On Tue, 6 May 2008, Andrew Vasquez wrote: > Date: Tue, 6 May 2008 06:51:18 -0700 > From: Andrew Vasquez <andrew.vasquez@xxxxxxxxxx> > To: Gerhard Mack <gmack@xxxxxxxxxxxxx> > Cc: linux-scsi@xxxxxxxxxxxxxxx, linux-kernel@xxxxxxxxxxxxxxx > Subject: Re: [2.6.25.1] qla2xxx can't see more than 4 drives > > On Sat, 03 May 2008, Gerhard Mack wrote: > > > I have an array witjh 6 drives in it and if use the card's utilities on > > boot it sees all of them but for some reason Linux only sees 4 drives. > > > > Am I running into a limit? I can see both drives if I remove other drives > > from the array. > > > > [0:0:0:0] disk MAXTOR ATLAS10K4_36SCA DFM0 /dev/sda > > [0:0:1:0] disk MAXTOR ATLAS10K4_36SCA DFM0 /dev/sdb > > [0:0:2:0] disk MAXTOR ATLAS10K4_36SCA DFM0 /dev/sdc > > [0:0:6:0] process PE/PV 1x3 SCSI BP 0.28 - > > fiber channel drives: > > [2:0:0:0] disk SEAGATE ST314680 CLAR146 7A0A /dev/sdd > > [2:0:1:0] disk SEAGATE ST314680 CLAR146 7A04 /dev/sde > > [2:0:2:0] disk SEAGATE ST314680 CLAR146 7A0A /dev/sdf > > [2:0:3:0] disk SEAGATE ST314680 CLAR146 7A04 /dev/sdg > > > > QLogic Fibre Channel HBA Driver > > qla2xxx 0000:02:0a.0: Found an ISP2312, irq 24, iobase 0xf88cc000 > > qla2xxx 0000:02:0a.0: Configuring PCI space... > > qla2xxx 0000:02:0a.0: Configure NVRAM parameters... > > qla2xxx 0000:02:0a.0: Verifying loaded RISC code... > > qla2xxx 0000:02:0a.0: Allocated (412 KB) for firmware dump... > > scsi3 : qla2xxx > > qla2xxx 0000:02:0a.0: LIP reset occured (f8f7). > > qla2xxx 0000:02:0a.0: LIP occured (f8f7). > > qla2xxx 0000:02:0a.0: LOOP UP detected (1 Gbps). > > Could you load the driver with the ql2xextended_error_logging module > parameter set to 1 and send the resultant driver logs? Also, it would > could you also send the output of the following after the driver is > loaded: > > $ cat /sys/class/fc_host/host<host_no> > $ cat /sys/class/scsi_host/host<host_no>/* > $ cat /sys/class/fc_remote_ports/* > > where host_no corresponds to the SCSI host-number assigned to the HBA. > Of course.. QLogic Fibre Channel HBA Driver qla2xxx 0000:02:0a.0: Found an ISP2312, irq 24, iobase 0xf88cc000 qla2xxx 0000:02:0a.0: Configuring PCI space... qla2xxx 0000:02:0a.0: Configure NVRAM parameters... qla2xxx 0000:02:0a.0: Verifying loaded RISC code... scsi(4): **** Load RISC code **** scsi(4): Verifying Checksum of loaded RISC code. scsi(4): Checksum OK, start firmware. qla2xxx 0000:02:0a.0: Allocated (412 KB) for firmware dump... scsi(4): Issue init firmware. DEBUG: detect hba 4 at address = f5da2278 scsi4 : qla2xxx scsi(4): Asynchronous LIP RESET (f8f7). qla2xxx 0000:02:0a.0: LIP reset occured (f8f7). scsi(4): LIP occured (f8f7). qla2xxx 0000:02:0a.0: LIP occured (f8f7). scsi(4): Asynchronous LOOP UP (1 Gbps). qla2xxx 0000:02:0a.0: LOOP UP detected (1 Gbps). scsi(4): Asynchronous PORT UPDATE. scsi(4): Port database changed ffff 0006 0000. scsi(4): qla2x00_reset_marker() scsi(4): qla2x00_loop_resync() scsi(4): F/W Ready - OK scsi(4): fw_state=3 curr time=1371fd39. scsi(4): Configure loop -- dpc flags =0x40800e0 qla2x00_mailbox_command(4): **** FAILED. mbx0=4006, mbx1=7e, mbx2=0, cmd=6a **** qla2x00_get_port_name(4): failed=102. scsi(4): MBC_GET_PORT_NAME Failed, No FL Port scsi(4): LOOP READY scsi(4): qla2x00_loop_resync - end qla2xxx 0000:02:0a.0: scsi(4:0:0:0): Queue depth adjusted-up to 4. scsi 4:0:0:0: Direct-Access SEAGATE ST314680 CLAR146 7A0A PQ: 0 ANSI: 3 sd 4:0:0:0: [sdd] 286749476 512-byte hardware sectors (146816 MB) sd 4:0:0:0: [sdd] Write Protect is off sd 4:0:0:0: [sdd] Mode Sense: a7 00 10 08 sd 4:0:0:0: [sdd] Write cache: enabled, read cache: enabled, supports DPO and FUA sd 4:0:0:0: [sdd] 286749476 512-byte hardware sectors (146816 MB) sd 4:0:0:0: [sdd] Write Protect is off sd 4:0:0:0: [sdd] Mode Sense: a7 00 10 08 sd 4:0:0:0: [sdd] Write cache: enabled, read cache: enabled, supports DPO and FUA sdd:<6>qla2xxx 0000:02:0a.0: QLogic Fibre Channel HBA Driver: 8.02.00-k9-debug QLogic QLA2340 - 133MHz PCI-X to 2Gb FC, Single Channel ISP2312: PCI (66 MHz) @ 0000:02:0a.0 hdma-, host#=4, fw=3.03.20 IPX unknown partition table sd 4:0:0:0: [sdd] Attached SCSI disk sd 4:0:0:0: Attached scsi generic sg4 type 0 sd 4:0:0:0: Embedded Enclosure Device sd 4:0:0:0: Failed to get diagnostic page 0x6000000 sd 4:0:0:0: Failed to bind enclosure -19 qla2xxx 0000:02:0a.0: scsi(4:0:1:0): Queue depth adjusted-up to 4. scsi 4:0:1:0: Direct-Access SEAGATE ST314680 CLAR146 7A04 PQ: 0 ANSI: 3 sd 4:0:1:0: [sde] 286749476 512-byte hardware sectors (146816 MB) sd 4:0:1:0: [sde] Write Protect is off sd 4:0:1:0: [sde] Mode Sense: a7 00 10 08 sd 4:0:1:0: [sde] Write cache: disabled, read cache: enabled, supports DPO and FUA sd 4:0:1:0: [sde] 286749476 512-byte hardware sectors (146816 MB) sd 4:0:1:0: [sde] Write Protect is off sd 4:0:1:0: [sde] Mode Sense: a7 00 10 08 sd 4:0:1:0: [sde] Write cache: disabled, read cache: enabled, supports DPO and FUA sde: unknown partition table sd 4:0:1:0: [sde] Attached SCSI disk sd 4:0:1:0: Attached scsi generic sg5 type 0 sd 4:0:1:0: Embedded Enclosure Device sd 4:0:1:0: Failed to get diagnostic page 0x6000000 sd 4:0:1:0: Failed to bind enclosure -19 qla2xxx 0000:02:0a.0: scsi(4:0:2:0): Queue depth adjusted-up to 4. scsi 4:0:2:0: Direct-Access SEAGATE ST314680 CLAR146 7A0A PQ: 0 ANSI: 3 sd 4:0:2:0: [sdf] 286749476 512-byte hardware sectors (146816 MB) sd 4:0:2:0: [sdf] Write Protect is off sd 4:0:2:0: [sdf] Mode Sense: a7 00 10 08 sd 4:0:2:0: [sdf] Write cache: disabled, read cache: enabled, supports DPO and FUA sd 4:0:2:0: [sdf] 286749476 512-byte hardware sectors (146816 MB) sd 4:0:2:0: [sdf] Write Protect is off sd 4:0:2:0: [sdf] Mode Sense: a7 00 10 08 sd 4:0:2:0: [sdf] Write cache: disabled, read cache: enabled, supports DPO and FUA sdf: unknown partition table sd 4:0:2:0: [sdf] Attached SCSI disk sd 4:0:2:0: Attached scsi generic sg6 type 0 sd 4:0:2:0: Embedded Enclosure Device qla2xxx_eh_abort(4): aborting sp f7fce920 from RISC. pid=95. scsi(4): ABORT status detected 0x5-0x0. qla2xxx 0000:02:0a.0: scsi(4:2:0): Abort command issued -- 1 5f 2002. qla2xxx_eh_abort(4): aborting sp f7fce920 from RISC. pid=110. scsi(4): ABORT status detected 0x5-0x0. qla2xxx 0000:02:0a.0: scsi(4:2:0): Abort command issued -- 1 6e 2002. qla2xxx_eh_abort(4): aborting sp