Signed-off-by: Krishna Yarlagadda <kyarlagadda@xxxxxxxxxx>
---
drivers/tty/serial/serial-tegra.c | 52 ++++++++++++++++++++++++++++++++++-----
1 file changed, 46 insertions(+), 6 deletions(-)
diff --git a/drivers/tty/serial/serial-tegra.c b/drivers/tty/serial/serial-tegra.c
index c3f9913..69af621 100644
--- a/drivers/tty/serial/serial-tegra.c
+++ b/drivers/tty/serial/serial-tegra.c
@@ -72,6 +72,8 @@
#define TEGRA_TX_PIO 1
#define TEGRA_TX_DMA 2
+#define TEGRA_UART_FCR_IIR_FIFO_EN 0x40
+
/**
* tegra_uart_chip_data: SOC specific data.
*
@@ -84,6 +86,7 @@ struct tegra_uart_chip_data {
bool tx_fifo_full_status;
bool allow_txfifo_reset_fifo_mode;
bool support_clk_src_div;
+ bool fifo_mode_enable_status;
};
struct tegra_uart_port {
@@ -263,6 +266,21 @@ static void tegra_uart_wait_sym_time(struct tegra_uart_port *tup,
tup->current_baud));
}
+static int tegra_uart_wait_fifo_mode_enabled(struct tegra_uart_port *tup)
+{
+ unsigned long iir;
+ unsigned int tmout = 100;
+
+ do {
+ iir = tegra_uart_read(tup, UART_IIR);
+ if (iir & TEGRA_UART_FCR_IIR_FIFO_EN)
+ return 0;
+ udelay(1);
+ } while (--tmout);
+
+ return -ETIMEDOUT;
+}
+
static void tegra_uart_fifo_reset(struct tegra_uart_port *tup, u8 fcr_bits)
{
unsigned long fcr = tup->fcr_shadow;
@@ -282,6 +300,8 @@ static void tegra_uart_fifo_reset(struct tegra_uart_port *tup, u8 fcr_bits)
tegra_uart_write(tup, fcr, UART_FCR);
fcr |= UART_FCR_ENABLE_FIFO;
tegra_uart_write(tup, fcr, UART_FCR);
+ if (tup->cdata->fifo_mode_enable_status)
+ tegra_uart_wait_fifo_mode_enabled(tup);
}
/* Dummy read to ensure the write is posted */
@@ -917,12 +937,20 @@ static int tegra_uart_hw_init(struct tegra_uart_port *tup)
/* Dummy read to ensure the write is posted */
tegra_uart_read(tup, UART_SCR);
- /*
- * For all tegra devices (up to t210), there is a hardware issue that
- * requires software to wait for 3 UART clock periods after enabling
- * the TX fifo, otherwise data could be lost.
- */
- tegra_uart_wait_cycle_time(tup, 3);
+ if (tup->cdata->fifo_mode_enable_status) {
+ ret = tegra_uart_wait_fifo_mode_enabled(tup);
+ dev_err(tup->uport.dev, "FIFO mode not enabled\n");
+ if (ret < 0)
+ return ret;
+ } else {
+ /*
+ * For all tegra devices (up to t210), there is a hardware
+ * issue that requires software to wait for 3 UART clock
+ * periods after enabling the TX fifo, otherwise data could
+ * be lost.
+ */
+ tegra_uart_wait_cycle_time(tup, 3);
+ }
/*
* Initialize the UART with default configuration
@@ -1293,12 +1321,21 @@ static struct tegra_uart_chip_data tegra20_uart_chip_data = {
.tx_fifo_full_status = false,
.allow_txfifo_reset_fifo_mode = true,
.support_clk_src_div = false,
+ .fifo_mode_enable_status = false,
};
static struct tegra_uart_chip_data tegra30_uart_chip_data = {
.tx_fifo_full_status = true,
.allow_txfifo_reset_fifo_mode = false,
.support_clk_src_div = true,
+ .fifo_mode_enable_status = false,
+};
+
+static struct tegra_uart_chip_data tegra186_uart_chip_data = {
+ .tx_fifo_full_status = true,
+ .allow_txfifo_reset_fifo_mode = false,
+ .support_clk_src_div = true,
+ .fifo_mode_enable_status = true,
};
static const struct of_device_id tegra_uart_of_match[] = {
@@ -1309,6 +1346,9 @@ static const struct of_device_id tegra_uart_of_match[] = {
.compatible = "nvidia,tegra20-hsuart",
.data = &tegra20_uart_chip_data,
}, {
+ .compatible = "nvidia,tegra186-hsuart",
+ .data = &tegra186_uart_chip_data,
+ }, {
},
};
MODULE_DEVICE_TABLE(of, tegra_uart_of_match);
--
2.7.4
