I have an array witjh 6 drives in it and if use the card's utilities on boot it sees all of them but for some reason Linux only sees 4 drives. Am I running into a limit? I can see both drives if I remove other drives from the array. [0:0:0:0] disk MAXTOR ATLAS10K4_36SCA DFM0 /dev/sda [0:0:1:0] disk MAXTOR ATLAS10K4_36SCA DFM0 /dev/sdb [0:0:2:0] disk MAXTOR ATLAS10K4_36SCA DFM0 /dev/sdc [0:0:6:0] process PE/PV 1x3 SCSI BP 0.28 - fiber channel drives: [2:0:0:0] disk SEAGATE ST314680 CLAR146 7A0A /dev/sdd [2:0:1:0] disk SEAGATE ST314680 CLAR146 7A04 /dev/sde [2:0:2:0] disk SEAGATE ST314680 CLAR146 7A0A /dev/sdf [2:0:3:0] disk SEAGATE ST314680 CLAR146 7A04 /dev/sdg QLogic Fibre Channel HBA Driver qla2xxx 0000:02:0a.0: Found an ISP2312, irq 24, iobase 0xf88cc000 qla2xxx 0000:02:0a.0: Configuring PCI space... qla2xxx 0000:02:0a.0: Configure NVRAM parameters... qla2xxx 0000:02:0a.0: Verifying loaded RISC code... qla2xxx 0000:02:0a.0: Allocated (412 KB) for firmware dump... scsi3 : qla2xxx qla2xxx 0000:02:0a.0: LIP reset occured (f8f7). qla2xxx 0000:02:0a.0: LIP occured (f8f7). qla2xxx 0000:02:0a.0: LOOP UP detected (1 Gbps). scsi 3:0:0:0: Direct-Access SEAGATE ST314680 CLAR146 7A0A PQ: 0 ANSI: 3 sd 3:0:0:0: [sdd] 286749476 512-byte hardware sectors (146816 MB) sd 3:0:0:0: [sdd] Write Protect is off sd 3:0:0:0: [sdd] Mode Sense: a7 00 10 08 sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, supports DPO and FUA sd 3:0:0:0: [sdd] 286749476 512-byte hardware sectors (146816 MB) sd 3:0:0:0: [sdd] Write Protect is off sd 3:0:0:0: [sdd] Mode Sense: a7 00 10 08 sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, supports DPO and FUA sdd:<6>qla2xxx 0000:02:0a.0: QLogic Fibre Channel HBA Driver: 8.02.00-k9 QLogic QLA2340 - 133MHz PCI-X to 2Gb FC, Single Channel ISP2312: PCI (66 MHz) @ 0000:02:0a.0 hdma-, host#=3, fw=3.03.20 IPX unknown partition table sd 3:0:0:0: [sdd] Attached SCSI disk sd 3:0:0:0: Attached scsi generic sg4 type 0 sd 3:0:0:0: Embedded Enclosure Device sd 3:0:0:0: Failed to get diagnostic page 0x6000000 sd 3:0:0:0: Failed to bind enclosure -19 scsi 3:0:1:0: Direct-Access SEAGATE ST314680 CLAR146 7A04 PQ: 0 ANSI: 3 sd 3:0:1:0: [sde] 286749476 512-byte hardware sectors (146816 MB) sd 3:0:1:0: [sde] Write Protect is off sd 3:0:1:0: [sde] Mode Sense: a7 00 10 08 sd 3:0:1:0: [sde] Write cache: disabled, read cache: enabled, supports DPO and FUA sd 3:0:1:0: [sde] 286749476 512-byte hardware sectors (146816 MB) sd 3:0:1:0: [sde] Write Protect is off sd 3:0:1:0: [sde] Mode Sense: a7 00 10 08 sd 3:0:1:0: [sde] Write cache: disabled, read cache: enabled, supports DPO and FUA sde: unknown partition table sd 3:0:1:0: [sde] Attached SCSI disk sd 3:0:1:0: Attached scsi generic sg5 type 0 sd 3:0:1:0: Embedded Enclosure Device sd 3:0:1:0: Failed to get diagnostic page 0x6000000 sd 3:0:1:0: Failed to bind enclosure -19 scsi 3:0:2:0: Direct-Access SEAGATE ST314680 CLAR146 7A0A PQ: 0 ANSI: 3 sd 3:0:2:0: [sdf] 286749476 512-byte hardware sectors (146816 MB) sd 3:0:2:0: [sdf] Write Protect is off sd 3:0:2:0: [sdf] Mode Sense: a7 00 10 08 sd 3:0:2:0: [sdf] Write cache: disabled, read cache: enabled, supports DPO and FUA sd 3:0:2:0: [sdf] 286749476 512-byte hardware sectors (146816 MB) sd 3:0:2:0: [sdf] Write Protect is off sd 3:0:2:0: [sdf] Mode Sense: a7 00 10 08 sd 3:0:2:0: [sdf] Write cache: disabled, read cache: enabled, supports DPO and FUA sdf: unknown partition table sd 3:0:2:0: [sdf] Attached SCSI disk sd 3:0:2:0: Attached scsi generic sg6 type 0 sd 3:0:2:0: Embedded Enclosure Device qla2xxx 0000:02:0a.0: scsi(3:2:0): Abort command issued -- 1 62 2002. qla2xxx 0000:02:0a.0: scsi(3:2:0): Abort command issued -- 1 6d 2002. -- Gerhard Mack gmack@xxxxxxxxxxxxx <>< As a computer I find your faith in technology amusing. -- To unsubscribe from this list: send the line "unsubscribe linux-scsi" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