f7fce920 from RISC. pid=112. scsi(4): ABORT status detected 0x5-0x0. qla2xxx 0000:02:0a.0: scsi(4:2:0): Abort command issued -- 1 70 2002. qla2xxx_eh_abort(4): aborting sp f7fce920 from RISC. pid=115. scsi(4): ABORT status detected 0x5-0x0. qla2xxx 0000:02:0a.0: scsi(4:2:0): Abort command issued -- 1 73 2002. sd 4:0:2:0: Failed to get diagnostic page 0x80000 sd 4:0:2:0: Failed to bind enclosure -19 qla2xxx 0000:02:0a.0: scsi(4:0:3:0): Queue depth adjusted-up to 4. scsi 4:0:3:0: Direct-Access SEAGATE ST314680 CLAR146 7A04 PQ: 0 ANSI: 3 sd 4:0:3:0: [sdg] 286749476 512-byte hardware sectors (146816 MB) sd 4:0:3:0: [sdg] Write Protect is off sd 4:0:3:0: [sdg] Mode Sense: a7 00 10 08 sd 4:0:3:0: [sdg] Write cache: disabled, read cache: enabled, supports DPO and FUA sd 4:0:3:0: [sdg] 286749476 512-byte hardware sectors (146816 MB) sd 4:0:3:0: [sdg] Write Protect is off sd 4:0:3:0: [sdg] Mode Sense: a7 00 10 08 sd 4:0:3:0: [sdg] Write cache: disabled, read cache: enabled, supports DPO and FUA sdg: unknown partition table sd 4:0:3:0: [sdg] Attached SCSI disk sd 4:0:3:0: Attached scsi generic sg7 type 0 sd 4:0:3:0: Embedded Enclosure Device qla2xxx_eh_abort(4): aborting sp f6ddb160 from RISC. pid=137. scsi(4): ABORT status detected 0x5-0x0. qla2xxx 0000:02:0a.0: scsi(4:3:0): Abort command issued -- 1 89 2002. qla2xxx_eh_abort(4): aborting sp f73c4a80 from RISC. pid=149. scsi(4): ABORT status detected 0x5-0x0. qla2xxx 0000:02:0a.0: scsi(4:3:0): Abort command issued -- 1 95 2002. qla2xxx_eh_abort(4): aborting sp f6ddb080 from RISC. pid=158. scsi(4): ABORT status detected 0x5-0x0. qla2xxx 0000:02:0a.0: scsi(4:3:0): Abort command issued -- 1 9e 2002. qla2xxx_eh_abort(4): aborting sp f6ddb080 from RISC. pid=161. scsi(4): ABORT status detected 0x5-0x0. qla2xxx 0000:02:0a.0: scsi(4:3:0): Abort command issued -- 1 a1 2002. sd 4:0:3:0: Failed to get diagnostic page 0x80000 sd 4:0:3:0: Failed to bind enclosure -19 cat /sys/class/fc_host/host4/* : 0x200000e08b127d20 0 0x200000e08b127d20 0 0x000001 0x210000e08b127d20 Online LPort (private loop) 1 Gbit Class 3 QLA2340 FW:v3.03.20 DVR:v8.02.00-k9-debug wwpn (World Wide Port Name) cat /sys/class/scsi_host/host4/* : Initiator Disabled 2176 3 8.02.00-k9-debug 3.03.20 IPX 0 4953 5020 2020 0002 ISP2312 133MHz PCI-X to 2Gb FC, Single Channel QLA2340 1.54 0.00 0.00 0.00.00 0 PCI (66 MHz) <NULL> L87965 128 Link Up - Loop Initiator 0 0 Disabled 200 us cat /sys/class/fc_remote_ports/rport-4\:0-0/* : 35 0x2000000c507ce546 0x0000e2 0x2200000c507ce546 Online FCP Target 0 Class 3 cat /sys/class/fc_remote_ports/rport-4\:0-1/* 35 0x20000004cf69c688 0x0000e1 0x22000004cf69c688 Online FCP Target 1 Class 3 cat /sys/class/fc_remote_ports/rport-4\:0-2/* | log 35 0x2000000c507ce809 0x00000f 0x2200000c507ce809 Online FCP Target 2 Class 3 cat /sys/class/fc_remote_ports/rport-4\:0-3/* : 35 0x20000004cf69b98f 0x000008 0x22000004cf69b98f Online FCP Target 3 Class 3 -- Gerhard Mack gmack@xxxxxxxxxxxxx <>< As a computer I find your faith in technology amusing. -- To unsubscribe from this list: send the line "unsubscribe linux-scsi" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
